LAVATHERM 548 CARAT Kondensationstrockner Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Umwelttipps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Gerätebeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bedienblende . . . . . . . . . . . .
Aufstell- und Anschlussanweisung . . . . . . . . . . . . . . . . . . . . . . . 23 Sicherheitshinweise für die Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Transportsicherung entfernen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Elektrischer Anschluss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Türanschlag wechseln . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“ • Vor Inbetriebnahme das Gerät auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten. Bestimmungsgemäße Verwendung • Der Trockner ist nur zum Trocknen haushaltsüblicher Wäsche im Haushalt bestimmt. • Umbauten oder Veränderungen am Trockner sind nicht zulässig.
Sicherheit von Kindern • Verpackungsteile von Kindern fernhalten. Erstickungsgefahr! • Kinder können Gefahren, die im Umgang mit Elektrogeräten liegen, oft nicht erkennen. Lassen Sie Kinder nicht unbeaufsichtigt beim Trockner. • Stellen Sie sicher, dass Kinder oder Kleintiere nicht in die Trommel des Trockners klettern. Lebensgefahr! Halten Sie die Tür des Trockners geschlossen, wenn er nicht benutzt wird. Allgemeine Sicherheit • Reparaturen am Trockner dürfen nur von Fachkräften durchgeführt werden.
2 1 Altgerät Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall zu behandeln ist, sondern an einem Sammelpunkt für das Recycling von elektrischen und elektronischen Geräten abgegeben werden muss. Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Umwelt und Gesundheit werden durch falsches Entsorgen gefährdet.
Gerätebeschreibung Schublade mit Kondensatbehälter Bedienblende Feinsieb (Flusensieb) Microfeinfilter (Flusensieb) Grobsieb (Flusensieb) Typschild Einfülltür (Anschlag wechselbar) Sockeltür vor Wärmetauscher Luftschlitze Schraubfüße (höhenverstellbar) Bedienblende Programmablauf-Anzeige Tasten- und Anzeigenblock 8 Programmwähler Wartungs-Anzeigen – WÄRMETAUSCHER (reinigen!) – BEHÄLTER (leeren!) – SIEB (Flusensiebe reinigen!)
Vor dem ersten Trocknen Um eventuelle fertigungsbedingte Rückstände zu entfernen, Trommel des Trockners mit einem feuchten Tuch auswischen oder kurzen Trockengang (20 MIN) mit feuchten Tüchern durchführen. Wäsche sortieren und vorbereiten Wäsche sortieren • Nach Gewebeart sortieren: – Baumwolle/Leinen für Programme der Programmgruppe BAUMWOLLE. – Mischgewebe und Synthetics für Programme der Programmgruppe MISCHGEWEBE. • Nach Pflegekennzeichen sortieren.
SCHON SIGNAL EXTRATROCKEN 5kg • • Durchtrocknen von dicken oder mehrlagigen Textilien, z. B. Frotteewäsche, Bademäntel. mn STARKTROCKEN 5kg • • Durchtrocknen von dicken Textilien, z. B. Frotteewäsche, Frotteehandtücher. mn SCHRANKTROCKEN 5kg • • Durchtrocknen von Textilien gleichmäßiger Dicke, z. B. Frotteewäsche, Trikotwäsche, Frotteehandtücher. mn LEICHTTROCKEN 5kg • • Für dünne Textilien, die noch gebügelt werden, z. B. Trikotwäsche, Baumwollhemden.
WOLLPFLEGE AUFFRISCHEN 1kg 1kg 1kg SIGNAL LEICHTBÜGELN 1kg SCHON 20 MIN 40 MIN max. Füllmenge (Trockengewicht) Programme Zusatzfunktionen Anwendung/Eigenschaften Pflegesymbole • • Zum Nachtrocknen von einzelnen Wäschestücken oder für kleine Mengen unter 1kg. m l1) n m l2) n • Spezialprogramm mit Anti-Knittermechanik für pflegeleichte Textilien wie Oberhemden und Blusen; für minimalen Bügelaufwand. Ergebnis ist abhängig von Textilart und Textilveredelung. (Die Füllmenge entspricht ca.
Trocknen Gerät einschalten Den Programmwähler auf ein beliebiges Programm drehen. Das Gerät ist eingeschaltet. Einfülltür öffnen/Wäsche einfüllen 1. Einfülltür öffnen: Dazu kräftig gegen die Einfülltür drücken (Druckpunkt 2. Wäsche locker einfüllen. 1 ) Achtung! Keine Wäsche zwischen Einfülltür und Gummidichtung einklemmen. 3. Einfülltür fest zudrücken. Schloss muss hörbar einrasten. Programm wählen Gewünschtes Programm mit Programmwähler einstellen.
