LAVAMAT BELLA 3850 Lave-linge Mode d'emploi
Chère cliente, cher client Veuillez lire attentivement la notice d’utilisation dans son intégralité et la conserver pour pouvoir la consulter ultérieurement. Veuillez la transmettre à l’éventuel futur propriétaire de l’appareil. 1 3 2 2 Les symboles suivants sont utilisés dans ce document : Consignes de sécurité Avertissement ! Conseils pour votre sécurité personnelle. Avertissement ! Consignes permettant d’éviter d’endommager l’appareil.
Sommaire Mode d'emploi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description de l’appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Panneau de commande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Synoptique des programmes . . . . . . . . . . . . . . .
Instructions de montage et de raccordement . . . . . . . . . . . 27 Consignes de sécurité pour l’installateur . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Mise en place du lave-linge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transport du lave-linge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enlevez les protections de transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lieu d’installation. . . . . .
Mode d'emploi 1 Sécurité Avant la première mise en service • Respecter les “Consignes d’installation et de raccordement”. • Si l’appareil est livré en hiver à une température au-dessous de 0°C : Entreposer le lave-linge pendant 24 heures à température ambiante avant sa mise en service. Utilisation conforme à l’usage prévu • Le lave-linge est uniquement destiné au lavage de linge de maison. • Il est interdit de transformer ou d’apporter des modifications au lavelinge.
Sécurité générale • Toute réparation du lave-linge automatique doit être uniquement effectuée par du personnel spécialisé. • Ne jamais mettre en marche le lave-linge si le câble électrique est détérioré ou bien si le bandeau de commande, le plan de travail ou la plinthe sont endommagés et permettent donc d’accéder à l’intérieur de l’appareil. • Eteindre le lave-linge avant le nettoyage, l’entretien et les opérations de maintenance.
Description de l’appareil Bac-tiroir pour produits lessiviels Bandeau de commande Plaque signalétique (derrière le hublot) Pieds vissables (ajustables en hauteur) Trappe du socle/ Pompe de vidange Panneau de commande Touche vitesse d’essorage/ ARRET CUVE PLEINE Multiafficheur Touche DEPART DIFFERE Touches additionnelles Touche MARCHE/PAUSE Affichage du déroulement du programme Voyant PORTE Programmateur Voyant SURDOSAGE 7
Synoptique des programmes • 40-60 MIX 5kg • 2,5kg • 1kg 2,5kg SYNTHETIQUES 60, 50, 40, 30 FACILE A REPASSER 40 LINGE DELICAT 40, 30 LAINE/SOIE H (lavage à la main) 40, 30, FROID RINCAGE DELICAT • • • • • • • •4) • • • • • • • • • • • • •4) • • • • • • • • • • • • •4) • • 2kg • • 2,5kg • • COURT ARRET CUVE PLEINE 5kg 1000/600 BLANC/COULEURS 95, 60, 40, 30 1800/1400 • SENSIBLE 5kg TACHES RINCAGE + ECONOMIQUE 2) Programme Vitesse d’essorage PRE
Utilisation/Caractéristiques Programme en mode économie d’énergie à 60 °C pour blanc/couleurs en coton/lin peu à normalement sale. Programme pour linge blanc/couleurs en coton/lin normalement sale à très sale. Programme pour blanc/couleurs dont les étiquettes indiquent différentes températures. Ce programme permet de laver en même temps des pièces normalement lavées séparément à 40 °C ou à 60 °C. L’optimisation de la capacité du tambour permet d’économiser de l’énergie.
Avant le premier lavage Pour retirer d’éventuels objets utilisés pour la fabrication du tambour et le compartiment à lessive, procéder à une premier lavage sans linge. Programme : BLANC/COULEURS 95, appuyer sur le bouton COURT et ajouter environ 1/4 de doseur de poudre de lessive. Préparation et tri du linge Préparation du linge • Vider les poches. Eliminer les corps étrangers (par exemple, pièces de monnaie, trombones, aiguilles, etc.).
