BL14536RBH BL14592RBH BL16536RBHK BL16592BHK CRDH135-92 CRDH145-36 CRDH155-42 CRDH165-107 CRDH180-42 CRDH180-107 MI145HCRD M180HCRD MBA16H107BR MC135TH92RB P145H107RB P18H107RB RE145H92RB RE155H107RB REB145HRB REN145HRB REN145THRB REQ145HRB WZ145H92RB WZ155H107RB WZ18H107RB 135H92RB 165H107RB 02227_PL_LT_CRD Instruction manual Manuel d’instructions Manuale di istruzioni Please read these instructions carefully and make sure you understand them before using this machine.
1 Safety rules. Sicherheitsvorschriften. Règles de sécurité. Reglas de seguridad. Norme antinfortunistiche. Veiligheidsregels. 2 Assembly. Zusammenbau. Montage. Montaje. Montaggio. Montering. 18 3 Functional description. Funktionsbeschreibung. Description du fonctionnement. Descripción del funcionamiento. Funzionamento. Beschrijving van functies. 37 4 Before starting. Maßnahmen vor dem Anlassen. Avant de démarrer. Antes del arranque. Prima dell’avviamento. Maatregelen vóór het starten.
1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. Training III. Operation • Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. • Never allow children or people unfamiliar with the instructions to use the lawnmower.
• • Stop the engine and disengage drive to attachment - before refueling; - before removing the grass catcher; - before making height adjustment unless adjustment can be made from the operator’s position. Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing. IV. Maintenance and Storage • • • • • • • • • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.
1. Sicherheitsvorschriften Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN. I. SCHULUNG • • Die Anleitungen sorgfältig durchlesen. Mit den Bedienungselementen und der vorschriftsmäßigen Bedienung der Maschine vertraut machen.
• • • • • Vor dem Verlassen der Bedienungsstation: - Die Zapfwelle abstellen und alle Anbaugeräte absenken. - In Leerlauf schalten und die Feststellbremse einlegen. - Den Motor abstellen und den Zündschlüssel abziehen. Alle Anbaugeräte-Antriebe ausschalten, den Motor abstellen und das (die) Zündkerzenkabel abziehen bzw.
1. Règles de Sécurité Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS.L’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES. • I. PRÉCAUTIONS D’UTILISATION • Lisez toutes les instructions soigneusement. Familiarisez vous avec les commandes pour appprendre à utiliser efficacement cette machine.
• Avant de quitter le siége : - débrayer les lames et abaisser le carter de coupe, - mettre le levier de vitesse au point mort et enclencher le frein de parking, - arrêter le moteur et retirer les clés, • Débrayer les lames, arrêter le moteur, et débrancher le (s) fil (s) de (s) bougie (s) d’allumage ou retirer la clef de contact : - avant de retirer l’insert broyeur ou avant de retirer la goulotte d’éjection pour la nettoyer.
1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. I. INSTRUCCIÓN • • Lea todas las instrucciones cuidadosamente.
• • • • Desenganche la transmisión a los accesorios, pare el motor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora; - después de golpear un objeto extraño.
1. Norme Antinfortunistiche Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. I. ADDESTRAMENTO ALL’USO • • Studiare attentamente le istruzioni. Acquisire dimestichezza con i comandi e conoscere a fondo l’uso corretto dell’equipaggiamento.
• • • • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele oppure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e prima di stasare lo scivolo; - prima di interventi o controlli sul tosaerba e prima delle operazioni di pulizia; - dopo aver colpito un oggetto estraneo.
1. Veiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. I. TRAINING III. BEDIENING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken.
• • • - nadat u een ongewenst voorwerp heeft geraakt. Inspecteer de maaimachine op schade en voer reparaties uit voordat u de machine weer start en gebruikt; - als de machine abnormaal begint te trillen (onmiddellijk controleren). - vor dem Entfernen von Verstopfungen aus dem Mähwerk oder dem Auswurf; Schakel de aandrijving naar de hulpstukken uit tijdens transport of als ze niet worden gebruikt.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent se montrer sur votre machine ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
01738 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLETZUNGEN VERURSACHEN. ZU VERMEIDEN: • FUNKEN • FEUER • RAUCHEN SCHWEFELSÄURE KANN ERBLINDUNG ODER SCHWERE VERÄTZUNGEN VERURSACHEN. AUGEN UNVERZÜGLICH MIT WASSER AUSSPÜLEN. SOFORT ÄRZTLICHE HILFE AUFSUCHEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. GEEN • VONKEN • VUUR • ROKEN ZWAVELZUUR KAN BLINDHEID OF ERNSTIGE BRANDWONDEN VER-OORZAKEN. OGEN ONMIDDELLIJK MET WATER SPOELEN.
