INSTRUCTION- AND INSTALLATION BOOK 6562 G-m 1 AUS/NZL GB 949600573
Congratulations from AEG Dear Customer, Congratulations with your new Hob. It is important that you become familiar with the functions and features of the Hob. You should therefore read these operating instructions as they will help you get the most out of your new Hob. Pay extra attention to sections marked . These are warning texts to help you avoid accidents. Keep the operating instructions.
Table of contents Contents Page no For the user Your new appliance ...................................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 6 How to use .................................................................................................... 7 Burner ring................
Safety information Never use plastic or aluminium dishes on the gas hob. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. Never leave the gas hob unattended while deep fat frying, or heating fats and oils. Do not use or store flammable materials near this appliance.
Service Repairs carried out by inexperienced persons may cause injury or serious malfunction of the appliance. Repairs must only be carried out by a authorised person. Contact your local AEG Service Centre; 1 Stamford Road Oakleigh Victoria 3166 Telephone 1300 650020 Disposal Make the gas hob unusable by cutting off the cable Dispose of any packaging material and old appliances at an authorised disposal sites. The primary air intake aperture Must never be accidentally blocked by objects of any kind.
Description of the product Gas burner Control knob Air intake The primary air intake aperture must never be blocked by objests of any kind at any time.
How to use Burner markings Symbols at each operating knob indicate which burner is adjusted with the control knobs. Left front burner Left back burner Right back burner Right front burner Panel markings Each operating knob has a ring showing the scale of markings. Off.
Burner cover/burner ring Burner ring Together with the burner ring the burner cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Burner cover Correct Please note: It is consequently very important that the individual burner cover/ring is placed correctly on the burner. The burner ring has been provided with holes for the ignition electrode, and the thermo sensor.
Ignition 1. Depress and turn the control knob for the burner to the left to max. flame . (Ignition position) 2. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. If it is not possible to connect the unit to mains, a match may be used to ignite the burner. 3. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo-couple (thermo sensor ready). 5.
Cleaning and maintenance For reasons of hygiene and safety, the cooking zones must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. The splashguard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashguard as shown in the diagram. 2. Lift the splashguard straight up 3. Clean the top surface as described in “cleaning the steel surface”. Be aware of the two retaining pegs, which are sharp. 4.
3. Wipe the ceramic hob clean with a damp cloth or kitchen towel. Tough stains can be removed by rubbing the stain hard with kitchen towel. 4. Wipe off remaining cleaning agent with a damp cloth. 5. Wipe with a dry cloth, if required. Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid cream. Always clean the steel in the direction of the steel finish.
Cleaning of gas burners Clean the control panel and knobs plus the pan grid, as well as burner caps and rings, with ordinary cleansing agents. Never use scouring powder, Brillo pads, metal pads or other scouring agents on enamelled or painted surfaces! Avoid boil-over If water accidentally gets into the edge of the burner head (boil-over) the water must be removed with a lint-free cloth before the burner is turned on again.
Mounting This appliance must be installed by an authorised person. This appliance shall be installed in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, AS5601 (AG601) Australian Standard Gas Installations and any other relevant statutory regulations. Data label The data label is located on the underside of the hob next to the gas connection. A duplicate data label is supplied to adhere in an accessible area next to the hob.
Any adjoining wall surface situated within 200 mm from the edge of any hob burner must be a suitable noncombustible material for a height of 150 mm for the entire length of the hotplate. Any combustible construction above the hotplate must be at least 600 mm above the top of the burner and no construction shall be within 450 mm above the top of burner. A minimum depth of 60 mm from the top of the worktop surface must be provided for the hotplate.
Gas installation The appliance is factory set for Natural Gas. Fit the gas regulator supplied with the appliance to the gas inlet. The location of the gas inlet is approximately 240mm form the right hand side of the appliance and 40mm from the back of the appliance. The connection of the Gas Regulator is ½” Gas female thread and the pressure at the test point should be adjusted to1.00kPa with the large and simmer burners operating at maximum.
Use of Hose Assemblies. If the appliance is to be installed using a hose assembly, then 1. The hose must be AGA certified to AS/NZS 1869 as class B or class D, and utilised in accordance with requirements of AS 5601 (AG 601). 2. The connection point between the consumer piping and the hose must be accessible with the appliance installed. Electrical Connection This appliance is supplied with an 1800mm long flexible supply lead and 3 pin plug.
Before leaving The pipe connections should be checked for leaks with soap and water. Do not use a naked flame for detecting checks. Test all burners on high and low flame for flame stability. Test the stability of the low flame when any nearby cupboard doors are used. When satisfied with the appliance, please instruct the user on the correct method of operation. If the appliance fails to operate correctly after all checks have been made, refer to the authorised service provider in your area.
Technical data Type of gas Adjusted for natural gas: 1,0 kPa (test point pressure) Radio-noise reduction This unit observes the current EECdirective on radio noise reduction.
Service Sympton: Solution: There is no spark when lighting the gas? Check whether the 240 V connection has been plugged in. The ground fault circuit relay way have switched off. The fuse has blown When the operating knob is released the gas ring goes out again? The operating knob has not been depressed long enough, or has not been depressed sufficiently. The gas ring burns very unevenly? Ensure the cover has been replaced correctly, e.g. after cleaning.
374 4081 03 / 09.04 From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