Effectuer un programme de lavage Ouvrir la porte/Charger le tambour 1. Ouvrir la porte : tirer sur la poignée de la porte.
liser que la moitié du dosage recommandé pour les lavages à pleine charge. • A partir d’une dureté de l’eau de 2 (= moyenne), il est indispensable d’utiliser un anti-calcaire. La lessive peut alors être dosée pour une dureté de l’eau de 1 (=peu dure). Vous pouvez obtenir des informations sur la dureté de l’eau de votre ville auprès de l’usine des eaux compétente. 1. Ouvrir le compartiment à lessive jusqu’à la butée. 2. Verser la lessive/ ou le produit d’entretien. 3.
Mettre en marche la machine/Sélectionner le programme 3 Régler le programme et la température à l’aide du sélecteur de programme. Dès que vous avez sélectionné un programme, mettez immédiatement la machine en marche. – Le voyant de déroulement du programme indique les étapes du programme qui seront exécutées par ce dernier. – La durée prévue du programme est indiquée sur l’afficheur multiple (en minutes).
Sélectionner les compléments de programme 3 Si vous le souhaitez, vous pouvez appuyer sur le(s) bouton(s) des compléments de programme. Le voyant correspondant s’allume. L’apparition du message « Err » sur le multiafficheur signifie que le complément de programme sélectionné n’est pas compatible avec le programme de lavage choisi. RINCAGE + Les programmes ECONOMIQUE, BLANC/COULEURS, LINGE DELICAT, SYNTHETIQUES et FACILE A REPASSER comportent deux cycles de rinçage supplémentaires (par ex.
Régler le départ différé 3 3 La touche DEPART DIFFERE vous permet de décaler le démarrage d'un programme de 30 minutes (30') à 23 heures max. (23h). 1. Sélectionner un programme. 2. Appuyer plusieurs fois sur la touche DEPART DIFFERE jusqu'à ce que le décalage souhaité pour le démarrage du programme soit indiqué sur l'afficheur mutiple, par ex. 12h, si vous souhaitez que le programme démarre dans 12 heures. Le voyant DEPART DIFFERE s’allume.
Interrompre le programme/ Introduire du linge supplémentaire Interrompre le programme • En appuyant sur le bouton MARCHE/PAUSE, vous pouvez interrompre un programme à tout moment et le poursuivre en appuyant à nouveau sur le bouton MARCHE/PAUSE. • En cas d’interruption anticipée d’un programme, placez le sélecteur de programme sur ARRÊT.
Surdosage 3 Lorsque le voyant SURDOSAGE s’allume, cela signifie que vous avez surdosé le produit de lavage pour le programme en cours. Lors de votre prochaine lessive, respectez les instructions de dosage du fabricant du produit de lavage ainsi que le chargement! Sécurité enfants Lorsque la sécurité enfants est activée, le hublot ne peut plus être fermé.
Nettoyage Si vous lavez la plupart du temps à basse température, veuillez effectuer de temps en temps un programme á haute température (60 ou 90°). Ceci évite d’éventuels dépôts et l’appareil sera nettoyé de l’intérieur. Boîte à produits lessiviels Il est recommandé de nettoyer régulièrement la boîte à produits. 1. Tirez d’un coup sec sur la boîte à produits. 2. Enlevez l’élément supérieur du compartiment pour asssouplissant. 3. Nettoyez tous les éléments avec de l’eau. 4.
Hublot et joints en caoutchouc Verifiez régulièrement qu’il n’y a pas de dépôts ou de corps étrangers dans les fentes des joints en caoutchouc ou sur la face intérieure de la vitre du hublot. Nettoyez régulièrement la vitre du hublot et les joints en caoutchouc. Que faire quand...
Problème Cause possible E40 s’affiche. Le voyant FIN cliLe hublot n’est pas correctegnote 4 fois et un siment fermé. gnal sonore retentit simultanément. E10 s’affiche. Le voyant FIN clignote 1 fois et un signal sonore retentit 1 fois. (problèmes d’alimentation en eau) Solution Fermez correctement le hublot. Lancez de nouveau le programme. Le robinet d’arrivée d’eau est fermé. Ouvrez le robinet d’arrivée d’eau. Le filtre du raccord du flexible d’arrivée d’eau est bouché.