2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montage. Before the tractor can be used certain parts must be assembled, which for transportation reasons are enclosed in the packing. Antes de poder utilizar el tractor, hay que montar algunas piezas que, por razones de transporte, van empaquetadas en el embalaje. Vor der Anwendung des Aufsitzmähers müssen gewisse Teile eingebaut werden, die aus Transportgründen in der Verpack-ung lose beigefügt sind.
2 VOLANTE VOLANT DE DIRECTION • • • • • • Monter la rallonge de l'arbre de direction (1) en alignant bien les trous. Bien serrer la vis et l'écrou. Positionner le carénage sur la colonne de direction. S'assurer que les ergots du carénage sont bien placés dans les trous correspondants du tableau de bord. Retirer l'adaptateur cranté du volant et le glisser sur l'arbre de direction. Vérifier que les roues avant sont bien alignées selon l'axe d'avancement et positionner le volant sur l'adaptateur.
2 1 2 02701 02617 02466 1 Zitting Verwijder de bevestigingselementen waarmee de zitting aan de kartonnen verpakking bevestigd is en zet deze bevestigingselementen opzij voor het monteren van de zitting op de trekker. Draai de zitting omhoog en haal hem uit de kartonnen verpakking. Verwijder de kartonnen verpakking en werp die weg. Plaats de stoel op de zitpan zodat de kop van de borstbout zich over het grote sleufgat in de pan bevindt (1).
2 1. 2. 3. 4. 5. 6. Battery Cover Cable Positive (+) Cable Negative (-) Fender Battery terminal Battery 1. 2. 3. 4. 5. 6. Batterieabdeckung Positives Kabel (+) Negatives Kabel (-) Schutzblech Batterieklemme Batterie 1. Capotage de batterie 2. Câble (+) 3. Câble (-) 4. Carrosserie 5. Borne de la batterie 6. Batterie 1. Tapador del acumulador 2. Cable positivo (+) 3. Cable negativo (-) 4. Protección 5. Terminal de batería 6.
2 WARNING: Positive terminal must be connected first to prevent sparks from accidental grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth cable to -. Screw tight the cables. Grease the battery poles with vaseline to prevent corrosion. Replace battery cover. WARNUNG! Um einen Kurzschluß zu vermeiden, muß der Pluspol zuerst angeschlossen werden. Die Schutzkappen von den Anschlußklemmen entfernen und entsorgen. Die Batterie in Position neben den Fahrersitz bringen.
2 PARA AJUSTAR LAS RUEDAS CALIBRADORAS (si está provisto) Las ruedas calibradoras están bien ajustadas cuando se encuentran un poco a distancia del terreno al mismo tiempo que la segadora esté a la altura de corte deseada. Entonces las ruedas calibradoras mantienen el conjunto segador en posición para prevenir el corte raspeo en casi todos los terrenos. • Ajuste las ruedas calibradoras con el tractor en una superficie nivelada plana.
2 To install bagger components to tractor 3 1 2 02 2 Support Bracket 3/8 Carriage Bolt 1 3/8 Lock Nut 3/8 x 63,5mm Hex Bolt 10,3mm (13/32") flat washer • Install the two upper support brackets through the back plate and to the chassis, using the 10 x 19 mm (3/8"x3/4") carriage bolts and locknuts supplied. Tighten securely. Assemble both support brackets to the outside of the baggger support tube using two each 3/8 x 63,5mm hex bolts13/32" I.D. flat washers and 3/8 locknuts from parts bag.
2 1 2 To Assemble Bagger NOTE: For ease of assembly, you may wish to obtain the assistance of another person when putting the bagger together. • Holes in front bagger tube are at an angle. Place front bagger tube against lower bagger tube and check for proper hole alignment before assembling bolts. • Assemble front and lower bagger tubes using four (4) 1/4 x 50,8mm carriage bolts and lock nuts supplied. Tighten securely. • Slide front and lower bagger tube assembly into the bagger assemby.
2 Installation der Aufhängung der Grasfangbox des Traktors 3 1. 2. 3. 4. 1 1. Auswurfkanal 2. Kontermutter 3/8 3. Flache unterlegscheibe 2 02 5 4 2 02590 Strebe Tragbolzen 3/8 3 Kontermutter 3/8 Sechskantbolzen 1 3/8 x 63,5mm 5. Flache Unterlegscheibe 10,3mm (13/32) 27 7 3 • • • Nehmen Sie den Auswurfkanal aus dem hinteren Teil des Traktors. Lösen Sie beide (2) Klammern und ziehen Sie den Kanal aus dem Traktor.
