BEDIENUNGS- UND INSTALLATIONSANLEITUNG 6561 G-m 1 AT DE 949600553
AEG beglückwünscht Sie Sehr geehrte Kunden, wir beglückwünschen Sie zum Kauf Ihrer neuen Kochmulde. Es ist wichtig, daß Sie die Funktionen und Finessen der Kochmulde gut kennenlernen. Lesen Sie deshalb diese Gebrauchsanweisung sorgfältig durch, damit Sie so viel Nutzen von Ihrer neuen Kochmulde haben wie möglich. Schenken Sie den mit gekennzeichneten Abschnitten besondere Aufmerksamkeit, dies sind Warnhinweise zur Verhütung von Unfällen. Bewahren Sie die Gebrauchsanweisung auf.
Inhaltsverzeichnis Inhalt Seite An den Anwender AEG beglückwünscht Sie ........................................................................... 2 Sicherheitshinweise ..................................................................................... 4 Beschreibung des Produkts ...................................................................... 6 So bedienen Sie ............................................................................................ 7 Brennerring/abdeckung .....................
Sicherheitshinweise Niemals Kunststoff- oder Aluminiumgeschirr für die Gaskochmulde verwenden. Diese Warnhinweise werden im Interesse Ihrer Sicherheit gegeben. Vergewissern Sie sich, daß Sie sie richtig verstanden haben, bevor Sie das Gerät installieren oder benutzen. Ihre Sicherheit steht an erster Stelle. Wenn Ihnen die Bedeutung dieser Warnhinweise unklar ist, wenden Sie sich bitte zwecks Klärung an die Kundendienstabteilung.
Entsorgung Die Gaskochmulde durch Abschneiden des Kabels unbrauchbar machen. Verpackungsmaterial und Altgeräte vorschriftsmäßig bei den entsprechenden Annahmestellen entsorgen.
Beschreibung des Produkts Brenner Lufteintrittsquerschnitt für primärluft Bedienungsschalter 6
So bedienen Sie Brennermarkierung An jedem Schalter gibt es Markierungen, welcher Brenner mit welchem Schalter reguliert wird. Symbole Vordere links Brenner: Hintere links Brenner: Hintere recht Brenner Vordere recht Brenner Panelmarkierung Jeder Schalter hat einen Skalaring mit Markierungen Abgeschaltete Stellung: Max. Flamme: Min.
Brennerring/-abdeckung Zusammen mit dem Brennerring bildet die Brennerabdeckung den Raum, in dem die endgültige Vermischung von Gas und Luft stattfindet, damit das Gas ordnungsgemäß brennen kann. Bitte beachten: Es ist daher sehr wichtig, daß die einzelnen Brennerabdeckungen/-ringe korrekt auf dem Brenner angebracht werden. Wenn die Brennerringe/-abdeckungen falsch angebracht sind, funktioniert der Brenner nicht richtig und kann innerhalb kurzer Zeit Schäden aufweisen.
Zündung Den Drehschalter für den betreffenden Brenner herunterdrücken. Den nach unten gedrückten Drehschalter gleichzeitig nach links in die Stellung “Größte Flamme” drehen, so daß das Gas ausströmt (Zündstellung). Die Zündelektrode erzeugt Funken, und wenn die Gas-Luft-Mischung richtig ist, wird der Brenner entzündet. Wenn es nicht möglich ist, die Einheit an die Stromversorgung anzuschließen, kann ein Streichholz verwendet werden.
Reinigung und Pflege von Aus Hygiene- und Sicherheitsgründen sind die Kochstellen sauber zu halten. Fettflecken und verschüttetes Kochgut qualmen beim Erhitzen und können im schlimmsten Fall ein Feuer verursachen. Ausbau von Paneel Sie können das Paneel ausbauen, damit sich dessen Reinigung einfacher gestaltet.
Flächen aus Edelstahl Für die alltägliche Reinigung benutzen Sie ein gut ausgewrungenes Tuch. Bei hartnäckiger Verschmutzung verwenden Sie ein flüssiges Scheuermittel. Die Reinigung muß immer in der Schleifrichtung des Stahls erfolgen. Um den Glanz des Stahls zu bewahren, empfehlen wir die regelmäßige Anwendung eines Poliermittels für Edelstahl; immer in der Schleifrichtung des Stahls polieren (in Querrichtung). Verwenden Sie nie Putzschwämme, Stahlwolle oder andere kratzende Reinigungsmittel.
Der Gasbrenner Die Bedienblende mit dem Drehschalter, der Topfträger und die Brennerabdeckungen/-ringe können mit gewöhnlichen Reinigungsmitteln gereinigt werden. Jedoch auf keinen Fall Scheuerpulver verwenden. Möglichst keine Töpfe überkochen lassen. Wenn doch einmal Wasser in den Brenner geraten ist, sollte dieses Wasser vor dem Wiederanzünden des Brenners entfernt werden, z.B. mit einem fusselfreien Tuch.
