User manual

ManualsBrandsAEG ManualsOther24658G-M

USE, INSTALLATION AND

MAINTENANCE INSTRUCTIONS

FOR BUILT-IN HOT PLATES

The manufacturer is not responsible for any transcription errors or misprints contained in this handbook and,

furthermore, reserves the right to make any modification on the products, which might be deemed necessary

or useful, this being also in the user’s interest, without altering their basic operating or safety features.

COD. 115800AEG680 - 03.10.2003

Dear User,

We are sincerely grateful to you for purchasing one of our products. This

appliance has been designed to meet all the modern requirements and is

manufactured from the finest materials and components.

We would ask you to read the instructions within this booklet very carefully so

as to enable you to obtain quality results from the outset.

The design of the figures contained in this handbook is purely indicative.

THE APPLIANCE MUST BE INSTALLED ONLY BY AUTHORISED

PERSONNEL IN COMPLIANCE WITH THE INSTRUCTIONS PROVIDED.

THE MANUFACTUTER DECLINES ALL RESPONSIBILITY FOR IMPROPER

INSTALLATION WHICH MAY HARM PERSONS AND ANIMALS AND

DAMAGE PROPERTY.

THE APPLIANCE MUST BE USED FOR THE PURPOSE FOR WHICH IT

WAS EXPRESSLY DESIGNED. ANY OTHER USE (e.g. HEATING ROOMS)

IS CONSIDERED TO BE IMPROPER AND CONSEQUENTLY DANGEROUS.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE

RESULTING FROM IMPROPER AND IRRESPONSIBLE USE.

Summary of content (12 pages)