SCHON Für besonders schonendes Trocknen empfindlicher Gewebe mit dem Pflegekennzeichen l sowie für temperaturempfindliche Textilien (z. B. Acryl, Viskose). Programm wird mit verminderter Heizleistung ausgeführt. SCHON ist nur bei Füllmengen bis 2,5kg sinnvoll! SIGNAL Nach Ende des Trockengangs ertönt in Abständen ein akustisches Signal. Programm starten Taste START/PAUSE drücken. Das Programm wird gestartet. Die Programmablaufanzeige zeigt den Fortgang der Trocknung an.
Trockengang beendet/Wäsche entnehmen 3 14 Nachdem der Trockengang beendet ist, leuchten die Anzeigen ENDE und KNITTERSCHUTZ. Wurde die Taste SIGNAL gedrückt, ertönt in Abständen ein akustisches Signal. An den Trockengang schließt automatisch eine ca. 30-minütige Knitterschutzphase an. Dabei dreht sich die Trommel in Intervallen. So bleibt die Wäsche locker und knitterfrei. Während der Knitterschutzphase kann die Wäsche jederzeit entnommen werden.
Reinigung und Wartung Flusensiebe reinigen 1 Um einen einwandfreien Betrieb des Trockners zu gewährleisten, müssen die Flusensiebe (Microfeinfilter und Feinsieb) nach jedem Trockengang gereinigt werden. Achtung! Den Trockner nie ohne Flusensiebe oder mit beschädigten oder verstopften Flusensieben betreiben. 1. Einfülltür öffnen 2. Den Microfeinfilter, der im unteren Bereich der Einfüllöffnung eingelassen ist, mit angefeuchteter Hand reinigen. 3. Entriegelungstaste am Grobsieb nach unten drücken.
3 Gesamten Siebbereich reinigen Der Siebbereich braucht nicht nach jedem Trockengang gereinigt zu werden, sollte aber regelmäßig kontrolliert und gegebenenfalls von Flusen gereinigt werden. 6. Dazu Grobsieb oben anfassen und nach vorn ziehen, bis es sich aus den beiden Halterungen löst. 7. Flusen aus dem gesamten Siebbereich entfernen – am besten mit dem Staubsauger. 8. Beide Zapfen des Grobsiebes in die Halterungen an der Einfülltür drücken, bis sie einrasten. 9. Das Feinsieb wieder einsetzen. 10.
1. Schublade mit Kondensatbehälter ganz herausnehmen (1) und den Auslaufstutzen des Kondensatbehälters bis zum Anschlag hochziehen (2). 3 2. Kondensat in ein Becken oder dergleichen ausgießen. 3. Auslaufstutzen einschieben und Kondensatbehälter wieder einsetzen. Falls das Programm wegen vollem Kondensatbehälter unterbrochen wurde: Taste START/PAUSE drücken, um den Trockengang fortzusetzen. Der Kondensatbehälter fasst ca.
4. Beide Sicherungsscheiben nach innen drehen. 5. Wärmetauscher am Griff aus dem Sockel herausziehen und waagrecht transportieren, um zu vermeiden, dass Restwasser ausläuft. 6. Zum Entleeren den Wärmetauscher senkrecht über ein Spülbecken halten. 1 3 Achtung! Zur Reinigung keine spitzen Gegenstände verwenden. Der Wärmetauscher könnte undicht werden. 7. Wärmetauscher reinigen. Am besten eine Handbürste verwenden oder mit einer Handbrause kräftig durchspülen. 8.
Bedienblende und Gehäuse reinigen 1 Achtung! Keine Möbelpflegemittel oder aggressive Reinigungsmittel zur Reinigung des Gerätes benutzen. Bedienblende und Gehäuse mit einem feuchten Tuch abwischen. Was tun, wenn... Kleine Störungen selbst beheben Falls der Trockner während des Betriebs eine Fehlermeldung anzeigt (eine oder mehrere Anzeigen auf der Programmablauf-Anzeige blinken), prüfen Sie bitte zunächst, ob Sie das Problem mit Hilfe nachstehender Tabelle selbst beheben können.
Problem Mögliche Ursache Abhilfe Beim nächsten Trocknen anderes Falsches Programm gewählt. Programm wählen (siehe Kapitel „Programmübersicht“). Trockenergebnis nicht zufriedenstellend. Flusensiebe verstopft. Flusensiebe reinigen. Wärmetauscher verflust. Wärmetauscher reinigen. Falsche Füllmenge. Empfohlene Füllmenge beachten. Lüftungsschlitze im Sockelbereich verdeckt. Lüftungsschlitze im Sockelbereich freimachen. Belag an Trommelinnenfläche oder an Trommelrippen.
Programmiermöglichkeiten Ziel Durchführung Akustisches Signal, das an das Programmende erinnert, fest einprogrammieren. 1. Programmwähler auf beliebiges Programm drehen. 2. Taste SIGNAL ca. 5 Sekunden gedrückt halten. Kurzes Signal ertönt mehrmals. Anzeige SIGNAL blinkt mehrmals. Damit ist die Einstellung fest einprogrammiert. Einstellung aufheben erfolgt wie unter 1. und 2. 1. Programmwähler auf beliebiges Programm drehen. 2. Die beiden Tasten SCHON und SIGNAL gleichzeitig ca.