Problème EF0 s’affiche. Le voyant FIN clignote 15 fois et, simultanément, un signal sonore retentit 15 fois. La pompe de vidange ne s’arrête pas, même lorsque l’appareil est désactivé. Cause possible Le dispositif Aqua Control de protection contre les inondations s’est enclenché. Solution Fermez le robinet d’eau, débranchez l’appareil et contactez le service après-vente. La lessive produit beaucoup de mousDosez le produit de lavage en se.
Problème Cause possible Le hublot est verrouillé. Le hublot ne s’ouvre pas lorsque l’appareil Panne de courant ! (tous les voyants sont éteints) est sous tension. Le hublot reste verrouillé pendant 4 à 10 minutes. Le linge est très froissé. Solution Attendez jusqu’à ce que le voyant PORTE soit vert. Le programme se poursuit après rétablissement du courant.
Effectuer une vidange de secours 1 Avertissement ! Avant de commencer une vidange de secours, mettre le lave-linge hors tension et le débrancher ! Avertissement ! L’eau de lavage qui s’écoule du flexible de vidange de secours peut être brûlante. Danger de brûlure par aspersion ! Laisser refroidir l’eau de lavage avant de procéder à une vidange de secours ! 1. Soulever le clapet du socle et le retirer. 2. Sortir le flexible de vidange de secours. 3. Placer une coupelle sur le sol.
Pompe de vidange 1 La pompe de vidange ne nécessite aucun entretien. Il n’est pas nécessaire d’ouvrir le couvercle de la pompe, excepté en cas de dysfonctionnement ou que la vidange s’interrompt comme par ex. lorsque la roue de la pompe est bloquée. Avant d’introduire le linge, veuillez toujours vérifier qu’il ne reste aucun élément étranger dans les poches ou entre les vêtements. Les trombones, épingles, etc.
Protection de l’environnement 2 2 Elimination du matériel d’emballage Les matériaux d’emballage sont écologiques et recyclables. Les matières plastiques portent un signe distinctif, par ex. >PE<, >PS<, etc. Eliminez les matériaux d’emballage en fonction de leur signe distinctif dans les containeurs prévus à cet effet sur le site de collecte de votre commune. Appareils usagés W Le symbole sur le produit ou son emballage indique que ce produit ne peut être traité comme déchet ménager.
Caractéristiques techniques 5 Cet appareil est conforme aux directives UE suivantes : – directive 73/23/CEE du 19.02.1973 relative à la basse tension – directive 89/336/CEE du 03.05.1989 relative à la compatibilité électromagnétique (CEM) ainsi qu’à la directive de révision 92/31/CEE – directive 93/68/CEE du 22.07.1993 relative à la certification CE Hauteur x largeur x profondeur 850 x 598 x 603mm Profondeur, hublot ouvert 980 mm Réglage de la hauteur env.
Instructions de montage et de raccordement 1 Consignes de sécurité pour l’installateur • Ce lave-linge n’est pas encastrable. • Avant de le mettre en service, vérifier qu’il n’ait pas subi de dommages pendant le transport. Ne brancher en aucun cas un appareil endommagé. En cas de dommages, veuillez contacter votre concessionnaire. • Avant la mise en service, retirer tous les éléments du dispositif de sécurité.
Mise en place du lave-linge Transport du lave-linge 1 Avertissement ! Le lave-linge pèse lourd. Danger de blessures ! Faire attention lors du soulèvement. • Ne pas poser le lave-linge sur la façade ni sur le flanc droit (vu de devant). Les composants électriques peuvent se mouiller. • Ne jamais transporter le lave-linge sans les fixations de transport.
2. Redressez l'appareil et retirez la fixation du câble d’alimentation électrique et du tuyau de vidange des leur support placé à l’arrière de l’appareil. 3. Avec une clé dévissez et ôtez la vis centrale arrière A, en haut. Enlevez avec soin le goujon en plastique correspondant. 4. Dévissez et ôtez les deux grandes vis arrière B et les six petites vis C, en bas.