2 1 Montage der Grasfangbox 2 HINWEIS: Zum leichteren Zusammenbau der Grasfangbox ist es u.U. sinnvoll, die Hilfe einer zweiten Person heranzuziehen. • Die sich vorne in der Absackröhre befindlichen Löcher sind schräg angesetzt. Die vordere Absackröhre an der unteren Absackröhre anlegen und ausrichten und vor der Montage der Bolzen die genaue Ausrichtung der Löcher überprüfen.
2 Assemblage des composants du collecteur 3 1 1 1. Goulotte d'éjection 2. Ecrou 3/8 3. Rondelle plate • • 02 2 77 Bras support supérieur 4 2 Boulon poêlier 3/8 Ecrou frein 3/8 Vis H 3/8 x 63,5 Rondelle plate diam. 10,3 mm (13/ 32") • Positionner les deux bras supports supérieurs à travers le panneau arrière du tracteur et les fixer au châssis à l'aide des boulons poêliers de 3/8 x 3/4" et des écrous fournis. Serrer à fond.
2 Pour assembler le collecteur 1 REMARQUE : nous vous recommandons, pour plus de facilité, de vous faire aider d’une autre personne pour effectuer le montage du collecteur. • Les trous dans l’armature frontale du collecteur sont percés avec un angle prédéterminé. Lorsque vous mettez l’armature frontale en position d’assemblage contre l’armature inférieure (voir dessin ci-contre) vérifiez le bon alignement des trous avant de placer les boulons.
2 Para montar los componentes del contenedor para costales al tractor 3 1 3 1 1. Descarga de adaptarse 2. Tuercas de 3/8 3. Arandelas planas • • 02 2 77 5 4 Consola portadora tornillo portadora 3/8 Contratuerca 3/8 3/8x63,5mm arandelas planas Arandela plana 10,3mm (13/ 32î) • Instale los dos soportes superiores a través de la placa posterior al chasis, usando los pernos de acarreo de 10 x 19 mm (3/8" x 3/4"), y las tuercas de seguridad provistos. Apretar bien.
2 1 Para montar el contenedor 2 NOTA: Para facilitar el ensamblaje de la recolectora dehierba,se aconseja efectuar las operaciones con de la ayuda de otra persona. • Los agujeros del tubo delantero del recogedor del césped están en ángulo. Coloque el tubo delantero del recogedor del césped contra el tubo más inferior y verifique la alineación apropiada de los agujeros antes de ensamblar los pernos.
2 Per montare i componenti del cesto di raccolta 3 1 3 1 1. Convogliatore di scarico 2. Dadi 3/8 3. Rondella Piatta • • 02 2 77 3 • Rimuovere il convogliatore dalla parte posteriore del trattore. Allentare le due graffe, sganciare ed estrarre il convogliatore. Rimuovere i due (2) dadi da 3/8 e le rondelle piatte dai bulloni sulla piastra posteriore del trattore. • 5 4 Staffa di supporto 2 Bullone di supporto (3/8) Dadi 3/8 Bullone a testa esagonale (3/8 x 63,5mm) Rondella piatta 02590 1. 2. 3.
2 1 Per montare il cesto di raccolta: NOTA: per facilitare l’assemblaggio, nell’installare il sacco può essere utile farsi aiutare da un’altra persona. • I fori del tubo bagger frontale sono posti ad angolo. Posizionare il tubo bagger frontale contro il tubo bagger inferiore e, prima di inserire le viti, controllare che i fori siano allineati.
2 3 Hetmonteren van componenten van de grascontainer op de trekker 3 1 1. Afvoertrechter 2. 3/8 borgmoer 3. Vlakke sluitring • • 02 2 1 Stennijzer 5 4 3/8 Slotbout 3/8 borgmoer 3/8 Zeskantbout Vlakke sluitring 10,3 mm (13.32") • Bevestig de twee bovenste steunbeugels door de achterplaat en aan het frame. Gebruik hiervoor de bijgeleverde slotschroeven en borgmoeren van 10 x 19 mm (3/8" x 3/4"), en draai deze goed vast.
2 1 2 De grascontainer monteren N.B.: Indien gewenst kunt u de grascontainer samen met iemand anders in elkaar zetten om het assembleren makkelijker te maken. • De gaten in de voorste toevoerslangen voor de zak zijn schuin aangebracht. Plaats de voorste slang tegen de onderste slang en controleer of de gaten goed op één lijn liggen voordat u de moeren aanbrengt.