Technische Daten 5 Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.1973 Niederspannungs-Richtlinie – 89/336/EWG vom 03.05.1989 EMV-Richtlinie einschließlich Änderungs-Richtlinie 92/31/EWG – 93/68/EWG vom 22.07.1993 CE-Kennzeichnungs-Richtlinie Höhe x Breite x Tiefe 85 x 60 x 60 cm Tiefe bei geöffneter Einfülltür 109 cm Höhenverstellbarkeit 1,5 cm Leergewicht ca. 40kg Füllmenge (programmabhängig) 1) max. 5kg Energieverbrauch nach IEC 1121 s. e.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Vor Inbetriebnahme müssen alle Teile der Transportsicherung entfernt sein. Andernfalls kann das Gerät beschädigt werden. • Vergewissern Sie sich vor Inbetriebnahme, dass die auf dem Typschild des Geräts angegebene Nennspannung und Stromart mit Netzspannung und Stromart am Aufstellort übereinstimmen. Die erforderliche elektrische Absicherung ist ebenfalls dem Typschild zu entnehmen.
3. Folienschlauch mit dem Polystyrolpolster aus dem Gerät ziehen. Elektrischer Anschluss Angaben über Netzspannung, Stromart und die erforderliche Absicherung sind dem Typschild zu entnehmen. Das Typschild ist im Bereich der Einfüllöffnung angebracht (siehe Kapitel „Gerätebeschreibung“). Türanschlag wechseln 1 Warnung! Der Wechsel des Türanschlags darf nur von einem Fachmann ausgeführt werden. Wenden Sie sich bei Bedarf an unseren Kundendienst oder an Ihren Fachhändler.
5. Scharniere A von Einfülltür abschrauben, um 180° drehen, auf gegenüberliegender Seite wieder einsetzen und festschrauben. 6. Abdeckplatten B und C um 180° gedreht auf der jeweils gegenüberliegenden Seite wieder einsetzen. 7. Abdeckplatten E von der Gerätevorderwand abschrauben, um 180° drehen und auf der gegenüberliegenden Seite anschrauben. 8. Türverriegelung F losschrauben, etwas nach unten drücken und aus der Gerätevorderwand herausnehmen. 9.
Sonderzubehör Über den Ersatzteil-Service (Tel.-Nr. 0180 322 66 22) oder Ihren Fachhändler ist folgendes Sonderzubehör erhältlich: Zwischenbausätze Wasch-/Trockensäule Mit diesen Zwischenbausätzen kann der Trockner zusammen mit einem AEG-Electrolux-Waschautomaten (60cm breit, Frontbeladung) zu einer platzsparenden Wasch-/Trockensäule angeordnet werden. Der Waschautomat steht unten, der Trockner oben. Zwei Ausführungen sind lieferbar: – ohne Ablageplatte 916.018 902 – mit ausziehbarer Ablageplatte 916.
Garantiebedingungen/Kundendienststellen Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
3. Mängel dieses Gerätes werden wir innerhalb angemessener Frist nach Mitteilung des Mangels unentgeltlich beseitigen. Die zu diesem Zweck erforderlichen Aufwendungen, insbesondere Transport-, Weg-, Arbeits- und Materialkosten werden von uns getragen. Ab dem siebten Monat der Garantiezeit übernehmen wir nur die Arbeits- und Materialkosten. Über diese Nachbesserung hinausgehende Ansprüche werden durch diese Garantie nicht eingeräumt.
Österreich Unsere Kundendienststellen und Servicepartner Electrolux stellt Ihnen hiermit jene Partner vor, die dafür garantieren, dass wir Ihnen Top-Qualität mit unseren Kundendiensteinrichtungen jetzt und in Zukunft bieten. Unsere Kundendienststellen in den Bundesländern sind spezialisiert auf unsere Marken: AEG, Electrolux, Juno, Zanussi. Zentrale: Kundendienst Wien, Niederösterreich, nördliches Burgenland Electrolux Hausgeräte GmbH 1230 Wien, Herziggasse 9 Tel. Reparaturannahme 01/86640-330 Tel.
Ersatzteile, Zubehör und Pflegemittel Für Oesterreich: Sie können Ersatzteile, Zubehör und Pflegemittel online bestellen bei http://www.aeg-hausgeraete.
Service Wenn Sie einmal unsere Hilfe benötigen, erreichen Sie uns in Deutschland wie folgt: Bei Fragen zu Bedienung oder Einsatz Ihres Gerätes Wenden Sie sich an den AEG-Direct Info Service: Telefon: 0180 555 4 555 (0,12 Euro/Min)** Internet: www.aeg-hausgeraete.de Bei technischen Störungen Prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.