66300KF-an Glaskeramik-Kochfeld Ceramic glass hob Table de cuisson vitrocéramique Montage- und Gebrauchsanweisung Installation and Operating Instructions Instructions de montage et mode d’emploi
Dear customer, Please read these operating instructions carefully. Pay particular attention to the section “Safety information” on the first few pages. Please retain these operating instructions for later reference. Pass them on to possible new owners of the appliance. 1 3 2 The following symbols are used in the text: Safety instructions Warning: Information concerning your personal safety. Important: Information on how to avoid damaging the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 The Key Features of Your Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Description of the Appliance . . . . . . . . . . . . . .
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regulations, Standards, Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Instructions for the Installer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions 1 Safety The safety aspects of this appliance comply with accepted technical standards and the German Appliance Safety Law. However, as manufacturers we also believe it is our responsibility to familiarise you with the following safety instructions. Electrical Safety 3 • The installation and connection of the new appliance must only be carried out by qualified personnel. • Repairs to the appliance are only to be carried out by approved service engineers.
• Overheated fats and oils catch fire quickly. You should supervise cooking when preparing foods in fat or oil (e.g. chips). • Switch off the cooking zones after use. Safety When Cleaning • For safety reasons do not clean the appliance with a steam jet or high pressure cleaner. • Clean the hob in accordance with the maintenance and cleaning instructions in this manual. How to avoid damage to the appliance • Do not use the cooking area as a worktop or storage space.
2 Disposal Disposing of the packaging material All materials used can be fully recycled. Plastics are marked as follows: • >PE< for polyethylene, as used for the outer wrapping and the bags inside. • >PS< for polystyrene foam, e.g., as used for the padding materials. They are completely free of CFCs. Disposal of old appliances 1 Warning: Before disposing of old appliances please make them inoperable so that they cannot be the source of danger.
The Key Features of Your Appliance • Ceramic glass cooking surface: The appliance has a ceramic glass cooking surface and 4 rapid response cooking zones. The particularly powerful radiant heater elements significantly shorten the amount of time taken for the zones to heat up. • Sensor fields: Your appliance is operated using Touch Control sensor fields. • Cleaning: The advantage of the ceramic glass cooking surface and the sensor fields is their accessibility for cleaning.
Description of the Appliance Cooking zones and control panel Single ring cooking zone 1200W Triple ring cooking zone 2300W Casserole zone 2400W Control panel Three-ring sensor panel „Block“ Three-ring control lamps sensor panel Sensor panel ”On/Off” Single ring cooking zone 1200W Browning zone sensor panel Browning zone control lamp “Timer” with Cooking setting Cooking setting control indicators selector selector Indicator for cooking setting/ residual warmth 45
Digital displays The four display panels that belong to the four cooking zones indicate: – ¾ after having been switched on, – u when a keep warm setting has been selected, – ¿ to Ç, depending on the cooking setting selected, – 2 to 6 (with decimal point) for intermediate cooking settings, – a when the automatic warm up function is in operation, – h when there is residual warmth, – l when the child safety device has been switched on, – e when there is a malfunction 1 Safety cut-out function for the cooking
Before Using for the First Time Initial Cleaning 1 Wipe the ceramic glass surface with a damp cloth. Important: Do not use any caustic, abrasive cleaners! The surface could be damaged. Operating the Hob Touch control sensor panels 3 To operate the touch control sensor panels, touch the desired panel with the tip of your pointed finger until the relevant displays illuminate or go out, or until the desired function is carried out.
Switching off the appliance To completely switch off the appliance, actuate the “On/Off” sensor panel I. Touch the “On/Off” sensor panel for approx. one second. 3 After switching off a single cooking zone or the entire cooking surface, the existing residual warmth will be displayed in the digital displays of the corresponding cooking zones in the form of h (for “hot”). Selecting cooking settings For setting and changing the cooking setting (u to Ç) for the selected cooking zone.
Keep warm setting Each of the 4 cooking zones has a keep warm setting u. Use the cooking setting selector sensor panel to set the keep warm setting u. Switching the casserole zone on and off 1. Set the desired cooking setting. 2. To switch the casserole zone on or off, place your finger flat on the “casserole zone” sensor field until the indicator light illuminates or goes off.
1. Set the desired cooking setting. 2. Touch the “triple ring” sensor panel. This will switch the setting to the centre heating ring. The lower control lamp will illuminate. 3. Touch the “triple ring” sensor panel to activate the outer heating ring. The upper control lamp will illuminate. 4. To switch off the outer heating ring, touch the “triple ring” sensor panel, and the heating ring that is outermost at the time will switch off.
