2460 D Cooker hood Operating and Installation Instructions
Printed on recycled paper AEG - putting words into action 2
Contents Safety warnings For the User For the Installer 4 4 4 Description of the Appliance Extractor version Filter Version 6 6 6 Control Panel 7 Maintenance and care Cleaning the hood Metal grease filter Removing the metal grease filter Charcoal filter Changing the light bulb 8 8 8 8 10 11 What to do if 12 Service and Spare Parts 13 Guarantee Conditions 14 Technical Specifications Mounting accessories included 16 16 Electrical connection Safety warnings for the electrician Wall unit mountin
Safety warnings For the User • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. • Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control. • The hot oil in the frying pan might ignite due to overheating.
• It is advisable to apply for authorization from the relevant controlling authority when connecting the outlet to an unused chimney flue or combustion gas duct. The air outlet installation must comply with the regulations laid down by the relevant authorities. • When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole.
Description of the Appliance • The hood is supplied as an extractor unit and can also be used with a filtering function by fitting one charcoal filter • You will need an original AEG charcoal filter for this function (Available from your local AEG Service Force Centre). Extractor version • The air is discharged to the outside through a hose, which must be fitted to connection flange A. Fig. 1. • In order to obtain the best performance the hose should have a diameter equal A to the outlet hole.
Control Panel • Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared.
Maintenance and care • The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood • Clean the outside of the hood using a damp cloth and a mild detergent. • Never use corrosive, abrasive or flammable cleaning products. • Never insert pointed objects in the motor’s protective grid. • Only ever clean the switch panel and filter grille using a damp cloth and mild detergents.
Dishwasher Place grease filters in dishwasher. Select the most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance.
Charcoal filter • The charcoal filter should only be used if you want to use the hood in its filtering function. • To do this you will need an original AEG charcoal filter. • Replacing the charcoal filter The charcoal filters cannot be cleaned, we recommend that they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. • Fitting Remove the frame b which supports the filter c by unscrewing it from the hood a, Fig. 4.
Warning • Failure to observe the instructions on cleaning the unit and changing the filters could cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulb • • • • • Disconnect the cooker hood from the mains supply.
What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively.. . Check that: The fan speed is set high enough for the task. The grease filters are clean. The kitchen is adequately vented to allow the entry of fresh air.
Service and spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk Please ensure that you have read the section „What to do if....
Guarantee conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances.
Technical Specifications Models Dimensions - extractor version (in cm): Height Width Depth 2460 D 68-113 59,8 45 Dimensions - filter version (in cm): Height 67,5-122,5 Width 59,8 Depth 45 Maximum absorbed power: 195 W Motor absorption: Lighting: 1 x 155 W 2 x 20W Length of the cable: 150 cm Mounting accessories included 6 wall plugs Ø 8 mm 6 wood-screws 5 x 45 mm 6 metal screws 2,9 x 6,5 8 metal screws 3 x 10 1 deflector 1 chimney support 1 reduction flange Ø 125-120 mm 1 support bracket 16
Electrical connection Safety warnings for the electrician The electric outlet should be placed inside the chimney.The hood has a power cable, 150 cm, with earth connection and the rated voltage is 220 - 240 V. Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts. This switch must be accessible at all times.
Wall unit mounting - Fig. 6 • Only for extractor version: position the upper section of the chimney so that the oulet slots H are not visible (see also A-B-C sequence on on Fig. 6). • Fix each other both parts of the hood (1), make all connections between the two parts (2) and fix with 6 screws (3).
A-B-C, Extractor version only! 20a 4 20a H G 14 14 20b 15 20b F 7-16 1 7-16 11 21 11 18 19 6 1 1 B 98 5 9 8 9 8 13 12 12 10 2 10 13 17 1 1 3 3 17 3 22 22 NOTE: 18 not supplied 3 Fig.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de © Copyright by AEG LI1UGB Ed.