LAVATHERM 7021 TK ELECTRONIC Kondensationstrockner Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Umwelttipps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Gerätebeschreibung . . . . . . . . . . . . . .
Programmiermöglichkeiten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Verbrauchswerte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Aufstell- und Anschlussanweisung . . . . . . . . . . . . . . . . . . . . . . . 24 Sicherheitshinweise für die Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“ • Vor Inbetriebnahme das Gerät auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten. Bestimmungsgemäße Verwendung • Der Trockner ist nur zum Trocknen haushaltsüblicher Wäsche im Haushalt bestimmt. • Umbauten oder Veränderungen am Trockner sind nicht zulässig.
• Die Abdeckhaube der Glühlampe für die Trommelbeleuchtung muss fest verschraubt sein. Sicherheit von Kindern • Verpackungsteile von Kindern fernhalten. Erstickungsgefahr! • Kinder können Gefahren, die im Umgang mit Elektrogeräten liegen, oft nicht erkennen. Lassen Sie Kinder nicht unbeaufsichtigt beim Trockner. • Stellen Sie sicher, dass Kinder oder Kleintiere nicht in die Trommel des Trockners klettern. Lebensgefahr! Halten Sie die Tür des Trockners geschlossen, wenn er nicht benutzt wird.
2 1 Altgerät Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall zu behandeln ist, sondern an einem Sammelpunkt für das Recycling von elektrischen und elektronischen Geräten abgegeben werden muss. Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Umwelt und Gesundheit werden durch falsches Entsorgen gefährdet.
Gerätebeschreibung Schublade mit Kondensatbehälter Bedienblende Feinsieb (Flusensieb) Lampe für Innenbeleuchtung Grobsieb (Flusensieb) Microfeinfilter (Flusensieb) Typschild Einfülltür (Anschlag wechselbar) Sockeltür vor Wärmetauscher Luftschlitze Schraubfüße (höhenverstellbar) Bedienblende Programmablauf-Anzeige Tasten- und Anzeigenblock 8 Programmwähler Wartungs-Anzeigen – WÄRMETAUSCHER (reinigen!) – BEHÄLTER (leeren!) – SIEB (Flusensiebe reinigen!)
Vor dem ersten Trocknen Um eventuelle fertigungsbedingte Rückstände zu entfernen, Trommel des Trockners mit einem feuchten Tuch auswischen oder kurzen Trockengang (20 MIN) mit feuchten Tüchern durchführen. Wäsche sortieren und vorbereiten Wäsche sortieren • Nach Gewebeart sortieren: – Baumwolle/Leinen für Programme der Programmgruppe BAUMWOLLE. – Mischgewebe und Synthetics für Programme der Programmgruppe MISCHGEWEBE. • Nach Pflegekennzeichen sortieren.
Programmübersicht max. Füllmenge (Trockengewicht) SCHON 1) SIGNAL SENSITIV 1) EXTRATROCKEN 6kg • • • Durchtrocknen von dicken oder mehrlagigen Textilien, z. B. Frotteewäsche, Bademäntel. mn STARKTROCKEN 6kg • • • Durchtrocknen von dicken Textilien, z. B. Frotteewäsche, Frotteehandtücher. mn SCHRANKTROCKEN 6kg • • • Durchtrocknen von Textilien gleichmäßiger Dicke, z. B. Frotteewäsche, Trikotwäsche, Frotteehandtücher.
LEICHTBÜGELN WOLLPFLEGE AUFFRISCHEN SCHON 1) SIGNAL SENSITIV 1) 20 MIN 40 MIN max. Füllmenge (Trockengewicht) Programme Zusatzfunktionen 1kg • • - 1kg 1kg 1kg • • • • • • Anwendung/Eigenschaften Pflegesymbole Zum Nachtrocknen von einzelnen Wäschestücken oder für kleine Mengen unter 1kg. m l2) n - Spezialprogramm mit Anti-Knittermechanik für pflegeleichte Textilien wie Oberhemden und Blusen; für minimalen Bügelaufwand. Ergebnis ist abhängig von Textilart und Textilveredelung.
Trocknen Gerät einschalten/Beleuchtung einschalten Den Programmwähler auf ein beliebiges Programm oder auf BELEUCHTUNG drehen. Das Gerät ist eingeschaltet. Bei geöffneter Einfülltür ist die Trommel beleuchtet. Einfülltür öffnen/Wäsche einfüllen 1. Einfülltür öffnen: Dazu kräftig gegen die Einfülltür drücken (Druckpunkt 2. Wäsche locker einfüllen. 1 ) Achtung! Keine Wäsche zwischen Einfülltür und Gummidichtung einklemmen. 3. Einfülltür fest zudrücken. Schloss muss hörbar einrasten.
