84602 G - 85600 G - 856001 G AUS ERFAHRUNG GUT Gas hob Table de cuisson Kochmulde Gaskookplaat Piano di cottura Operating Instructions Notice d’utilisation Gebrauchsanweisung Gebruiksaanwijzing Istruzioni per l’uso
ENGLISH Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 572700 Installation ● This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. ● Any gas installation must be carried out by a registered CORGI installer. ● Remove all packaging before using the hob.
Contents Guide to Use the instructions Important Safety Information .................................................................... 2 Instructions for the User .............................................................................. 6 Description of the Hob ........................................................................................... 6 Operation ....................................................................................................................
Description of the Hob 1 3 Operation 3 5 HOB BURNERS 6 7 To light a burner, turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner. Upon, ignition, adjust the flame as required. 8 If the burner does not ignite, turn the control knob to zero, and try again. i To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). 4 2 1. 2. 3. 4. 5. 6. 7. 8.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
Service and Spare Parts Guarantee Conditions If you require spare parts or an engineer contact your local Service Force Centre by telephoning: AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handled over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2.
Instructions for the Installer BURNER Engineer technical data TYPE OF GAS OVERALL DIMENSIONS Width: Depth: Height: Weight: 580 mm. 510 mm. 88 mm. 8 Kg. CUT OUT DIMENSIONS 550 mm. 470 mm. 30 mm. Width: Depth: Thickness: SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse.
Important safety requirements CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions.
Installation Cut Out Size The dimensions of the cut-out are given in the diagram. 0 58 FO 0814 51 0 FO 0264 A) End of shaft with nut B) Washer C) Elbow 0 55 On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection 47 0 55 m in. FO 2272 Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e.
Building in 1 Building in ON/OFF SWITCH Fitting the hob to the worktop 2 ON/OFF SWITCH Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below.
Electrical connections Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations.
Fault Finding Blue Brown Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Green Yellow Blue Green Yellow Brown A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts clean and tight. B.
Fault finding Ignition System / Gas Ignition Ignitor does not spark YES Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Check gas supply at burner ☞ NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted 1) Turn the gas tap to the MAX position and ignite.
Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit. Method ☞ 1) Ensure that the gas taps are in the 'OFF' position 2) Isolate the hob from the electricity supply 3) Remove all pan supports, burner caps, rings, crowns and control knobs.