LAVATHERM 8040 TW ELECTRONIC Kondensationstrockner mit Wärmepumpe Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Umwelttipps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Gerätebeschreibung . . . . . . . . . . . . . .
Aufstell- und Anschlussanweisung . . . . . . . . . . . . . . . . . . . . . . . 26 Sicherheitshinweise für die Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Gerät transportieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Transportsicherung entfernen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Elektrischer Anschluss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“ • Vor Inbetriebnahme das Gerät auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten. Bestimmungsgemäße Verwendung • Der Trockner ist nur zum Trocknen haushaltsüblicher Wäsche im Haushalt bestimmt. • Umbauten oder Veränderungen am Trockner sind nicht zulässig.
• Benützen Sie das Gerät nicht mit fehlenden oder beschädigten Flusensieben. Brandgefahr! • Den Flusenfilter im Gerätesockel regelmäßig reinigen. • Bei Wasch-/Trockensäulen: Keine Gegenstände auf den Trockner stellen. Diese können während des Betriebs herunterfallen. • Die Abdeckhaube der Glühlampe für die Trommelbeleuchtung muss fest verschraubt sein. Sicherheit von Kindern • Verpackungsteile von Kindern fernhalten.
Entsorgung 2 Verpackungsmaterial Die Verpackungsmaterialien sind umweltverträglich und wiederverwertbar. Die Kunststoffteile sind gekennzeichnet, z. B. >PE<, >PS< etc. Entsorgen Sie die Verpackungsmaterialien entsprechend ihrer Kennzeichnung bei den kommunalen Entsorgungsstellen in den dafür vorgesehenen Sammelbehältern.
2 Umwelttipps • Im Trockner wird die Wäsche flauschig und weich. Weichspüler beim Waschen ist deshalb nicht nötig. • Am wirtschaftlichsten arbeitet der Trockner dann, wenn Sie: – die Lüftungsschlitze am Sockel des Trockners immer frei halten; – die in der Programmübersicht angegebenen Füllmengen ausnutzen; – auf gute Raumbelüftung achten; – Microfeinfilter und Feinsieb nach jedem Trockengang reinigen; – die Wäsche vor dem Trocknen gut ausschleudern.
Gerätebeschreibung Schublade mit Kondensatbehälter Bedienblende Feinsieb (Flusensieb) Lampe für Innenbeleuchtung Grobsieb (Flusensieb) Microfeinfilter (Flusensieb) Typschild Einfülltür (Anschlag wechselbar) Sockeltür vor Flusenfilter und Wärmetauscher Schraubfüße (höhenverstellbar) Luftschlitze Bedienblende Taste RESTFEUCHTE TrockengradAnzeige Multidisplay Taste ZEITVORWAHL Tasten- und Anzeigenblock Programmwähler Programmablauf-Anzeige Wartungs-Anzeigen – BEHÄLTER (leeren!) – SIEB TÜR (Fluse
Programmübersicht max. Füllmenge (Trockengewicht) RESTFEUCHTE KNITTERSCHUTZ + SIGNAL Zusatzfunktionen EXTRATROCKEN 6kg • • • Durchtrocknen von dicken oder mehrlagigen Textilien, z. B. Frotteewäsche, Bademäntel. mn STARKTROCKEN 6kg • • • Durchtrocknen von dicken Textilien, z. B. Frotteewäsche, Frotteehandtücher. mn mn MISCHGEWEBE BAUMWOLLE Programme 10 Anwendung/Eigenschaften Pflegesymbole SCHRANKTROCKEN 6kg • • • Durchtrocknen von Textilien gleichmäßiger Dicke, z. B.
max. Füllmenge (Trockengewicht) RESTFEUCHTE KNITTERSCHUTZ + SIGNAL Zusatzfunktionen 30 MIN 1kg - • • Zum Nachtrocknen von einzelnen Wäschestücken oder für kleine Mengen unter 1kg. ml n 6kg • • • Spezialprogramm für Freizeitkleidung, wie Jeans, Sweat-Shirts, etc., mit unterschiedlichen Materialstärken (z. B. an Bündchen und Nähten). mn FREIZEIT ml n • Spezialprogramm mit Anti-Knittermechanik für pflegeleichte Textilien wie Oberhemden und Blusen; für minimalen Bügelaufwand.