2 1 2 A 3 A 4 1. 2. 3. 4. Handle Retainer Spring Pin Plug 1. 2. 3. 4. Mango Resorte fijador Clavija Tapon o tapa 1. 2. 3. 4. Handgriff Fixierfeder Stift Stöpsel 1. 2. 3. 4. Impugnatura Coppiglia Perno Kit Mulching 1. 2. 3. 4. Poignée de l'insert Epingle Axe de fixation Tête de l'insert 1. 2. 3. 4. Hendel Sluitveer Pen Plug To assemble and install mulcher plug (if equipped) • • • Para ensamblar y montar la tapa mulching (si está provisto) Remove spring retainer and pin from handle.
3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies 5 1 7 10 3 6 8 2 4 9 Positioning of controls 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Anordnung der Bedienungseinrichtungen Light Switch Position. Throttle control. Brake and clutch pedal. Motion Control Lever. Connection/disconnection of the cutting unit. Quick lifting/lower of the cutting unit. Ignition lock. Parking Brake.
3 5 1 7 10 3 6 8 2 4 9 Comandi Emplacement des commandes 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Interrupteur de commande des phares. Commande des gaz (Accélérateur). Pédale d'embrayage et de frein. Levier de commande dela transmission hydrostatique. Embrayage/débrayage du carter de coupe. Relevage et abaissement du carter de coupe. Clé de contact/démarrage. Frein de parking. Blocage/déblocage de la roue libre. Starter. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Ubicación de los mandosè 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
3 1. Light switch position (if equipped) 1. Lichtschalter (sofern vorhanden) 1. Interrupteur des phares (si équipé) 1. Interruptor de alumbrado (si está provisto) 1. Interruttore luci (se installato) 1. Schakelaar verlichting (indien hiermee uitgerust) 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2. Gashebel Mit dem Gashebel wird die Drehzahl des Motors und damit die Drehgeschwindigkeit des Mähaggregats geregelt.
3 3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abgebremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus. 01 3. Pédale d'embrayage et de frein 35 8 En appuyant sur cette pédale, la transmission se débraye et le frein entre en action simultanément. 3.
3 4. Levier de commande de la transmission hydrostatique Le levier peut être placé dans quatre positions différentes : N = Position neutre S = Vitesse lente F = Vitesse rapide R = Marche arrière Le levier peut être déplacé progressivement de S à F afin d'obtenir la vitesse désirée. S F R 4.
3 5. Commande d'embrayage et de débrayage du carter de coupe Pousser le levier vers l'avant et le verrouiller pour embrayer le carter de coupe. Les courroies d'entraînement seront alors en tension et les lames commenceront à tourner. Ramener le levier vers l'arrière pour débrayer le carter de coupe, les lames seront alors freinées par le frottement des patins de frein sur les poulies d'entraînement. 5.
3 01949 OFF ON START 7. Cerradura de encendido 7. Ignition Lock La llave de encendido puede hallarse en tres posiciones diferentes: OFF Corriente eléctrica cortada ON Corriente eléctrica conectada START Motor de arranque acoplado ADVERTENCIA! Si abandona la máquina sin vigilancia, no deje nunca la llave en la cerradura. There are three different positions for the ignition key: OFF All electric current broken. ON Electric current connected. START Start motor connected.
3 8. Frein de stationnement 01 Pour enclencher le frein de stationnement : 1. Enfoncer à fond la pédale d'embrayage/frein. 2. Relever vers le haut le levier du frein de stationnement et le maintenir dans cette position. 3. Relâcher la pédale d'embrayage/frein. Relâcher le levier du frein de stationnement qui restera dans sa position verrouillée (en haut).
3 10. Starter Lorsque le moteur est froid, tirer le bouton de commande du starter avant d'essayer de démarrer. Dès que le moteur a démarré et tourne régulièrement, repousser le bouton de commande. 3 36 01 10. Estrangulador Cuando el motor está frio, extraer el estrangulador antes deintentar el arranque. Cuando ha arrancado el motor y funciona con regularidad, introducir el estrangulador. 10. Choke 10.
4. Before starting. 4. Maßnahmen vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Reposición de combustible Filling up The engine should be run of pure (not oil mixed) unleaded petrol. Do not fill beyond the lower edge of the filling hole. Do not fill over max level. El motor ha de funcionar con gasolina pura (sin mezcia de aceite), sin plomo. El nivel no ha de sobrepasar el borde inferior del orificio de llenado.
