INSTRUCTION- AND INSTALLATION BOOK 6530 DG-m 1 SGP GB 949600247
Congratulations from AEG Dear Customer, Congratulations with your new Hob. It is important that you become familiar with the functions and features of the Hob. You should therefore read these operating instructions as they will help you get the most out of your new Hob. Pay extra attention to sections marked . These are warning texts to help you avoid accidents. Keep the operating instructions.
Table of contents Contents Page no For the user Your new aplliance ....................................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 6 Hofw to use ................................................................................................... 7 Burner ring/cover .......
Safety information Never use plastic or aluminium dishes on the gas hob. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. Never leave the gas hob unattended while deep fat frying, or heating fats and oils.
The primary air intake aperture Must never be accidentally blocked by objects of any kind.
Description of the product Air intake Burner Control knob 6
How to use Burner markings Symbols at each control knob indicates which burner is adjusted with the control knob. Front Burner Back burner Panel markings Each control knob has a ring showing the scale of markings. Off.
Together with the burner ring the burner ring/cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Please note: It is consequently very important that the individual burner cover/ring is placed correctly on the burner. If the burner ring/cover are wrongly placed the burner will operate incorrectly, and the burners may be damaged within at short space of time.
Ignition 1. Depress and turn the control knob for the burner to the left to max. flame . (Ignition position) 2. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. If it is not possible to connect the unit to mains, a match may be used to ignite the burner. 3. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo-couple (thermo sensor ready). 5.
Maintenance and cleaning For reasons of hygiene and safety, the cooking zones must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. The splashguard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashguard as shown in the diagram. 2. Lift the splashguard straight up 3. Clean the top surface as described in “cleaning the steel surface”. Be aware of the two retaining pegs, which are sharp. 4.
3. Wipe the ceramic hob clean with a damp cloth or kitchen towel. Tough stains can be removed by rubbing the stain hard with kitchen towel. 4. Wipe off remaining cleaning agent with a damp cloth. 5. Wipe with a dry cloth, if required. Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid cream. Always clean the steel in the direction of the steel finish.
Cleaning of gas burners Clean the control panel and knobs plus the pan grid, as well as burner caps and rings, with ordinary cleansing agents. Never use scouring powder, Brillo pads, metal pads or other scouring agents on enamelled or painted surfaces! Avoid boil-over If water accidentally gets into the edge of the burner head (boil-over) the water must be removed with a lint-free cloth before the burner is turned on again.
Mounting Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the table top. Tighten the brackets on to the table top with an ordinary screwdriver.
It is not necessary to attach the reinforcement beam to the table surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges. Installation in work tops with a base unit underneath If the hob is to be installed on top of a base unit, a board must be mounted underneath the hob (e.g. 16 mm chip board). Min. 140 mm Min. 16 mm Aluminium-tape Seal all joints with aluminium tape. The board can be mounted as shown in the diagram.
Do not install the hob above drawers.
The unit´s externally measured length 145 mm: Cooker hood 290 mm: Two-zone ceramic-top electric hob Two-burner gas hob Grill Fryer Wok 580 mm: Four-zone ceramic-top electric hob Four-burner gas hob 725 mm: Four-zone ceramic-top electric hob Installation of a single unit When mounting a single unit, be it a half-or full size unit, in a table surface which is thicker than 30 mm, it is necessary to make a special notch in both sides of the cut-out hole, as shown in the adjacent drawing.
Gas installation In accordance with local requirements for domestic gas cooking appliances. Gas installation must only be carried out by an authorised person. For gas types see technical data. Gas connection The gas intake is situated at the lower rear of the appliance. The intake has a ½" conical pipe thread (see fig 1) If the appliance is to be connected to a gas cylinder, conversion with the optional modification kit will be necessary. Pressure test The unit should be pressure-tested at Max. 150 mbar.
Technical data Type of gas Adjusted to bottled gas: G30-28/37 mbar Cable type 0,75 mm² HO5 V2V2-F 240 V 1N + PE Convertible to Towngas - G110 / 8 mbar N L1 Max. nominal load Q na HS: Medium sized burner = 1,9 kW x 1 Large sized burner = 2,7 kW x 1 Total= 4,6 kW The Dropinett must be connected via an external switch with a contact gap of min. 3 mm (the main switch may be used) FSD The unit features fully-secured gas taps (thermo-fuse).
Service If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Centre. IMPORTANT: If you call out an engineer to a fault caused by incorrect use or installation, a charge will be made even if the hob is under guarantee. Sympton: Solution There is no spark when lighting the gas Check hob is connected to the electricity supply. Check the fuse and replace if necessery.
325 88-1591 Rev.