SCHON Für besonders schonendes Trocknen empfindlicher Gewebe mit dem Pflegekennzeichen l sowie für temperaturempfindliche Textilien (z. B. Acryl, Viskose). Programm wird mit verminderter Heizleistung ausgeführt. SCHON ist nur bei Füllmengen bis 3kg sinnvoll! SIGNAL Nach Ende des Trockengangs ertönt in Abständen ein akustisches Signal. SENSITIV 3 Für schonendes Trocknen häufig getragener Textilien.
Programm starten Taste START/PAUSE drücken. Das Programm wird gestartet. Die Programmablaufanzeige zeigt den Fortgang der Trocknung an. Programm ändern Um ein versehentlich gewähltes Programm nach Programmstart zu ändern, den Programmwähler zuerst auf AUS drehen und anschließend Programm neu einstellen. 3 Eine direkte Änderung des Programms nach Programmstart ist nicht mehr möglich.
Trockengang beendet/Wäsche entnehmen 3 Nachdem der Trockengang beendet ist, leuchten die Anzeigen ENDE und KNITTERSCHUTZ. Wurde die Taste SIGNAL gedrückt, ertönt in Abständen ein akustisches Signal. An den Trockengang schließt automatisch eine ca. 30-minütige Knitterschutzphase an. Dabei dreht sich die Trommel in Intervallen. So bleibt die Wäsche locker und knitterfrei. Während der Knitterschutzphase kann die Wäsche jederzeit entnommen werden.
1. Einfülltür öffnen 2. Den Microfeinfilter, der im unteren Bereich der Einfüllöffnung eingelassen ist, mit angefeuchteter Hand reinigen. 3. Entriegelungstaste am Grobsieb nach unten drücken. Grobsieb springt auf. 4. Das Feinsieb herausnehmen. 5. Flusen vom Feinsieb entfernen, am besten mit angefeuchteter Hand. 3 16 Gesamten Siebbereich reinigen Der Siebbereich braucht nicht nach jedem Trockengang gereinigt zu werden, sollte aber regelmäßig kontrolliert und gegebenenfalls von Flusen gereinigt werden.
6. Dazu Grobsieb oben anfassen und nach vorn ziehen, bis es sich aus den beiden Halterungen löst. 7. Flusen aus dem gesamten Siebbereich entfernen – am besten mit dem Staubsauger. 8. Beide Zapfen des Grobsiebes in die Halterungen an der Einfülltür drücken, bis sie einrasten. 9. Das Feinsieb wieder einsetzen. 10. Gegen das Grobsieb drücken, bis es in der Verriegelung einrastet. 3 Ohne Feinsieb rastet das Grobsieb nicht ein und die Einfülltür lässt sich nicht schließen. Türdichtung reinigen 1.
3 2. Kondensat in ein Becken oder dergleichen ausgießen. 3. Auslaufstutzen einschieben und Kondensatbehälter wieder einsetzen. Falls das Programm wegen vollem Kondensatbehälter unterbrochen wurde: Taste START/PAUSE drücken, um den Trockengang fortzusetzen. Der Kondensatbehälter fasst ca. 4 Liter, ausreichend für etwa 6kg Wäsche, die vorher bei 800 Umdrehungen/Minute geschleudert wurde. 3 Das Kondensat kann wie destilliertes Wasser verwendet werden, z. B. für Dampfbügeleisen.
5. Wärmetauscher am Griff aus dem Sockel herausziehen und waagrecht transportieren, um zu vermeiden, dass Restwasser ausläuft. 6. Zum Entleeren den Wärmetauscher senkrecht über ein Spülbecken halten. 1 3 Achtung! Zur Reinigung keine spitzen Gegenstände verwenden. Der Wärmetauscher könnte undicht werden. 7. Wärmetauscher reinigen. Am besten eine Handbürste verwenden oder mit einer Handbrause kräftig durchspülen. 8.
Was tun, wenn... Kleine Störungen selbst beheben Falls der Trockner während des Betriebs eine Fehlermeldung anzeigt (eine oder mehrere Anzeigen auf der Programmablauf-Anzeige blinken), prüfen Sie bitte zunächst, ob Sie das Problem mit Hilfe nachstehender Tabelle selbst beheben können. Wenn Sie das Problem nicht beheben können: Gerät aus- und wieder einschalten. Programm neu einstellen. Taste START/PAUSE drücken.
Problem Beim Drücken einer Taste blinkt die zugehörige Anzeige mehrmals Mögliche Ursache Abhilfe Wäscheschutz. Nach Programmstart kann die Zusatzfunktion nicht mehr eingestellt werden. Programmwähler auf AUS drehen. Programm neu einstellen Programmwähler in Stellung AUS. Programmwähler auf BELEUCHTUNG oder auf beliebiges Programm drehen. Lampe defekt. Lampe auswechseln (siehe nachfolgenden Abschnitt). Programm bleibt stehen, Anzeige BEHÄLTER leuchtet. Kondensatbehälter ist voll.