4 Nivel de aceite Oil level La tapa combinada para el llenado de aceite y para la varilla de nivel queda accesible después de haber levantado hacia adelante el capó del motor. El nivel de aceite del motor debe controlarse cada vez que se pone en marcha. Asegúrese de que la máquina está horizontal. Descenrosque la varilla y séquela. Vuélvala a colocar. Enrósquela. Quítela otra vez y lea el nivel de aceite. The combined oil refilling cap and the oil stick is accessible when the bonnet is lifted forwards.
4 Tire air pressure Check the tire pressure regularly. The pressure in the front tires should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires. Reifendruck Den Luftdruck in den Reifen regelmäßig prüfen. Der Druck in den Vorderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar. Pression de gonflage des pneus Vérifier régulièrement la pression de gonflage des pneus. La pression de l'air dans les pneus doit être de 1 bar pour les roues avant et de 0,8 bar pour les roues arrières.
5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Démarrage du moteur S'assurer préalablement que le carter de coupe est en position de transport (c'est à dire : relevé au maximum) et que le levier d'embrayage et de débrayage du carter de coupe est en position "débrayée" (voir figure).
5 Bei warmem Motor: Gashebel in die Vollgasstellung " schieben. " Si le moteur est chaud : pousser la commande des gaz à mi-distance de sa position d'accélération maximale. " ". Moter caliente: Empuje el acelerador hasta la mitad de su recorrido hacia la posición de plenos gases " ". Motore caldo: Portare il comando del gas sul massimo " ". Bij een warme motor: Schuif de gashendel halverwege naar de volgaspositie " ". Warm motor: Push the gas control half-way to full gass position " ".
5 • IMPORTANT! COLD STARTING FOR HYDRO COLD STARTING FOR HYDRO (BE LOW 40°F [4°C]) - AFTER STARTING ENGINE AND BEFORE DRIVING, LET TRANSMISSION WARM UP FOR ONE (1) MINUTE BY PLACING MOTION CONTROL LEVER IN NEU TRAL (N) POSITION AND RELEASING CLUTCH/BRAKE PEDAL. • • • • WICHTIG! KALTSTARTEN FÜR MASCHINEN MIT HYDROSTATISCHEM GETRIEBE FÜR TEMPERATUREN UNTERHALB VON 40° (4°C). NACH DEM ANLASSEN DES MOTORS DAS GETRIEBE (1) MINUTE LANG AUFWÄRMEN LASSEN, BEVOR LOSGEFAHREN WIRD. HIERZU DAS SCHALTGETRIEBE IN.
5 • • • • • • • • • • SPURGO DELLA TRASMISSIONE Placer le tracteur sur une surface plane afin qu'il ne puisse pas rouler dans aucune direction. Le frein de stationnement doit être desserré pour effectuer les opérations suivantes. Débrayer la transmission en plaçant la commande de roue libre sur sa position de marche en roue libre (Se référer à la section "TRANSPORT" de ce livret). Démarrer le moteur et mettre la commande des gaz en position de ralenti.
5 NOTE! NOTA! The machine is equipped with a safety switch which immediately breaks the current to the engine if the driver leaves the seat with engine running and with the connection/disconnection lever in position “connection”.Your machine is also equipped with a system that will not allow mower to operate if the bagger or optional rear discharge deflector is not installed properly.
5 Cutting tips • • • • • • • • Clear the lawn from stones and other objects which can be thrown away by the blades. Localize and mark stones and other fixed objects to avoid collision. Begin with a high cutting height and reduce until the required cutting result is obtained. The cutting result is best with high engine speed (blades rotate quickly) and low gear (machine goes slowly).
5 Pour vider le bac: Votre tracteur est équipé d'une alarme sonore qui vous avertit lorsque le bac est plein. Pour arrêter l'alarme, débrayer les lames. • Amener le tracteur là ou vous souhaitez le décharger. • Mettre le levier de boîte de vitesses au point mort et tirer le frein à main. • Tirer le leiver de vidange du bac vers le haut puis vers l'avant afin d'ouvrir le bac et vider l'herbe coupée. • Remettre ensuite le levier dans sa position initiale.
5 To convert mower • • (Converting to mulching or rear discharging will require the purchase of these accessories.) • To mulching • Place deck into the high cut position. • Remove bagger or optional rear discharge deflector. • Unhook the two (2) straps and remove discharge chute. • Insert plug and handle assembly through back plate and onto the mower deck chute adaptor. • Retain the plug assembly by connecting the two straps over the handle and hook into the holes provided.
5 Per lo scarico a terra Mettere il piatto nella posizione piu' alta. Togliere il cesto e il Kit Mulching Installare il deflettoreper lo scarico a terra nell' apposita apertura della piastra posteriore. • Agganciare il deflettore con le due graffe, inserite nelle aperture della piastra. • Stringere le quattro viti nei fori filettati che si trovano sulla piastra posteriore. • Serrare saldamente le viti.
