INSTRUCTION BOOK GB Wok burner 3531 WK-m 1 GB 949600835
Your New Appliance Thank you for purchasing an AEG appliance. To enable you to use your new appliance efficiently and safely, please read this instruction book carefully before installing or using the appliance, and retain for future reference. Should the appliance be transferred to a new owner please ensure this instruction book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings.
Table of contents Contents Page no For the user Your new appliance ...................................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 5 Placement of grid ................................................................................. 5 Operating instructions ................
Safety information These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. Child Safety Installing Maintenance and Cleaning This wok must be installed according to the instructions supplied. Any installation work must be undertaken by a qualified competent person.
Description of the product Burner Knob Placement of grid Guide pins for grid 5
Operating instructions The operating knob has a ring showing the scale of markings. Off. Max. flame and ignition position Min.
Burner cover/burner ring Together with the burner ring the burner cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Burner ring Burner cover Correct Please note: It is consequently very important that the burner cover/ring is placed correctly on the burner. The burner ring has been provided with holes for the ignition electrode, and the thermo sensor.
The wok-unit has a special pan support which enables use of a wok pot with curved bottom. When using cooking utensils with a flat bottom the diameter of the utensils must not be less than 26 cm.
Ignition 1. Depress and turn the control knob for the burner, the left to Max. flame 2. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. Is not possible to connect the unit to mains, a match may be used to ignite the burner 3. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo couple. 4.
Cleaning and maintenance For reasons of hygiene and safety, the cooking burner must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. The splashguard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashguard as shown in the diagram. 2. Lift the splashguard straight up 3. Clean the top surface as described in “cleaning the steel surface”. Be aware of the two retaining pegs, which are sharp. 4.
Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid cream. Always clean the steel in the direction of the steel finish. To ensure that the steel retains its shine, it is recommended that you use a polishing agent for stainless steel on a regular basis. Always polish in the direction of the steel finish (crosswise). Never use steel wool, metal sponges or other abrasive cleaning agents.
Technical data Type of gas Adjusted for Natural, G-20 - 20mbar 240 V 1N + PE N Category and pressures GB: II 20 - 28/37 mbar 2H3+ Max. nominal load Q, HS: Wok burner = 3,9 kW x 1 Total= 3,9 kW L1 The hob must be connected via an external switch with a contact gap of min. 3 mm (the main switch may be used) FSD The unit features fully-secured gas taps (thermo-fuse).
Important safety requirments This hob must be installed by qualified personnel to the relevant British Standards. This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Any gas installation must be carried out by a CORGI registered installer. Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions.
Gas connection Gas installation In accordance with local requirements for domestic gas cooking appliances. Gas installation must only be carried out by an authorised person. For gas types see technical data. Gas connection The gas intake is situated at the lower rear of the appliance. The intake has a ½" conical pipe thread (see fig 1) If the appliance is to be connected to a gas cylinder, conversion with the optional modification kit will be necessary.
Mounting MIN 55 Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. Headroom The distance to any shelves or tops of a cabinet under the hob is to be at least 55 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the table top.
It is not necessary to attach the reinforcement beam to the work top surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges.
Something not working If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. IMPORTANT: If you call out an engineer to a fault caused by incorrect use or installation, a charge will be made even if the hob is under guarantee. Sympton: Solution There is no spark when lighting the gas Check hob is connected to the electricity supply. Check the fuse and replace if necessery.
Service & spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will automatically be routed to the Service Centre covering your post code area. In-guarantee customers should ensure that the recommended checks under the heading "Something Not Working" have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.
Guarantee conditions AEG offer the following guarantee to the first purchaser of this appliance: 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty material.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local service organisation is aware of your move and able to look after you and your appliances.
325 88-1661 Rev.
