Introduction The hood is supplied as an extractor unit and ¢an also be used with a filtering function by fitting activated carbon fighters (special accessory. The unit features two outlet holes. one of which Dislocated on the top af the unit while the other B is located on the rear To connect up the hose, you should first fit my bayonet-mounting flange G (100 or 120 mm) on the outlet required (f using the top outlet, fix the flange in place using the screw supplied as shown in Fig.
Filter version | The airs filtered and recirculated through the front grille. Move the lever F to position F Fig. 3. Willie need an original AEG KLF60/80 activated carbon filter for my littering function. (See special accessories).
Electrical connections Check hat the power supply voltage shown on the raking plate corresponds to the mains supply before proceeding 1o make any electrical connections. {l the unit is supplied ready-fitted with a plug, it can be connected to any easily accessible socket installed in compliance with the regulations in force. It a fixed connection is required, the hood must be installed exclusively by an electrician registered with the local electrical company.
18 Specifications Dimensions: Height Width Depth {in mm) 152 598 505 Weight: Net: 87Kg Gross: 96Kg Maximum absorbed power: 230 W Motor absorption: 1 x150W Lighting: 2x40W Fan powers (levels), levels in compliance with DIN 44171 Level: 1 2 3 intensive Extractor: 115mYh 142 m¥%h 194 m¥h 283 mYh Version: €8 m%h 119 m¥h 161 mh 18t mih Extractor system: 100 and 120 mm @
Installation When used as an extractor unit, the hood must be fitted with a 100 or 120 mm diameter hose. i the outlet hose is installed in a horizontal position, i must nevertheless be slanted at an angle of 10° so that the air can flow outside without impediment. When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hobnobbing surfaces:! electric cookers 650 mm gas cookers 850 mm coal and oil cookers 700 mm min.
Walt unit mounting 20 Since the rule for rooms with fuel burning appliances is “gutting hole of the same size as the ventilation hole”, a hole of 500-600 cave, which is 10 say a larger hole, could reduce the performance of the extractor hood. 1f the hood is used in its filtering function, it will opera la simply and stately in the above conditions without the need for any of the aforementioned measures.
— Position the template on the wall. Wall — Dl four 8 sm @ files in the wall, 2 in points H and 2 in points 1. mounting — Fit the four 8 mm screw anchor plugs in the wall. — Resew two screws in points H but do not tighten them fully home. — Adjust the unit so that it is positioned at a fight ante o the wall by turning the fwo support screws G. Now hang the hood on the wall (holes H). Tighten the first two screws and, for safety’s sake, screw the other two s Craws into the holes in the hood. Fig.
Safety warnings for user 22 Hood Operation The hood is filed with a vanadium speed motor. The most defective usa of he hood is obtained by switching it on a lew minutes be lure you stein cooking and leaving it on a for approximately 18 minutes after you nave finished, thus ensuring all cooking odors are eliminated.
Maintenance and care The hood must always be disconnected from the mains power supply before beginning any maintenance work, Open my latch L and swing the grille downwards. ~— Fig. 7. -~ To remove the grille, pull it forwards from the right and release it. = My grease filter has been designed to absorb the grease particles that are formed during cooking and is always used, respective of whether the hood is set up for extractor or filter operation. The synthetic filter s very thin {approx.
Warning Changing the light bulb 24 Removing the filter Press the spats N and remove the filter by pulling it downwards. — Fig. Always specify the hood modal code number and serial number when ordering replacement litters. This information is shown on the registration plate located on the inside of the uni. The activated carbon fitter can be ordered from the AEG technical Assistance service. Failure! to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard.
Cleaning Warning always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects w the motor's protective grille, Wash my outside surfaces using a delicate detergent inhibition Never use cause detergents or abrasive brushes or powders Only ever clean the switch panel and filter rifle using a damp lath and delicate detergents. 1st extremely important to clean the unit and change the filters at the recommended intervals.
1t your appliance has a fault, please contact our service engineer and state the following numbers: FNr AEQ Exaggerate AG Posthaste 1036 D-80327 Kornberg 1 © Copyright by AEG H 260 264 700 L 407A Ed.