5 ATTENTION! • • • Ne jamais utiliser un tracteur sur des pentes excédant 10°. Les risques de renversement étant alors très importants. Ne jamais rouler parallèlement à la pente du fait des risques de renversement. Toujours rouler perpendiculairement à la pente, aussi bien en montant, qu'en descendant. Ne jamais arrêter ou démarrer un tracteur en pente. ADVERTENCIA! • • • WARNING! • • • PERICOLO! Do not drive in terrain at an angle of more than max. 10°. The risk for spark-over backwards is large.
5 Switching off the engine Move the gas control to “ ”. Disconnect the cutting unit by moving the connect/disconnect lever downwards. Lift up the cutting unit and turn the ignition key to “OFF” position. Allow the engine to idle for 1-2 minutes to cool down before switching off after a hard work. Abstellen des Motors Gashebel nach unten auf “ ” führen. Mähaggregat durch Abwärtsführen des Aggregatschalthebels auskuppeln. Mähaggregat anheben und den Zündschlüssel auf “OFF” drehen.
6. Maintenance, adjustment. 6. Wartung (Instandhaltung), Einstellung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! ADVERTENCIA! Antes de proceder a efectuar el servicio en el motor o en el equipo de corte, hay que hacer lo siguiente: • Apretar el pedal del embrague/freno y acoplar el freno de estacionamiento. • Poner la palanca de cambios en punto neutro. • Poner la palanca de embrague en posición desembragada. • Parar el motor.
6 Engine hood • • • • 1 • Raise hood. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt forward and lift off of tractor. To reinstall, slide hood pivot brackets into slots in frame. Reconnect headlight wire connector and close hood. Motorhaube • • • • 01536 • Motorhaube hochklappen. Scheinwerferanschluß lösen. Vor den Mäher treten. Motorhaube an den Seiten anfassen, nach vorn kippen und aus dem Mäher herausheben.
6 Maintenance Mantenimiento NOTE: Periodic maintenance should be performed on a regular basis in order to keep your tractor in good running condition. WARNING: Disconnect spark plug wire to prevent accidental starting before attempting any repair, inspection, or maintenance. Before each use: • Check oil, lubricate pivot points as necessary. • Check to see all bolts, nuts, and cotter pins are in place and secure. • Check the battery, terminals and vents. • Recharge slowly at 6 amperes if needed.
6 Pour assurer l'entretien du moteur Se référer au manuel d'utilisation du moteur. Vidange de l'huile du moteur Retirer le bouchon (1) et placer le tuyau de vidange (2). Pour ouvrir la soupape de vidange, repousser légèrement la soupape en la faisant tourner dans le sens contraire des aiguilles d'une montre pour sortir du cran, puis tirer sur la soupape pour libérer l'huile.
6 SERVICE RECORD Fill in dates as you complete regular service As Needed Every 8 hours Every 25 hours Change engine oil (without oil filter) ................................................... Every. 50 hours • Change engine oil (with oil filter) ............................................................................ Lubricate pivot points ......................................................................... Check brake operation ................................ • • Every.
6 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Selon les besoins Toutes les 8 H Toutes les 25 H Vidange de l'huile moteur Toutes les 50 H Toutes les 100 H Toutes les 200 H • (sans filtre à huile) .................................................................................... Vidange de l'huile moteur (avec filtre à huile) .........................................................................................................
6 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni 8 ore Ogni 25 ore Cambio dell'olio (Senza filtro dell’olio)................................................ Ogni . 50 ore • Cambio dell'olio (Con filtro dell’olio) ....................................................................... Lubrificazione punti di articolazione ................................................... Controllo freni.............................................. • Pulizia schermo aria....
6 Blades Lames: The blades should be sharp to achieve best cutting results. Sharpening can be carried out with a file or grinding disc. NOTE: It is very important that both blades are sharpened equally to avoid imbalance. Les lames doivent être parfaitement affûtés pour obtenir une belle coupe. L'affûtage peut être réalisé à l'aide d'une lime ou d'une meule. REMARQUE: Il est très important d'affûter les deux extrémités de la lame de façon identique afin d'éviter tout déséquilibrage.
6 8 7 8 7 (If equipped) (sofern vorhanden) (si équipé) LH 02051 3 3 6 1 LH 6 1 5 5 4 2 2 4 1. Hex bolt right hand threaded. 2. Lock Washer 3. Flat Washer 4. Blade 5. 6. 7. 8. 1. Sechskantschraube mit Rechtsgewinde 2. Federscheibe 3. Flache Unterlegscheibe 4. Schneidmesser 5. Fünfeckige Zentrierbohrung 6. Fünfeckige Messeraufnahme 7. Hintere (Hilfsschneid-) Kante 8. Messeraufnahme komplett 1. Boulon de type hexagonal avec filetage à droite 2. Circlips 3. Rondelle plate 4. Lame 5.