Switching off a cooking zone 1. To switch off a cooking zone touch the cooking setting selector sensor panel and simultaneously, or return the setting to zero using the cooking setting selector sensor panel . Residual Heat Indicator 2 1 1 When an individual cooking zone or the entire hob is switched off, any residual heat is shown with an h (for “Hot”) in the digital display for the appropriate cooking zones.
Cooking using the automatic warm up function All of the cooking surface’s four cooking zones can be adjusted to any of nine settings, and are equipped with an automatic warm up function: – ¿, lowest cooking setting – Ç, highest cooking setting – a, automatic warm up function.
Cooking without the automatic warm up function If you wish to use the cooking zones without the automatic warm up function, select the desired cooking setting using the cooking setting selector sensor panel . 1. Touch the cooking setting selector sensor panel in order to set the desired cooking setting from Ç to ¿. 3 You can change the setting at any time using the cooking setting selector sensor panels and .
Child safety lock You can use the child safety lock to safeguard against unwanted use of the cooking surface. Switching on the child safety lock To be able to switch on the child safety lock the appliance must be switched on, but all the cooking zones must be switched off. 1. Touch the sensor field for approx. three seconds. An acoustic signal will sound as confirmation. 2. Touch any heat setting sensor field . l will appear in the displays, and the child safety lock is activated.
Overriding the child safety lock The child safety lock can be overridden in order to use the appliance (until the appliance is switched off again). When the appliance is switched on again the child safety device is activated once again. 1. Switch on the appliance. When the child safety device has been activated, l will be displayed. 2. Touch any two heat setting sensor fields and simultaneously. An acoustic signal will sound as confirmation.
Switching off the child safety lock 1. Switch on the appliance. When the child safety device has been activated, l will be displayed. 2. Touch the sensor field for approx. three seconds. An acoustic signal will sound as confirmation. 3. Touch any heat setting sensor field . The displays will become dark, and the child safety device is switched off. The appliance will switch itself off automatically after a few seconds.
Timer 3 There are two ways to use the timer: – as a safety cut-out function. Set a cooking period for a cooking zone, and after this time has elapsed the cooking zone will automatically switch itself off. This function can be used for more than one cooking zone simultaneously. – as a countdown timer without a cut-out function (“egg timer”), whereby an acoustic signal can be heard after the set period of time has elapsed. The countdown timer cannot be used if a cooking zone is switched on.
2. While the control lamp is flashing rapidly, use the or timersetting sensor panels to set the desired period of time for this cooking zone up until the point where it automatically switches itself off (e.g. 15 minutes). The safety cut-out function will be activated after several minutes The control lamp will now flash more slowly and the remaining cooking time will be shown in the display as it elapses.
Switching off the safety cut-out function before it has come to an end There are two ways to switch off the safety cut-out function before it has come to an end. Switch off the cooking zone and timer simultaneously 1. Using the cooking setting selector sensor panel, reset the desired cooking zone to zero: the cooking zone and timer will switch themselves off. Switch off the timer – the cooking zone remains active 1. Select the desired cooking zone using the timer sensor panel.
Blocking/unblocking the control panel At any stage of the cooking process the control panel, with the exception of the “On/Off” sensor panel, can be blocked in order to prevent the settings being changed e.g. by wiping over the panel with a cloth. 1. Touch the “block” sensor panel for approx. one second. 3 60 The control light for the “block” sensor panel will illuminate. The sensor panels are blocked. 2. To unblock the panel, touch the “block” sensor panel again for approx. one second.
Uses, Tables and Tips Pans The better the pan, the better the results. • You can recognise good pans by their bases. The base should be as thick and flat as possible. • Pay particular attention when buying new pans to the diameter of the base. Manufacturers often give only the diameter of the upper rim. • Pots with aluminium or copper bases can cause metallic discolouring on the glass ceramic surface, which is very difficult or impossible to remove.
• The base of the pan should be the same size as the cooking zone. • Using a pressure cooker reduces cooking times by up to 50%. Advice on Cooking with and without Automatic Warm up The automatic warm up function is suitable for: • dishes that start off cold, are heated up at high power and do not need to be continually watched when cooking on the selected heat setting, • dishes that are put in a hot frying pan.