Vor dem ersten Trocknen 1 Wenn das Gerät nicht aufrecht transportiert wurde, lassen Sie es vor Anschluss an das Netz und vor der ersten Inbetriebnahme 12 Stunden stehen, damit das Öl zum Kompressor zurückfließen kann. Andernfalls könnte der Kompressor beschädigt werden. 1. Um eventuelle fertigungsbedingte Rückstände zu entfernen, Trommel des Trockners mit einem feuchten Tuch auswischen oder kurzen Trockengang (30 MIN) mit feuchten Tüchern durchführen.
Trocknen Gerät einschalten/Beleuchtung einschalten Den Programmwähler auf ein beliebiges Programm oder auf BELEUCHTUNG drehen. Das Gerät ist eingeschaltet. Bei geöffneter Einfülltür ist die Trommel beleuchtet. Einfülltür öffnen/Wäsche einfüllen 1. Einfülltür öffnen: Dazu kräftig gegen die Einfülltür drücken (Druckpunkt 2. Wäsche locker einfüllen. ) 1 Achtung! Keine Wäsche zwischen Einfülltür und Gummidichtung einklemmen. 3. Einfülltür fest zudrücken. Schloss muss hörbar einrasten.
Zusatzfunktionen wählen RESTFEUCHTE Zur Feineinstellung des Restfeuchtegehalts der Wäsche können zu den meisten Programmen zusätzlich die Trockenstufen +, ++ oder +++ hinzugewählt werden. Von + zu +++ wird die Wäsche trockener. 1. Die Taste RESTFEUCHTE so oft drücken, bis das Lämpchen der gewünschten Trockenstufe leuchtet. In den Programmen WOLLE oder SEIDE kann bei Bedarf durch erneutes Starten der Programme mit zusätzlich eingestellter Restfeuchtestufe +, ++ oder +++ auch nachgetrocknet werden.
Zeitvorwahl einstellen 3 3 3 Mit der Taste ZEITVORWAHL können Sie den Start eines Programms um 30 Minuten (30') bis max. 23 Stunden (23h) aufschieben. 1. Programm wählen. 2. Taste ZEITVORWAHL so oft drücken, bis der gewünschte Startaufschub im Multidisplay erscheint, z. B. 12h, wenn das Programm in 12 Stunden starten soll. Die Anzeige ZEITVORWAHL leuchtet. Wird 23h angezeigt und Sie drücken ein weiteres Mal, ist die Zeitvorwahl wieder aufgehoben.
Wäsche nachlegen oder vorzeitig entnehmen 1. Einfülltür öffnen. 1 Warnung! Wäsche und Trommel können heiß sein. Verbrennungsgefahr! 2. Wäsche nachlegen oder herausnehmen. 3. Einfülltür fest zudrücken. Schloss muss hörbar einrasten. 4. Taste START/PAUSE drücken, um den Trockengang fortzusetzen. Trockengang beendet/Wäsche entnehmen 3 16 Nachdem der Trockengang beendet ist, leuchten die Anzeigen ENDE und KNITTERSCHUTZ. Wurde die Taste SIGNAL gedrückt, ertönt in Abständen ein akustisches Signal.