PAGE 1
USE, INSTALLATION AND MAINTENANCE INSTRUCTIONS FOR BUILT-IN HOT PLATES Dear User, We are sincerely grateful to you for purchasing one of our products. This appliance has been designed to meet all the modern requirements and is manufactured from the finest materials and components. We would ask you to read the instructions within this booklet very carefully so as to enable you to obtain quality results from the outset. The design of the figures contained in this handbook is purely indicative.
PAGE 2
DESCRIPTION OF THE HOT PLATES 24658 G-m 24968 G-m 1) Large burner (Left front) 2) Medium burner (Right rear) 3) Small burner (Left rear) 4) Auxiliar burner (Right front) 5) Fish burner (Center) 6) Ultra rapid burner (Left front) 14) Right trivet 15) Center trivet 16) Left trivet 17) Trivet for ultra rapid burner 18) Eletric ignition push-button 19) Burner control knob n° 4 20) Burner control knob n° 1 21) Burner control knob n° 6 22) Burner control knob n° 5 23) Burner control knob n° 3 24) Burner control
PAGE 3
USE HOW TO USE THE BURNER HOTPLATES In order to maximize the efficiency of the burners the following pan sizes are recommended: 1) BURNERS Ensure that all gas supply connections are correct and that supply valves are open. The burner controls are engraved graphically to indicate their associated burner and setting. - MANUAL IGNITION (FIG. 1) Select desired hotplate burner, depress control knob and gently turn anti-clockwise to “Full on” position whilst applying a lighted match to the burner.
PAGE 4
USE - YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE. - DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS, LIQUIDS OR ITEMS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. WARNING - SAFETY: - BURNERS WITH FLAME FAILURE DEVICE MAY ONLY BE IGNITED WHEN THE RELATIVE KNOB HAS BEEN SET TO THE FULL ON POSITION (LARGE FLAME FIG.1). - NEVER ALLOW CHILDREN TO PLAY NEAR THE APPLIANCE WHEN USING THE BURNERS. CHECK THAT THE PAN HANDLES ARE POSITIONED CORRECTLY.
PAGE 5
CLEANING WARNING: Do not wash any part while it is still hot. 4) PARTS IN STAINLESS STEEL Parts in stainless steel must be cleaned with warm soapy water and dried with a clean soft cloth. Frequent use of cleaning agents designed for stainless steel is recommended. 2) HOTPLATE Periodically, the enamelled trivets, burners and burner caps should be washed with warm soapy water (fig. 5). Ensure they are completely dry and that all holes in the burners are clear of obstructions prior to reassembly.
PAGE 6
INSTALLATION THE CHILDREN SINCE THEY ARE A SOURCE OF POTENTIAL DANGER. TECHNICAL INFORMATION FOR INSTALLATION PERSONNEL 6) FIXING OF THE HOTPLATE WARNING: This appliance must be installed only by authorised personnel and in accordance with AS5601 (AG 601), the manufacturers installation instructions, relevant municipal building regulations, gas and electrical authority regulations. The wall and bench surfaces must be capable of sustaining temperatures of 75 degrees Celsius.
PAGE 7
INSTALLATION 7) GAS CONNECTION 8) ELECTRICAL CONNECTION The gas connection is located at the rear and on the underside of the appliance 100 mm from the right hand side. Natural Gas Natural Gas installations require the connection of a gas regulator at the appliance. Assemble the regulator (noting the gas flow direction) and transition pieces, in accordance with figure 12. THE APPLIANCE HAS BEEN FITTED WITH INJECTORS DESIGNED FOR NATURAL GAS. LPG (liquified petroleum gas) INJECTORS HAS BEEN SUPPLIED.
PAGE 8
REGULATION Warning: Adjustment of this appliance shall only be carried out only by authorised personnel. 10) CONTROL VALVES “Reduced rate” adjustment The control valves are suitable for all types of gases. They are the male cone type allowing one direction of flow. Simmer flame adjustment (refer figure 20) - Light burner and set to low setting. - Remove control knob (friction fit). - Insert a small screwdriver into the hollow stem of the valve and adjust the flame to the desired level.
PAGE 9
CONVERSIONS Warning: Conversion of this appliance shall only be carried out only by authorised personnel. figure 22). - Unscrew the injector with the open ended spanner until there is clearance for the spring hook “P”, to engage the injector. - Unscrew the injector completely. 11) REPLACEMENT OF INJECTORS The burners are suitable for use with different gases. To adjust to different gases it is necessary to change the injectors. A range of injectors are supplied with the appliance.
PAGE 10
MAINTENANCE Warning: Maintenance, service and repairs of this appliance shall only be carried out only by authorised personnel. and secure the screws (refer figure 25). Replacement of electric cable - Should the flexible supply lead need replacement it is essential that one of the correct rating and construction be used. The lead must contain an earth and this must be connected. Burner replacement (refer figure 26) - Disassemble the appliance as detailed above. - Remove screws "R" and plate "P".
PAGE 11
FIG. 29 FIG. 30 HOT PLATES TECHNICAL DATA PRESSURE 3 + 1 WOK BURNERS 3 + 1 WOK BURNERS “RECTANGULAR” “SOFT” 4 BURNERS (NO WOK) “RECTANGULAR” 24658 G-m PROPANE NATURAL 2.75 kPa 1.00 kPa 2.75 kPa 1.00 kPa 2.75 kPa 1.00 kPa TOT. HEAT INPUT 0.6 W 0.6 W 0.6 W PROPANE NATURAL 33.1 MJ/h 33.1 MJ/h 33.1 MJ/h 33.1 MJ/h 30.3 MJ/h 30.3 MJ/h VOLTAGE 240 V ~ 240 V ~ 240 V ~ FREQUENCY 50 Hz 50 Hz 50 Hz PRESSURE 4 + 1 WOK BURNERS 4 + 1 WOK BURNERS “RECTANGULAR” “RECTANGULAR” TOT.
PAGE 12
ANDI-CO AUSTRALIA PTY LTD ABN 68 005 899 365 For Service Phone: 1300 650 020 (in Australia) Spare Parts Tel: (03) 9569 7744 www.andico.com.