Montage Die Kochmulde kann in jeder Arbeitsplatte mit einer Dicke von 28 bis 40 mm montieret werden. Freie Höhe Der Abstand bis zu einem Zwischen/Einlegeboden oder der Obersiete eines Unterschrankes unter der Kochmulde soll mindestens 47 mm betragen. Festspannen Schrauben Sie die Beschläge zum Festspannen so weit heraus, dass die unter die Arbeitsplatte geschraubt werden können. Ziehen Sie die Beschläge mit einem Schraubenzieher fest an die Arbeitsplatte an.
Es ist nicht nötig, den Verstärkungsträger an der Arbeitsplatte zu befestigen, da er durch ein besonderes Formteil an den Flanschen der Kochmuldeneinheit gehalten wird. Einbau in eine Arbeitsplatte mit Unterschrank Soll die Kochmulde in eine Einheit mit Unterschrank eingebaut werden, muß eine Platte unter der Kochmulde angebracht werden (z.B. 16-mmSpanplatte). Min. 140 mm Min. 16 mm Aluminium-tape Alle Fugen mit Aluminiumband abdichten. Die Platte kann wie in der Abbildung dargestellt angebracht werden.
Kochmulden bitte nicht über Schubladen einbauen 15
Zusammenbau mit Ofen Falls der Ofen unmittelbar unter der Kochmulde angeordnet wird, ist ein Metallblech zwischen Ofen und Kochmulde zu montieren. Das Metallblech gehört zum Lieferumfang des bei dieser Kombination erforderlichen Einbausatzes. Den Satz mit der Produkt-Nr. 949 600 970 können Sie bei Ihrem Haushaltsgerätehändler bestellen. Dieser Brennerkörper lässt sich mit AEG CompetenceÖfen mit einer Höchstleistung von 3,7 kW kombinieren.
Die äusseren Breitenmaße der Einheiten 145 mm: Dunstabzug 290 mm: 2 Platten Glaskeramikmulde 2 Brenner Gas-mulde Glaskeramikgrill Single-Friteuse Kombigrill Wok 580 mm: 4 Platten Kochmulde 4 platten Glaskeramikmulde 4 Brenner Gas-mulde 725 mm: 4 platten Glaskeramikmulde Montage einer einzelnen Koch-mulde Bei der Montage einer einzelnen Kochmulde (mit 2 oder 4 Platten) in einer Arbeitsplatte, die dicker als 30 mm ist, muß für das Anschlusskabel auf beiden Seiten des Ausschnitts eine Aussparung angebracht we
Gasinstallation Gemäß den örtlichen Vorschriften für Haushaltgeräte zum Kochen mit Gas. Die Gasinstallation darf nur von hierfür zugelassenen Fachkräften ausgeführt werden. Siehe technische Daten zu Gastypen. Gasanschluss Der Gas-Einlass befindet sich hinten am Gerät unten. Der Einlass weist ein konisches ½-ZollGasgewinde auf (siehe Abb. 1). Falls das Gerät an eine Gasflasche anzuschließen ist, hat die Umrüstung mittels des als Zusatzausrüstung erhältlichen Nachbausatzes zu erfolgen.
Technische Daten Gastyp Eingestellt für Erdgas: G20-20 mbar Kennzeichnung in Übereinstimmung mit der Richtlinie über Gasverbrauchseinrichtungen (90/396/EWG), der Niederspannungsrichtlinie (73/23/ EWG) und der EMV-Richtlinie (89/ 336/EWG) einschließlich der vereinbarten Änderungen. Schutzklasse und Druck DE: II2ELL3B/P -20-50 mbar AT: II 2H3B/P - 20 -50 mbar Leitungstyp: 0,75 mm² HO5 V2V2-F Umstellbar auf Flaschengas G30-50 mbar Erdgas - G25-20mbar 230 V 1N + PE Max. Nennbelastung Q na.
Service Problem Mögliche Ursache Beim Einschalten des Gases wird kein Funke erzeugt Prüfen, ob die 230V-V-anschlußleitung eingesteckt ist. Das Erdschlußrelais hat sich ausgeschaltet. Die Sicherung ist durchgebrannt. Wenn der Drehschalter losgelassen wird, erlischt die Gasflamme wieder. Der Drehschalter wurde nicht lange genug oder nicht weit genug heruntergedrückt. Die Gasflamme brennt sehr unregelmäßig. Prüfen, ob de Abdeckung nach der Reinigung o.ä wieder richtig angebracht wurde.
24 325 88-3680 Rev.