Reference values for your cooking The figures in the following table are benchmark figures. The switch setting required for a certain cooking method depends on the quality of the pans and the type and amount of food. Switch setting Automatic warm up function1) (min.
Cleaning and Care Hob 1 3 Important: Cleaning agents must not come into contact with the hot ceramic glass surface! All cleaning agents must be removed with plenty of clean water after cleaning because they can have a caustic effect when the rings are next heated! Do not use any aggressive cleaners such as grill or oven sprays, coarse scourers or abrasive pan cleaners. Clean the ceramic glass surface after each use when it is warm to the touch or cold. This will avoid spillages becoming burnt on.
1 Problem Dirt 1. Remove burnt-on sugar, melted plastic, aluminium foil or other meltable materials with a glass scraper immediately and while still hot. 1 3 Important: There is a risk of burning yourself when the glass scraper is used on a hot cooking zone! 2. Then clean the hob normally when it has cooled down. If the cooking zone on which something has melted has already cooled down, warm it up again for cleaning.
What to do if … Rectifying faults 1 It is possible that faults have been caused by a minor error, which you can correct yourself with the help of the following instructions. Do not attempt any further repairs if the following instructions do not help in each specific case. Warning! Repairs to the appliance are only to be carried out by approved service engineers. Improperly effected repairs may result in considerable risk to the user.
… after having switched off the cooking zones, no h for residual warmth is indicated in the display. Check whether – the cooking zone was only briefly used and therefore did not become hot enough. If the cooking zone is hot, please call customer service. … a cooking zone will not switch off. Check whether – the sensor switches are partially covered by a damp cloth or liquid. – the blocking function is switched on. …a cooking zone will not switch on. Check whether – the child safety device is swiched on.
Installation Instructions 1 Important! The new appliance may only be installed and connected by qualified personnel. Please observe this instruction, otherwise the warranty will not cover any damage that may occur.
Regulations, Standards, Directives This appliance meets the following standards: • EN 60 335-1 and EN 60 335-2-6 relating to the safety of electrical appliances for household use and similar purposes and • EN 60350, or DIN 44546 / 44547 / 44548 relating to the operating features of electric cookers, hobs, ovens, and grills for household use. • EN 55014-2 • EN 55014 • EN 61000-3-2 • EN 61000-3-3 • relating to basic requirements for electro-magnetic compatibility protection (EMC).
1 Safety Instructions for the Installer • A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm. Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors. • In respect of fire protection, this appliance corresponds to EN 60 335-2-6.
Electrical Connection 1 Before connecting, check that the nominal voltage of the appliance, that is the voltage stated on the rating plate, corresponds to the available supply voltage. The rating plate is located on the lower casing of the hob. The heating element voltage is AC230V~. The appliance also works perfectly on older networks with AC220V~.
72
Service In the “What to do if …” section a number of malfunctions are listed that you can rectify yourself Look there first if a fault occurs. Is it a technical fault? If so, please contact your customer service centre. (You will find addresses and telephone numbers in the section “Customer Service Centres”.) Always prepare in advance for the discussion.
Montage / Assembly 110
111
From the Electrolux GroupK=qÜÉ=ïçêäÇ…ë=kçKN=ÅÜçáÅÉK qÜÉ=bäÉÅíêçäìñ=dêçìé=áë=íÜÉ=ïçêäÇ…ë=ä~êÖÉëí=éêçÇìÅÉê=çÑ=éçïÉêÉÇ=~ééäá~åÅÉë=Ñçê=âáíÅÜÉåI=ÅäÉ~åáåÖ=~åÇ=çìíÇççê ìëÉK= jçêÉ= íÜ~å= RR= ãáääáçå= bäÉÅíêçäìñ= dêçìé= éêçÇìÅíë= EëìÅÜ= ~ë= êÉÑêáÖÉê~íçêëI= ÅççâÉêëI= ï~ëÜáåÖ= ã~ÅÜáåÉëI î~Åììã=ÅäÉ~åÉêëI=ÅÜ~áå=ë~ïë=~åÇ=ä~ïå=ãçïÉêëF=~êÉ=ëçäÇ=É~ÅÜ=óÉ~ê=íç=~=î~äìÉ=çÑ=~ééêçñK=rpa=NQ=Äáääáçå=áå=ãçêÉ íÜ~å=NRM=ÅçìåíêáÉë=~êçìåÇ=íÜÉ=ïçêäÇK Hier Typenschild aufkleben (nur für Werk) AEG Hausgeräte GmbH Postfach 1036 D-90327 Nür