5. Sortez le rail de transport D. 6. Revissez les six petites vis C à leur place (voir figure ci-desssous). 7. Ouvrez le hublot et enlevez le bloc en polystyrène accroché avec du ruban adhésif au joint du hublot. 8. Bouchez l’ ouverture centrale et les deux ouvertures (en bas) à l’aide des caches plastique se trouvant dans l’enveloppe contenant la notice d’utilisation.
portez jamais l’appareil sans les protections de transport. Branchez le tuyau d’alimentation de la façon décrite au paragraphe “Raccordement d’eau”. Lieu d’installation Attention ! Le lave-linge ne doit pas être utilisé dans un local exposé au gel. Dommages dus au gel ou possibles dysfonctionnements ! Les dommages dus au gel ne sont pas couverts par la garantie ! • La surface d’appui doit être solide et plane.
Raccordement de l’eau Pression d’eau admise La pression de l’eau doit être comprise entre 1bar minimum (=10N/ cm2 =0,1MPa) et 10 bars maximum (=100N/cm2 =1MPa). – Si elle est supérieure à 10 bars : Relier la vanne de réduction de pression. – Si elle est inférieure à 1 bar : Visser le tuyau d’arrivée de l’eau à la soupape d’admission magnétique et sortir le régulateur de débit (pour ce faire, enlever le filtre avec la tige pointue et enlever la rondelle en caoutchouc se trouvant derrière).
4. Vissez le raccord du tuyau d’alimentation sur le nez fileté du robinet d’arrivée d’eau (20x27). Utilisez toujours le tuyau d’alimentation livré avec l’appareil. Vissez correctement pour éviter toute fuite. Si le branchement se fait sur des tuyauteries neuves ou qui n’ont pas servi depuis longtemps, il est préférable de faire couler une certaine quantité d’eau avant de mettre en place le tuyau de remplissage.
Evacuation de l’eau La différence de hauteur entre la surface d’appui et l’écoulement de l’eau ne doit pas dépasser 1 mètre. Seuls des tuyaux originaux doivent être utilisés pour une prolongation. (3 m maximum posés sur le sol et jusqu’à 80 cm de hauteur). Le service après-vente dispose de tuyaux d’évacuation de différentes longueurs. Evacuation de l’eau dans un siphon Assurer le point de raccordement bec/siphon avec un collier de serrage (vendu dans le commerce).
Garantie/service-clientèle Servicestellen 5506 Mägenwil/Zürich Industriestrasse 10 9000 St.
www.electrolux.com 36 p t b Albania +35 5 4 261 450 Rr. Pjeter Bogdani Nr. 7 Tirane Belgique/België/ Belgien +32 2 363 04 44 Bergensesteenweg 719, 1502 Lembeek Èeská republika +420 2 61 12 61 12 Budìjovická 3, Praha 4, 140 21 Danmark +45 70 11 74 00 Sjællandsgade 2, 7000 Fredericia Deutschland +49 180 32 26 622 Muggenhofer Str. 135, 90429 Nürnberg Eesti +37 2 66 50 030 Mustamäe tee 24, 10621 Tallinn España +34 902 11 63 88 Carretera M-300, Km.
p t b Slovenija +38 61 24 25 731 Electrolux Ljubljana d.o.o. Gerbiceva 98, 1000 Ljubljana Slovensko +421 2 43 33 43 22 Electrolux Slovakia s.r.o., Electrolux Domáce spotrebièe SK, Seberíniho 1, 821 03 Bratislava Suomi www.electrolux.
Service après-vente En cas de problèmes techniques, vérifiez d’abord s’il ne vous est pas possible de réparer vous-même le dysfonctionnement à l’aide de la notice d’utilisation (chapitre „Que faire, si...“). Si vous ne parvenez pas à réparer le dysfonctionnement, veuillez contacter notre Consumer Services. Pour pouvoir vous dépanner dans les plus brefs délais, nous nécessitons les informations suivantes : – Désignation du modèle – Numéro du produit (PNC) – Numéro de série (S-No.
www.electrolux.com www.aeg.