GB 325 88-3683 Rev. 1-401 INSTRUCTION- AND INSTALLATION BOOK From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
Congratulations from AEG Dear Customer, Congratulations with your new Hob. It is important that you become familiar with the functions and features of the Hob. You should therefore read these operating instructions as they will help you get the most out of your new Hob. Pay extra attention to sections marked . These are warning texts to help you avoid accidents. Keep the operating instructions.
Service If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Centre. Table of contents Contents Page no For the user IMPORTANT: If you call out an engineer to a fault caused by incorrect use or installation, a charge will be made even if the hob is under guarantee. Sympton: Solution There is no spark when lighting the gas Check hob is connected to the electricity supply. Check the fuse and replace if necessery.
Safety information These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. Never use plastic or aluminium dishes on the gas hob. Type of gas Adjusted to natural gas: G20 - 20 mbar Never leave the gas hob unattended while deep fat frying, or heating fats and oils.
Description of the product Gas installation In accordance with local requirements for domestic gas cooking appliances. Gas installation must only be carried out by an authorised person. For gas types see technical data. Gas connection The gas intake is situated at the lower rear of the appliance. The intake has a ½" conical pipe thread (see fig 1) If the appliance is to be connected to a gas cylinder, conversion with the optional modification kit will be necessary.
How to use The unit´s externally measured length Burner markings Symbols at each operating knob indicate which burner is adjusted with the control knobs. 145 mm: Cooker hood Left front burner 290 mm: Two-zone ceramic-top electric hob Two-burner gas hob Grill Fryer Wok Left back burner Right back burner Right front burner 580 mm: Four-zone ceramic-top electric hob Four-burner gas hob Panel markings Each operating knob has a ring showing the scale of markings. Off.
Burner ring/cover This gas hob can be combined with AEG Competence ovens with a maximum power of 3,8 kW. Together with the burner ring the burner ring/cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Please note: It is consequently very important that the individual burner cover/ring is placed correctly on the burner.
Ignition 1. Depress and turn the control knob for the burner to the left to max. flame . (Ignition position) 2. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. If it is not possible to connect the unit to mains, a match may be used to ignite the burner. 3. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo-couple (thermo sensor ready). 5.
Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation Maintenance and cleaning MIN 55 Mounting The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. For reasons of hygiene and safety, the cooking zones must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire.
Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid cream. Always clean the steel in the direction of the steel finish. To ensure that the steel retains its shine, it is recommended that you use a polishing agent for stainless steel on a regular basis. Always polish in the direction of the steel finish (crosswise). Never use steel wool, metal sponges or other abrasive cleaning agents. 3.