6 8 7 8 7 (si está provisto) (se installato) (indien hiermee uitgerust) LH 3 02051 6 1 3 5 LH 1 6 5 2 4 4 2 1. Tornillo de cabeza de cinco facetas, dextrogiro 2. Arandela elastica 3. Arandela plana 4. Filo cortador 5. Orifico de centrajeestrella de cinco puntas 6. Mandril-estrella de cinco puntas 7. Canto (auxiliar cortador) trasero 8. Nudo del mandril 1. Bullone a testa esagonale con filettatura destrorsa 2. Rondella elastica 3. Rondella piatta 4. Lama 5.
6 For best results mower blades must be kept sharp. Replace bent or damaged blades. BLADE REMOVAL • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and flat washer securing blade. • Install new or resharpened blade with trailing edge up towards deck as shown. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. • Reassemble hex bolt, lock washer and flat washer in exact order as shown.
6 X 1. Measure the distance between the brake lever and the adjuster nut (X). 2. Yellow Spring - The distance should be 43mm (1.68"). Green Spring - The distance should be 40mm (1.56"). 3. Adjust the distance if necessary by first loosening the lock nut (2) and then adjusting with the nut (1). 2 1. Abstand zwischen Bremshebel und Stellmutter messen (X). 2. Gelber Federstecker - Der Abstand soll 43mm betragen. 1 Grüner Federstecker - Der Abstand soll 40mm betragen. 3.
6 Dismantling of the cutting unit 2 Work from the right side of the machine. 1. Take off the belt from the engine pulley (1). 2. Remove the two rear retainer springs (2) and knock off the axle taps with a hammer. 1 Demontage des Mähdecks Arbeiten Sie auf der rechten Seite der Maschine. 1. Entfernen Sie den Riemen von der Keilriemenscheibe des Motors (1). 2. Entfernen Sie die beiden hinteren Federklammern (2) und entfernen Sie die beiden Bolzen.
6 3 4 5 Assembly of the cutting unit 3. Remove the retainer springs (3), (4), (5) and axles. 4. Pull the lever for lifting/lowering the cutting unit backwards. 5. Pull out the cutting unit from the machine. • • Push in the cutting unit under the machine. Assemble in the reverse order to dismantling. Einbau des Mähdecks • • 3. Die Federklammern (3), (4), (5) und die jeweiligen Bolzen ausbauen. 4. Hebel für Heben/Senken des Mähdecks zurückziehen. 5. Mähdeck aus ber Maschine herausziehen.
6 Remplacement de la courroie d'entraînement du carter de coupe 1. Déposer le carter de coupe (voir chapitre précédent). 2. Sortir la courroie d'entraînement des gorges de poulie en commençant par la poulie du côté gauche du carter de coupe, puis par les autres poulies. 3. Retirer ensuite entièrement la courroie du carter de coupe. 4. Pour la mise en place de la nouvelle courroie, procéder dans l'ordre inverse. Vérifier que la courroie est correctement positionnée devant tous les guides de courroie.
6 2 A 1 B Adjustment of the cutting unit 1. 2. 3. 4. A. In the direction of travel Check that the air pressure is correct in all four tires. Make sure that the machine is on a horizontal surface. Lift up the cutting unit to its highest position. Measure the distances A and B. To achieve best cutting results the cutting unit’s front edge (B) should be about 10 mm (0.375") lower than the back edge (A). Adjust in the following way to raise the back edge: 1.
6 REGLAGE TRANSVERSAL 1 • • Relever le carter de coupe au maximum. A partir du milieu de chaque extrémités latérales du carter de coupe, mesurer la distance du bord du carter par rapport au sol . • La distance (A) doit être la même des deux côtés à 6 mm près. • Si un réglage est nécessaire, ne l'effectuer que d'un seul côté en se référant à l'autre côté. • Abaisser ou soulever un côté du carter de coupe en ajustant la position de l'écrou de réglage de ce côté.
6 Cambio de correa propulsora 1. Desmontar el equipo de corte del tractor. 2. Desmontar el limitador de movimientos del acoplamiento (1). 3. Aplicar el freno de estacionamiento y tirar hacia arriba de la correa para sacarla de la rueda libre (2), de la acoplamiento (3). 4. Introducir la correa entre dos aspas del ventilador y hacer girar éste a izquierdas hasta que queda libre la correa (4). 5. Quitar después la correa de la polea del motor (5). 5 2 Sostituzione della cinghia di trazione 3 1.
