MANUAL DE INSTRUCCIÓN E INSTALACIÓN 6560 G-m 1 ES 949600547
Felicidades de AEG Estimado cliente: Lo felicitamos por su nuevo Frontline. Es importante que se familiarice con las funciones y características del encimera . Por ello, debe leer detenidamente estas instrucciones de empleo ya que le ayudarán a sacar el mayor provecho de su nuevo encimera. Ponga mayor atención en las secciones marcadas . Estos son textos de advertencia para ayudarle a evitar accidentes. Guarde las instrucciones de empleo.
Índice Contenido Número de página Para el usuario Felicidades de AEG ..................................................................................... 2 Información de seguridad ........................................................................... 4 Descripción del producto ........................................................................... 6 Operaciones ................................................................................................. 7 Anillo/tapa de quemador ...........
Información de seguridad No utilice la placa de gas si está defectuosa. Diríjase al Centro de Servicios AEG local. No utilice nunca platos de plástico ni de aluminio en la placa de gas. Estas advertencias tienen como objetivo garantizar su seguridad. Procure que las haya entendido antes de instalar o utilizar el aparato. Su seguridad es de suma importancia. Si tiene dudas sobre el sentido de estas advertencias, diríjase al Departamento de Servicio al Cliente.
Entregue los posibles embalajes y aparatos usados a un vertedero de residuos autorizado. La abertura de la toma de aire primario No debe nunca taparse por descuido con objetos de ningún tipo.
Descripción del producto Toma de aire Quemador Botón de mando 6
Operaciones Señales de los quemadores Las señales en cada botón funcional indican que el quemador se regula mediante el correspondiente botón. Quemador delantero izquierdo Quemador trasero izquierdo Quemador trasero derecho Quemador delantero derecho Señales del panel Cada botón funcional tiene un anillo que indica la escala de las señales Off. Fuego máx. Fuego mín.
Anillo/tapa de quemador El anillo de quemador y la tapa del anillo de quemador forman un espacio donde tiene lugar la mezcla final del gas y del aire para obtener una combustión correcta del gas. Atención: Por ello, es muy importante que cada tapa/anillo de quemador se coloque correctamente sobre el quemador. Si el anillo/la tapa se coloca mal, el quemador no funcionará correctamente, lo cual en poco tiempo podrá causar daños en los quemadores.
Ignición * Pulsar el botón funcional del quemador correspondiente. * Al mismo tiempo que se mantiene activado, girarlo hacia la izquierda hasta fuego máximo, lo cual dejará salir el gas (posición de ignición). * El electrodo de ignición producirá chispas y cuando la mezcla de gas y aire sea correcta, el quemador se encenderá. Si no existe ninguna posibilidad de conectar la unidad con la línea principal, debe encenderse una cerilla.
Mantenimiento y limpieza Por razones de higiene y seguridad, las zonas de cocción deben estar siempre limpias. Las manchas de grasa y las pérdidas de comida generan humo al calentarse y también pueden causar incendio. Panel Desmontaje del panel El panel puede desmontarse para facilitar la limpieza de la superficie. Que hacer: 1. Sostener el panel de acuerdo con el diagrama. 2. Levantar el panel directamente hacia arriba. 3.
1. Quitar las manchas, etc., con ayuda del raspador de la placa cerámica. 2. Procurar que la placa se haya enfriado. Utilizar un agente limpiador cerámico. Sacudir la botella y aplicar dos o tres chorros en la placa cerámica. 3. Limpiar la placa cerámica con un paño húmedo o con papel de cocina. Las manchas duras se quitan frotando fuertemente con papel. 4. Limpiar el agente limpiador sobrante con un paño húmedo. 5. Limpiar con un paño seco si fuera necesario.
Después de raspar, pulir bien con el agente limpiador adjunto. cuidadosamente las tapas y la rejilla antes de volver a utilizar el hornillo de gas para que el rebose no se pegue en el esmalte/la pintura. Los defectos en la superficie vitrocerámica que puedan relacionarse con la descripción de arriba, no están cubiertos por la garantía. Advertencia: La hojita de aluminio y los utensilios de plástico no deben situarse sobre superficies calientes. La superficie no debe utilizarse como depósito.
Montaje Precaución: Para evitar accidentes, este aparato debe instalarse de acuerdo con las instrucciones de instalación. MIN 55 La placa puede montarse en cualquier cocina con un tablero de mesa cuyo espesor oscila entre 28 mm y 40 mm. Distancia La distancia entre la parte superior de la mesa y la carpintería de abajo, debe no ser inferior a 55 mm. Fijación Abrir las piezas de fijación lo suficiente como para poder colocarlas debajo del tablero.
No es necesario fijar la barra de refuerzo a la superficie de la mesa, ya que queda en su sitio mediante una pieza moldeada de diseño especial, que se ha incorporado a la bridas de la placa. Min. 140 mm Min. 16 mm Cinta de Aluminium-tape aluminio Instalación en superficies de mesa con una base por debajo Si la placa se va a instalar encima de una base, es necesario montar una tabla debajo de la placa (panel de 16 mm). Sellar todas las uniones con cinta de aluminio.
La placa no debe instalarse encima de cajones.
La longitud de la unidad, medidas externas 145 mm: Campana extractora 290 mm: Placa eléctrica de encimera vitrocerámica de dos zonas Placa de gas de dos quemadores Gratinador Freidora Wok 580 mm: Placa eléctrica de encimera vitrocerámica de cuatro zonas Placa de gas de cuatro quemadores 725 mm: Placa eléctrica de encimera vitrocerámica de cuatro zonas 16
Instalación de gas En conformidad con los requerimientos locales sobre aparatos domésticos de gas. La instalación de gas debe encargarse exclusivamente a una persona autorizada. Para los diferentes tipos de gas, véanse los datos técnicos. Conexión de gas La entrada de gas está situada en la parte posterior inferior. La toma tiene una rosca cónica para tubo de ½" (véase fig. 1). Si el aparato se conecta a un cilindro de gas, será necesaria una conversión mediante el equipo opcional de modificación.
Datos técnicos Tipo de gas Acondicionado para gas natural: G2020 mbar 1990, relativa a la aproximación de las legislaciones de los Estados Miembros sobre los aparatos de gas, la Directiva 73/23/CEE del Consejo, de 19 de febrero de 1973, relativa a la aproximación de las legislaciones de los Estados miembros sobre el material eléctrico destinado a utilizarse con determinados límites de tensión y la Directiva 89/336/CEE del Consejo, de 3 de mayo de 1989, sobre la aproximación de las legislaciones de los Esta
Servicio Antes de llamar al servicio – Asesoramiento técnico Pregunta: Respuesta: No hay ninguna chispa al encender el gas Controlar si la conexión de 230 V se ha enchufado. La vía del relé de circuito de falta a tierra se ha desconectado. El fusible se ha quemado. Cuando el botón funcional se activa, el anillo de gas se apaga El botón funcional no se ha pulsado el tiempo suficiente o no se ha pulsado lo suficiente. El anillo de gas quema muy inestable Controlar, p. ej.
325 88-1773 Rev.