Reinigung und Wartung Flusensiebe reinigen 1 Um einen einwandfreien Betrieb des Trockners zu gewährleisten, müssen die Flusensiebe (Microfeinfilter und Feinsieb) nach jedem Trockengang gereinigt werden. Achtung! Den Trockner nie ohne Flusensiebe oder mit beschädigten oder verstopften Flusensieben betreiben. 1. Einfülltür öffnen 2. Den Microfeinfilter, der im unteren Bereich der Einfüllöffnung eingelassen ist, mit angefeuchteter Hand reinigen. 3. Entriegelungstaste am Grobsieb nach unten drücken.
3 Gesamten Siebbereich reinigen Der Siebbereich braucht nicht nach jedem Trockengang gereinigt zu werden, sollte aber regelmäßig kontrolliert und gegebenenfalls von Flusen gereinigt werden. 6. Dazu Grobsieb oben anfassen und nach vorn ziehen, bis es sich aus den beiden Halterungen löst. 7. Flusen aus dem gesamten Siebbereich entfernen – am besten mit dem Staubsauger. 8. Beide Zapfen des Grobsiebes in die Halterungen an der Einfülltür drücken, bis sie einrasten. 9. Das Feinsieb wieder einsetzen. 10.
1. Schublade mit Kondensatbehälter ganz herausnehmen (1) und den Auslaufstutzen des Kondensatbehälters bis zum Anschlag hochziehen (2). 3 2. Kondensat in ein Becken oder dergleichen ausgießen. 3. Auslaufstutzen einschieben und Kondensatbehälter wieder einsetzen. Falls das Programm wegen vollem Kondensatbehälter unterbrochen wurde: Taste START/PAUSE drücken, um den Trockengang fortzusetzen. 3 Der Kondensatbehälter fasst ca.
1. Einfülltür öffnen. 2. Sockeltür öffnen: Dazu Entriegelungstaste an der Unterseite der Einfüllöffnung drücken und Sockeltür nach links aufklappen. 3. Filtergehäuse am Griff aus dem Sockel herausziehen. 4. Türinnenseite, Flusenfiltervorraum und und Gummi-Dichtungen von Flusen reinigen. 5. Flusen vom Flusensieb am Sockelboden mit angefeuchteter Hand entfernen. 6. Zum Reinigen der Filtermatte: Filtermatte aus dem Filtergehäuse entnehmen.
8. Filtermatte in Rahmen einlegen und anschließend mit Rahmen ins Filtergehäuse einsetzen. 1 Achtung! Die Filtermatte muß mit dem Rahmen dicht abschließen. Insbesondere nach Einschieben ins Filtergehäuse den dichten Sitz der Matte am Rahmen prüfen! 9. Nach Bedarf ca. einmal pro Jahr mit dem beiliegenden Schwamm die Flusen vom Wärmetauscher entfernen. Benutzen Sie dazu bitte Haushaltshandschuhe. Tipp: Die Flusen lassen sich leichter entfernen, wenn sie zuvor z. B.
Was tun, wenn... Kleine Störungen selbst beheben Falls während des Betriebs ein Fehlercode (E und Zahl oder Buchstabe) im Multidisplay angezeigt wird: Gerät aus- und wieder einschalten. Programm neu einstellen. Taste START/PAUSE drücken. Wird der Fehler erneut angezeigt, bitte den Kundendienst verständigen und den Fehlercode nennen. Problem Trockner arbeitet nicht. Mögliche Ursache Abhilfe Netzstecker ist ausgesteckt oder Sicherung ist nicht in Ordnung. Netzstecker einstecken.
Problem Mögliche Ursache Abhilfe Anzeige LAUFZEIT verändert sich sprunghaft oder bleibt längere Zeit stehen. Abhängig von Wäscheart, Wäschemenge und Feuchte- Automatischer Prozess, es liegt kein Fehler am Gerät vor. grad erfolgt automatische Korrektur der Laufzeit. Programm bleibt stehen, Anzeige BEHÄLTER leuchtet. Kondensatbehälter ist voll. Trockengang endet kurz nach Programmstart. Anzeige ENDE leuchtet. Zeitprogramm oder höhere Für das gewählte Programm Trockenstufe (z. B.
