SANTO Z 7 19 90-5 i Benutzerinformation User Manual Kühl-Gefriergerät Fridge-Freezer
Dear Customer Thank you for choosing one of our high-quality products. With this appliance you will experience the perfect combination of functional design and cutting edge technology. Convince yourself that our appliances are engineered to deliver the best performance and control - indeed we are setting the highest standards of excellence. In addition to this you find environmental and energy saving aspects as an integral part of our products.
Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Remove transport safeguard . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety The safety aspects of our refrigerators/freezers comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, we consider it our obligation to make you aware of the following safety information: Intended use • The refrigerator is intended for use in the home. It is suitable for the cooling, freezing and storing of frozen food, as well as for making ice.
the fridge when playing (there is risk of suffocation!)or get themselves into other dangerous situations. • Often children cannot recognise the hazards present in household appliances. It is therefore important that you ensure adequate supervision and never let children play with the appliance! Daily Operation • Containers with flammable gases or liquids can leak at low temperatures.
Disposal Appliance Packaging Information All materials are environmentally sound! They can be dumped or burned at an incinerating plant without danger! About the materials: The plastics can be recycled and are identified as follows: >PE< for polyethylene, e.g. the outer covering and the bags in the interior. >PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluorocarbon.
Installation Installation Location The appliance should be set up in a well ventilated, dry room. Energy use is affected by the ambient temperature. The appliance should therefore – not be exposed to direct sunlight; – not be installed next to radiators, cookers or other sources of heat; – only be installed at a location whose ambient temperature corresponds to the climate classification, for which the appliance is designed.
Building the appliance in • Fit the appliance into the recess. • Rotate the bracket of 180° in order to obtain the right position ( 2). The position (1) is on the delivery. • Fix it to a solid wall with the appropriate bracket.
Positioning Height adjustment The height of the appliance is adjustable from 820 to 870 mm to fine up with existing kitchen units. 820 870 Before installing the appliance between unite, adjust the height of the feet and rear wheels. The wheels are factory set for a height of 820 mm. To align the appliance to a height of 870 mm, raise it by adjusting the feet with a spanner, then remove the wheels and refit them in the lowest position.
Fitting the side panels • Fit the brackets onto the panels in the positions shown in the diagram. The dimension of 260 * mm is allowed for fitting a 100 mm plinth below the panel. For different plinth sizes, increase the dimension of 260 * mm accordingly. REAR EDGE FRONT EDGE RIGHT HAND SIDE PANEL 15 820 27,5 INSIDE FACE 15 280 997 82,2 520,8 3 541 7,5 260* • Rest the panels against the appliance.
Fitting the door panels 85 300 85 24 BOTTOM LEFT-HAND FRONT PANEL BOTTOM RIGHT-HAND FRONT PANEL 305 12 22 22 12 5 3 MIN 1062 TOP LEFT-HAND FRONT PANEL 1051 1051 TOP RIGHT-HAND FRONT PANEL 1062 • Before installing the doors, carefully level the appliance. 300 24 • Perforate the doors as in the drawing and insert the two screws in the bag (do not tighten them all the way down) for doors. 80 80 305 444 MIN. 447 MAX.
• Shut the door again and check that it is positioned at the requested height. If necessary, use the adjustment screws situated above the plate and the hinge. • Use the same adjustment screws to align the doors vertically. • Check horizontal alignment of the doors and, if necessary, correct their position by moving them along the slots. • Open the door. Adjust the planarity of the doors by means of the adjustment bushings and the lower square.
• Once the doors are perfectly and completely aligned, fix a clamp screw inside the bushings (upper and lower hinge) on the lower bracket. The screws must be tighten completely inside the slots. Building the appliance in • Fit the appliance into the recess. 1 • Rotate the bracket of 180° in order to obtain the right position ( 2). The position (1) is on the delivery. 2 • Fix it to the wali with the appropriate bracket.
Fitting the plinth Alignment height of 820 mm • If using a 140 to 170 mm plinth, make a cut-out as shown. 820 870 170 220 90 0 140 30 190 100 • • If using a plinth higher than 100 mm but less than 140 mm, cut the height compensation strip supplied with the appliance to the required depth and fit it between the plinth and the ventilation griile, pressing it into position below this grille. 140 190 If using a 100 mm plinth, fit the complete height compensation strip.
Alignment height of 870 mm • If using a 190 to 220 mm plinth, make a shown. • If using a plinth higher than 150 mm but less than 190 mm, cut the height compensation strip supplied with the appliance to the required depth and fit it between the plinth and the ventilation grille. 30 100 • If using a 150 mm plinth, fit the complete height compensation strip. • If the appliance is installed at the end of a row of units, insert foot E to hold the plinth in place.
Electrical connection Before initial start-up, refer to the appliance rating plate to ascertain if supply voltage and current values correspond with those of the mains at the installation location. e.g.: AC 220 ... 240 V 50 Hz or 220 ... 240 V~ 50 Hz (i.e. 220 to 240 volts alternating current, 50 Hertz) The rating plate is inside the appliance on the left. A correctly installed, earthed socket is required for the electrical supply. The supply must have a fuse rating of at least 10 Amps.