6 EINSTELLUNG DES STEUERKNÜPPELS DES SCHALTGETRIEBES 1 Der Steuerknüppel wird von der Herstellerfirma im Werk voreingestellt und erfordert daher in der Regel keine weiteren Einstellungen. • Den vorne auf dem rechten Hinterrad befindlichen Einstellbolzen lösen und wieder leicht anziehen. • Den Motor anlassen und den Steuerknüppel verschieben, bis sich der Traktor weder vorwärts noch rückwärts bewegt. • Den Steuerknüppel in dieser Stellung lassen und den Motor ausschalten.
6 REGOLAZIONE DELLA LEVA DI COMANDO DEL MOVIMENTO DEL MECCANISMO DEL CAMBIO 1 La leva di comando del movimento del meccanismo del cambio è stata impostata al momento della fabbricazione e non richiede pertanto ulteriori regolazioni. • Allentare il bullone di regolazione di fronte alla ruota posteriore destra; stringendolo poi leggermente. • Avviare il motore e spostare la leva di comando del meccanismo del cambio finché in trattore non si muove avanti o indietro.
6 TRANSAXLE COOLING ENFRIAMIENTO DEL TRANSEJE The fan and cooling fins of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. Las aletas de enfriamiento y el ventilador de la transmisión tienen que mantenerse limpios para asegurar el enfriamiento adecuado.
7. Troubleshooting. 7. Störungssuche. Motor springt nicht an Engine will not start 1. 2. 3. 4. 1. 2. 3. 4. No fuel in fuel tank. Plug defective. Plug connection defective. Dirt in carburetor or fuel pipe. Anlasser dreht den Motor nicht durch Start motor will not turn engine 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. Battery flat. Poor contact between cable and battery pole. Connection/disconnection level in wrong position. Main fuse defective. Ignition lock defective.
7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne démarre pas 1. Manque de carburant dans le réservoir. 2. Bougie d'allumage défectueuse. 3. Le câblage de la bougie d'allumage défectueux. 4. Il y a des impuretés dans le carburateur ou dans le circuit du carburant. El motor no arranca 1. 2. 3. 4. Le démarreur n'entraîne pas le moteur 1. La batterie est déchargée. 2. Mauvais contact entre les cosses des câbles de batterie et les bornes de la batterie. 3.
7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. 2. 3. 4. De motor start niet Manca il carburante. Difetto di candela. Collegamento della candela difettoso. Sporco nel sistema di alimentazione e o nel carburatore. 1. 2. 3. 4. De startmotor trekt de motor niet Il motorino di avviamento non fa girare il motore 1. 2. 3. 4. 5. 6. De accu is leeg. Slecht contact tussen kabel en accupool. Aan/uitschakelhendel in foutieve stand. De hoofdzekering is defect.
8. Storage. 8. Aufbewahrung. 8. Remisage. 8. Conservación. The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cutting unit cover. Do not use high pressure washer for cleaning. Water can enter engine and transmission and shorten the useful life of the machine. • Touch up all chipped paint surfaces in order to avoid corrosion. • Change engine oil. • Drain the fuel tank. Start the engine and allow it to run until it is out of fuel.
8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti interventi: • Pulire tutto il tagliaerba e particolarmente sotto il coperchio della falciatrice. Per le operazioni di pulizia, non utilizzare acqua ad alta pressione. L’acqua può infiltrarsi nel motore e nel sistema di trasmissione, riducendo quindi così il tempo di vita della macchina. • Ritoccare danni alla verniciatura per evitare ossidazione. • Cambiare l’olio del motore. • Vuotare il serbatoio della benzina.
02703 EN 1032 8 EN 1033 4 BL14536RBH 14,5/10,8 0-7,3 92 38-102 235 BL14592RBH 14,5/10,8 0-7,3 92 38-102 235 BL16536RBHK 16,5/12,3 0-7,3 92 38-102 235 BL16592BHK 16,5/12,3 0-7,3 92 38-102 235 MI145HCRD 14,5/10,8 0-7,3 107 38-102 235 M180HCRD 18/13,4 0-7,3 107 38-102 235 16/12 0-7,3 107 38-102 235 MC135TH92RB 13,5/10,1 0-7,3 92 38-102 235 P145H107RB 14,5/10,8 0-7,3 107 38-102 235 P18H107RB 18/13,4 0-7,3 107 38-102 235 14,5/10,8 0-7,3 92 38-102 23