Programmiermöglichkeiten Ziel Akustisches Signal, das an das Programmende erinnert, fest einprogrammieren. Durchführung 1. Programmwähler auf beliebiges Programm drehen. 2. Taste SIGNAL ca. 5 Sekunden gedrückt halten. Kurzes Signal ertönt mehrmals. Anzeige SIGNAL blinkt mehrmals. Damit ist die Einstellung fest einprogrammiert. Einstellung aufheben erfolgt wie unter 1. und 2. 1. Programmwähler auf beliebiges Programm drehen. 2. Die beiden Tasten SEIDE und SIGNAL gleichzeitig ca.
Technische Daten 5 Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.1973 Niederspannungs-Richtlinie – 89/336/EWG vom 03.05.1989 EMV-Richtlinie einschliesslich Änderungs-Richtlinie 92/31/EWG – 93/68/EWG vom 22.07.1993 CE-Kennzeichnungs-Richtlinie Höhe x Breite x Tiefe 85 x 60 x 60 cm Tiefe bei geöffneter Einfülltür 109 cm Höhenverstellbarkeit 1,5 cm Leergewicht ca. 60kg Füllmenge (programmabhängig) 1) max. 6kg Energieverbrauch nach IEC 1121 s. e.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Vor Inbetriebnahme müssen alle Teile der Transportsicherung entfernt sein. Andernfalls kann das Gerät beschädigt werden. • Vergewissern Sie sich vor Inbetriebnahme, dass die auf dem Typschild des Geräts angegebene Nennspannung und Stromart mit Netzspannung und Stromart am Aufstellort übereinstimmen. Die erforderliche elektrische Absicherung ist ebenfalls dem Typschild zu entnehmen.
Transportsicherung entfernen 1 Achtung! Vor Inbetriebnahme unbedingt alle Teile der Transportsicherung entfernen! 1. Einfülltür öffnen. 2. Klebestreifen innen an der Trommeloberseite abziehen. 3. Folienschlauch mit dem Polystyrolpolster aus dem Gerät ziehen. 1 Wenn das Gerät nicht aufrecht transportiert wurde, lassen Sie es vor Anschluss an das Netz und vor der ersten Inbetriebnahme 12 Stunden stehen, damit das Öl zum Kompressor zurückfließen kann. Andernfalls könnte der Kompressor beschädigt werden.
1. Einfülltür öffnen. 2. Scharnier A von der Gerätevorderwand abschrauben und Einfülltür abnehmen. 3. Abdeckplatten B und C abnehmen. Dazu mit dünnem Schraubendreher entsprechend der Abbildung in die Schlitze einstechen, etwas nach unten drücken und Abdeckplatten heraushebeln. 4. Schließkloben D mit geeignetem Werkzeug durch Druck auf die Rastung lösen, herausnehmen und um 180° gedreht auf der gegenüberliegenden Seite wieder einsetzen. 5.
Sonderzubehör Über den Ersatzteil-Service oder Ihren Fachhändler ist folgendes Sonderzubehör erhältlich: Zwischenbausätze Wasch-/Trockensäule Mit diesen Zwischenbausätzen kann der Trockner zusammen mit einem AEG-Electrolux-Waschautomaten (60cm breit, Frontbeladung) zu einer platzsparenden Wasch-/Trockensäule angeordnet werden. Der Waschautomat steht unten, der Trockner oben.
Kundendienststellen Servicestellen 5506 Mägenwil/Zürich Industriestrasse 10 9000 St.
Service Bei technischen Störungen prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können. Wenn Sie das Problem nicht beheben konnten, wenden Sie sich bitte an den Kundendienst oder einen unserer Service-Partner. Um Ihnen schnell helfen zu können, benötigen wir folgende Angaben: – Modellbezeichnung – Produkt-Nummer (PNC) – Serien-Nummer (S-No.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg-electrolux.