Operating and indicator panel Freezer A B C D E FGHI A. B. C. D. E. F. G. H. I. Mains pilot indicator (green) Freezer button ON/OFF Temperature setting button (for warmer temperatures) Temperature display Temperature setting button (for colder temperatures) Alarm reset light Alarm reset button FROSTMATIC function "on" indicator (yellow) FROSTMATIC button Temperature setting buttons • • The temperature is adjusted using the „C“ and „E“ buttons. These buttons are connected to the temperature display.
ACTUAL temperature means: The temperature display indicates the current temperature inside the freezer. The ACTUAL temperature is indicated with illuminated numbers. Temperature display The temperature display can indicate several pieces of information. • During normal operation, the temperature currently present in the freezer (ACTUAL temperature) is displayed. • When the temperature is being adjusted a flashing display indicates the freezer temperature currently set (DESIRED temperature).
2. If the FROSTMATIC function is not ended manually, the appliance switch off the FROSTMATIC function after 48 hours. The yellow light goes out. The FROSTMATIC function can be ended manually at any time by pressing the FROSTMATIC button again. The yellow light goes out. Alarm reset button In the event of an abnormal temperature rise inside the freezer (e.g. power cut) warning light (F) will start to flash and a buzzer will sound.
Freezing and storing frozen food You can use your freezer for freezing fresh food yourself. Important! 1. 2. • The temperature in the freezer compartment must be –18 °C or colder before freezing food. • Please observe the freezing capacity given on the rating plate. The freezing capacity is the maximum quantity of fresh food that can be frozen within a period of 24 hours. If you wish to freeze food several days in a row, please observe a maximum capacity of only 2/3 to 3/4 of that on the rating plate.
Preparation of Ice Cubes 1. 2. Fill the ice cube tray 3/4 full with cold water, place it in the freezer compartment and leave to freeze. To loosen the frozen cubes, either bend the ice cube tray or hold it under running water for a few seconds. Important! Never try to free an ice tray that is frozen to the freezer compartment using pointed or sharp edged objects. Use the ice scraper supplied.
Operating and indicator panel Fridge J K L M N OP J. K. L. M. N. O. P. Mains pilot indicator (green) Fridge button ON/OFF Temperature setting button (for warmer temperatures) Temperature display Temperature setting button (for colder temperatures) COOLMATIC function "on" indicator (yellow) COOLTMATIC button Temperature setting buttons • • The temperature is adjusted using the „L“ (+) and „N“ (-) buttons. These buttons are connected to the temperature display.
• • During normal operation, the temperature currently present in the fridge (ACTUAL temperature) is displayed. When the temperature is being adjusted a flashing display indicates the fridge temperature currently set (DESIRED temperature). Starting Up - Setting the Temperature 1. 2. 3. 4. 5. Plug the mains plug into the mains socket. Press ON/OFF button. The green mains pilot indicator illuminates. The appliances start. Press either the „L“ (+) or „N“ (-) button.
Refrigerator compartment For proper opening and closing, it is advisable to act on both doors simultaneously (as shown in the figure). • Do not place hot food or drinks in the refrigerator; wait until they trave cooled to room temperature. • Always cover foods, especially those which are strong-smelling or aromatic. • Place foods so that air can circuiate freely round them.
Superchill compartment • The temperature in this compartment (from 0°C to +3°C) is kept constant by a special sensor. No adjustment is needed. • Products stored in this compartment will keep fresh and in peak condition. It is advisable to wrap foods in aluminium foil or plastic film. • Drinks can be cooled quickly in this compartment without any danger of freezing • Make sure that the drawers are fully closed before shutting the door.
Defrosting Refrigerator Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates.
1. 2. 3. 4. 5. Do not allow such substances to come into contact with appliance parts. • Do not use any abrasive cleansers. Remove frozen food and the food from the refrigerator. Wrap frozen food in several layers of newspaper. Store it in a cool place, well covered. Defrost the freezer compartment prior to cleaning (see "Defrosting" section). Switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker or fuse.
What to do if ... Correcting Malfunctions A malfunction may be caused by only a minor fault that you can rectify yourself using the following instructions. Do not perform any other work on the appliance if the following information does not provide assistance in your specific case. Warning! Repairs to refrigerators/freezers may only be performed by qualified service engineers. Improper repairs can give rise to significant hazards for the user.
Malfunction Possible Cause Remedy Temperature is not properly adjusted. Please look in the "Initial Start Up" section. Door was open for an extended period. Open the door only as long as necessary.. Press the fast freeze switch A large quantity of warm The freezer temperature is not food was placed in the sufficient, red light lights up, appliance within the last 24 temperature signal sounds hours. The appliance is near a heat source.
Changing the light bulb 1. 2. 3. 4. 5. 6. Warning! There is a risk of electric shocks! Before changing the light bulb, switch off the appliance and unplug it, or pull the fuse or the circuit breaker. Light bulb data: Replace the lamp with one of the same power (the maximum power is shown on the light diffuser). To switch off the appliance, press the ON/OFF buttons (B-K). Unplug the mains plug. Remove the cover. Use bulbs of 15 W max. Change the defective light bulb. Refit the light bulb cover.
Subject to change without notice www.electrolux.com Änderungen vorbehalten www.aeg-electrolux.be www.aeg.
