Built-in Wine Cooler Santo W 9 88 20 - 4i USER INSTRUCTIONS
Contents Safety Instructions / Standards 3 Disposal of packaging and old appliances 4 Installation / Installation site Your cooler needs air Installation Electrical connection 5 6 6 7 Product description 8 Interior fittings 8 User panel 8 Commissioning – setting temperature, switching off 8 Adjusting storage racks 9 Adjusting the temperature zone divider 10 Changing the light fitting 10 Proper loading 11 Ideal drinking temperatures 11 Defrosting 11 Cleaning 11 Energy-saving tips
Dear Customer Please read these instructions carefully before starting to use your wine cooler. They contain important information about the safe operation, installation and maintenance of your appliance. Please keep them for reference and pass them on to any subsequent user. Safety Instructions This refrigerator conforms to recognised technical regulations and to the EC guideline /EEC (low voltage guideline).
Disposal Information about the appliance packaging Dispose of your appliance packaging properly. None of the packaging materials used are harmful to the environment and they may be re-used. About the materials: the plastics may also be recycled and are identified as follows: >PE< for polyethylene e.g. in the outer casing and internal pockets. >PS< for polystyrene foam, e.g. in padding. Essentially CFC-free. The cardboard used is made from recycled paper and should also be put out for old paper collection.
Installation Installation site The appliance should be positioned in a well-ventilated, dry room. The ambient temperature will influence energy consumption and the proper functioning of the unit. For this reason, the appliance . Should not stand in direct sunlight; . Should not stand near a radiator, a stove or any other heat source; . Should be located only where the ambient temperature is compatible with the climatic classification of the appliance.
The cooler needs air The cooler door seals the installation unit almost completely, so an air vent is provided in the base of the housing. Warmed air must be conducted via the ventilation shaft to the rear wall of the housing and then expelled upwards. The ventilation channels should measure at least 200 cm2 in cross-section. min. 200 cm 2 50 min. 200 cm2 Warning! To ensure the proper functioning of the appliance, air vents should never be blocked or covered.
After installing the unit, and particularly if the door hinge is reversed, please ensure that the door seal is tight all round. An imperfect door seal can lead to increased condensation and thus to higher energy consumption (see the section headed “Troubleshooting”). Electrical connection A properly installed socket outlet with earthing contact is required for electrical connection, positioned so that it is possible to pull out the mains plug.
Product description 1 2 3 2 1 2 3 Control panel Storage racks (adjustable) Temperature zone divider (adjustable) Control panel 1 4 2 3 2a 1 Appliance on/off Press for at least 3 seconds. 2 Select upper zone temperature (5 to 18° C, adjustable) Recommendation: 5–12° C (ideal for white wine, see page 11) Press for at least 3 seconds indicator flashes The temperature can be adjusted in steps.
3 Supercool Press for 3 seconds the yellow pilot light illuminates. The appliance cools the upper zone for 24 hours at +5° C and then automatically at the set temperature. 4 Interior light switched on permanently: Press for 3 seconds ON Interior light on only while the door is open: Press for 3 seconds OFF If the door is kept open for longer than 5 minutes, an acoustic door alarm will sound. This can be switched off by briefly pressing any button.
To adjust the temperature zone divider The temperature zone divider can be raised or lowered by 1 position. Pull forwards away from the rear wall, and lift on door side. Reverse this procedure to replace at a different level. Please ensure that the rear section of the temperature zone divider slots into the groove provided in the rear wall. To change LED lighting Click off the LED light cover. Loosen the plug of the LED light fitting. Reverse this procedure to insert a new LED light fitting.
Proper loading The appliance is separated into 2 adjustable temperature zones (both adjustable from 5 to 18° C): Top compartment Bottom compartment white wine, champagne, sparkling wine, rosé wine. red wine Please ensure that the temperature set for the bottom compartment is always at least the same as or higher than that in the top compartment.
Never steam-clean the appliance. Dampness may penetrate the electrical components, creating the risk of an electric shock. Hot steam may damage the plastic components. The appliance must be dry before it is used again. Caution! Plastic components may be attacked by essential oils and organic solvents such as fruit juices and the acids in butter, as well as by detergents containing vinegar. Such substances should not come into contact with appliance components. Do not use abrasive cleaning agents.
Fault Possible cause Appliance doesn’t work. Appliance is not switched Switch on. on. Inadequate cooling chamber temperature. Solution Mains plug is loose or not plugged in. Insert the mains plug. Fuse has triggered or is defective. Check fuse and replace if necessary. Socket is defective. Faults with the mains supply must be repaired by a qualified electrician. Temperature has not been properly set. Please see under “Commissioning”. Door was open for a long period.
Guarantee The guarantee runs from the date on which the appliance is delivered to the end user. Under the terms of the guarantee, the customer service department will rectify any faults which may occur despite proper use during the guarantee period and which may be attributable to faulty materials or manufacture. Excluded from the guarantee are: . Defects arising from improper use or failing to observe the operating instructions. . Claims for damages which exceed the terms of our guarantee. .
Description Cause Comment Droning Cooling aggregate Normal operating noise of the cooling aggregate. The level is dependent on the size of cooler. Humming Fan Normal operating noise of the fan. Gurgling Babbling Murmuring Cooling circuit Normal operating noise as coolant flows through the circuit. Hissing Cooling circuit Normal operating noise as coolant is injected into the condenser. Cracking Cooler housing Normal as materials expand and contract due to temperature variations (e.g.
8 058