Programmiermöglichkeiten Ziel Akustisches Signal, das an das Programmende erinnert, fest einprogrammieren. Durchführung 1. Programmwähler auf beliebiges Programm drehen. 2. Taste SIGNAL ca. 5 Sekunden gedrückt halten. Kurzes Signal ertönt mehrmals. Anzeige SIGNAL blinkt mehrmals. Damit ist die Einstellung fest einprogrammiert. Einstellung aufheben erfolgt wie unter 1. und 2. 1. Programmwähler auf beliebiges Programm drehen. 2. Die beiden Tasten SIGNAL und SENSITIV gleichzeitig ca.
Technische Daten 5 Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.1973 Niederspannungs-Richtlinie – 89/336/EWG vom 03.05.1989 EMV-Richtlinie einschliesslich Änderungs-Richtlinie 92/31/EWG – 93/68/EWG vom 22.07.1993 CE-Kennzeichnungs-Richtlinie Höhe x Breite x Tiefe 85 x 60 x 60 cm Tiefe bei geöffneter Einfülltür 109 cm Höhenverstellbarkeit 1,5 cm Leergewicht ca. 40kg Füllmenge (programmabhängig) 1) max. 6kg Energieverbrauch nach IEC 1121 s. e.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Vor Inbetriebnahme müssen alle Teile der Transportsicherung entfernt sein. Andernfalls kann das Gerät beschädigt werden. • Vergewissern Sie sich vor Inbetriebnahme, dass die auf dem Typschild des Geräts angegebene Nennspannung und Stromart mit Netzspannung und Stromart am Aufstellort übereinstimmen. Die erforderliche elektrische Absicherung ist ebenfalls dem Typschild zu entnehmen.
Transportsicherung entfernen 1 Achtung! Vor Inbetriebnahme unbedingt alle Teile der Transportsicherung entfernen! Transportsicherung für einen möglichen späteren Transport (Umzug) aufbewahren. 1. Einfülltür öffnen. 2. Klebestreifen innen an der Trommeloberseite abziehen. 3. Folienschlauch mit dem Polystyrolpolster aus dem Gerät ziehen. Elektrischer Anschluss Angaben über Netzspannung, Stromart und die erforderliche Absicherung sind dem Typschild zu entnehmen.
Türanschlag wechseln 1 Warnung! Der Wechsel des Türanschlags darf nur von einem Fachmann ausgeführt werden. Wenden Sie sich bei Bedarf an unseren Kundendienst oder an Ihren Fachhändler. Warnung! Vor Wechsel des Türanschlags Netzstecker ziehen; bei Festanschluss: Sicherung ganz herausdrehen bzw. ausschalten. 1. Einfülltür öffnen. 2. Scharnier A von der Gerätevorderwand abschrauben und Einfülltür abnehmen. 3. Abdeckplatten B und C abnehmen.
7. Abdeckplatten E von der Gerätevorderwand abschrauben, um 180° drehen und auf der gegenüberliegenden Seite anschrauben. 8. Türverriegelung F losschrauben, etwas nach unten drücken und aus der Gerätevorderwand herausnehmen. 9. Den Rastknopf von Abdeckung G unten eindrücken, Abdeckung etwas nach unten drücken und aus Gerätevorderwand herausnehmen. 10. Türverriegelung F auf die gegenüberliegende Seite umsetzen und festschrauben. 11.
Sonderzubehör Über den Ersatzteil-Service oder Ihren Fachhändler ist folgendes Sonderzubehör erhältlich: Zwischenbausätze Wasch-/Trockensäule Mit diesen Zwischenbausätzen kann der Trockner zusammen mit einem AEG-Waschautomaten (60cm breit, Frontbeladung) zu einer platzsparenden Wasch-/Trockensäule angeordnet werden. Der Waschautomat steht unten, der Trockner oben. Zwei Ausführungen sind lieferbar: – ohne Ablageplatte 916.018 902 – mit ausziehbarer Ablageplatte 916.
Kundendienststellen Servicestellen 5506 Mägenwil/Zürich Industriestr. 10 9000 St.
Service Bei technischen Störungen prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können. Wenn Sie das Problem nicht beheben konnten, wenden Sie sich bitte an den Kundendienst oder einen unserer Service-Partner. Um Ihnen schnell helfen zu können, benötigen wir folgende Angaben: – Modellbezeichnung – Produkt-Nummer (PNC) – Serien-Nummer (S-No.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.