INSTRUCTION- AND INSTALLATION BOOK GB Gas hob 6531 DG-m 1 GB 949600278
Your New Appliance Thank you for purchasing an AEG appliance. To enable you to use your new appliance efficiently and safely, please read this instruction book carefully before installing or using the appliance, and retain for future reference. Should the appliance be transferred to a new owner please ensure this instruction book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings.
Table of contents Contents Page no For the user Your new appliance ...................................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 5 Operation instrutions .................................................................................. 6 Burner ring/cover ................
Safety information Never leave the hob unattended while deep fat frying, or heating fats and oils. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. The appliance is not intended for use by young children or infirm persons without supervision.
Description of the product Burner Control knob 5
Operations Burner markings Symbols at each control knob indicates which burner is adjusted with the control knob. Front Burner Back burner Panel markings Each control knob has a ring showing the scale of markings. Off.
Burner ring/cover Together with the burner ring the burner ring/cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Please note: It is consequently very important that the individual burner cover/ring is placed correctly on the burner. If the burner ring/cover are wrongly placed the burner will operate incorrectly, and the burners may be damaged within at short space of time.
Ignition 1. Depress and turn the control knob for the burner to the left to max. flame . (Ignition position) 2. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. If it is not possible to connect the unit to mains, a match may be used to ignite the burner. 3. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo-couple (thermo sensor ready). 5.
Maintenance and cleaning For reasons of hygiene and safety, the cooking zones must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. Splashguard The splashguard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashguard as shown in the diagram. 2. Lift the splashguard straight up 3. Clean the top surface as described in “cleaning the steel surface”. Be aware of the two retaining pegs, which are sharp. 4.
3. Wipe the ceramic hob clean with a damp cloth or kitchen towel. Tough stains can be removed by rubbing the stain hard with kitchen towel. 4. Wipe off remaining cleaning agent with a damp cloth. 5. Wipe with a dry cloth, if required. Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid cream. Always clean the steel in the direction of the steel finish.
Cleaning of gas burners Clean the control panel and knobs plus the pan grid, as well as burner caps and rings, with ordinary cleansing agents. Never use scouring powder, Brillo pads, metal pads or other scouring agents on enamelled or painted surfaces! Avoid boil-over If water accidentally gets into the edge of the burner head (boil-over) the water must be removed with a lint-free cloth before the burner is turned on again.
Technical data Type of gas Adjusted to natural gas: G20-20 mbar 240 V 1N + PE N Category and pressures UK: II 20 mbar - 28/37 mbar 2H3+ L1 Max. nominal load Q na HS: Medium sized burner = 1,9 kW x 1 Large sized burner = 3,0 kW x 1 Total= 4,9 kW The hob must be connected via an external switch with a contact gap of min. 3 mm (the main switch may be used) FSD The unit features fully-secured gas taps (thermo-fuse).
Important safety requirements This hob must be installed by qualified personnel to the relevant British Standards. This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Any gas installation must be carried out by a CORGI registered installer. Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions.
Connection to the gas supply should be with either rigid or semirigid pipe, i.e. steel or copper. The connection should be suitable for connection to RC ½ (½ BSP male conical thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installaion. Ensure that the main connection pipe does not exert any strain on the hob. It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connection pipe.
Mounting MIN 55 Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. Headroom The distance to any shelves or tops of a cabinet under the hob is to be at least 55 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the table top.
It is not necessary to attach the reinforcement beam to the table surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges.
The unit´s externally measured length 145 mm: Cooker hood 290 mm: Two-zone ceramic-top electric hob Two-burner gas hob Grill Fryer Wok 580 mm: Four-zone ceramic-top electric hob Four-burner gas hob 725 mm: Four-zone ceramic-top electric hob Installation of a single unit When mounting a single unit, be it a half-or full size unit, in a table surface which is thicker than 30 mm, it is necessary to make a special notch in both sides of the cut-out hole, as shown in the adjacent drawing.
Something not working If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. IMPORTANT: If you call out an engineer to a fault caused by incorrect use or installation, a charge will be made even if the hob is under guarantee. Sympton: Solution There is no spark when lighting the gas Check hob is connected to the electricity supply. Check the fuse and replace if necessery.
Service & spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will automatically be routed to the Service Centre covering your post code area. In-guarantee customers should ensure that the recommended checks under the heading "Something Not Working" have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.
Guarantee conditions 6. The purchaser's statutory rights are not affected by this guarantee. AEG offer the following guarantee to the first purchaser of this appliance: 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty material.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local service organisation is aware of your move and able to look after you and your appliances.
325 88-1621 Rev.
