ÖKO-LAVAMAT 86720 update The environmentally friendly washing machine Instruction book
Dear Customer, Please read this instruction book through carefully, before using the appliance. Please ensure you fully understand the safety instructions on the first pages of this instruction book! Retain the instruction book for future reference, and pass it on to any future owners. The warning triangle and/or the key words (Warning!, Caution!, Important!), emphasizes information which is important for your safety or the correct functioning of the appliance.
Contents CONTENTS Operating Instructions .................................... 6 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Environmental Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Program Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separate Fabric Softening/Starching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separate Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separate Spinning . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Installation and Connection Instructions . . . . . . . . . . . . . . . . 40 Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Appliance Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Front and Side Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions OPERATING INSTRUCTIONS 1 Safety Instructions Your safety is of paramount importance, please ensure you read these warnings before installing or using the appliance. If you are unsure about any of the meanings of these warnings, contact the Customer Care Department. Prior to Initial Start-up This appliance must be connected to the cold water supply only. Observe the "Installation and Connection Instructions" in this instruction book.
Operating Instructions Child Safety This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance. Pets and children have been known to climb into washing machines. Please check the drum before use. Keep all packaging well away from children. Keep all detergents in a safe place out of childrens reach. When disposing of the appliance, cut off the mains cable, and destroy the plug.
Operating Instructions 2 Disposal Packaging Dispose of the packaging material correctly. All packaging materials are environmentally friendly and can be disposed of without any danger to the environment. The external plastic covering and bags inside are made of polyethylene (marking >PE<). The padding is made of CFC free expanded polystyrene (marking >PS<).
Operating Instructions Description of the Appliance Front View Control panel Detergent dispenser drawer Rating plate (behind door) Door Flap in front of drain pump Height adjustable feet; back right: self adjusting foot Detergent Dispenser Drawer k Prewash detergent/ soaking agent or (water softening agent if used.
Operating Instructions Control Panel Program progress display Spin speed/ RINSE HOLD button DOOR/ LIGHT button Program selector START/ PAUSE button DELAY TIMER button Program option buttons Multi-display OVERDOSING indicator Program Selector The program selector defines the nature of the washing cycle (e.g. water level, drum movement, number of rinses, spin speed) to suit the type of washing, as well as the wash temperature. OFF Switches the washing machine off, in all other positions it is on.
Operating Instructions WOLLENS/P (Hand Washing) Main washing cycle (COLD to 40 °C) for machine washable wool as well as for hand washable woollen fabrics and silk with the care symbol ï (Hand washing). GENTLE RINSE Separate gentle rinse, e.g. for rinsing hand washed textiles (2 rinse cycles and short spin). STARCHING 1 Rinse with fabric softener or a starching agent. Additives from the compartment w are added. PUMP OUT Pumping out the water after a rinse hold (without spinning).
Operating Instructions STAIN For the treatment of extremely soiled washing or stained washing with stain remover. 3 When the setting WOOLENS/P is chosen, the program options cannot be selected (any buttons pressed do not have any effect). Consumption Data and Wash Times The values given in the following table for selected programmes were calculated under standard conditions. They provide a useful guide for operation in the home. Washload in kg Water in litre COTTONS/LINEN 95 5 39 1.
Operating Instructions Before Using for the First Time 0 1. Pull the detergent dispenser drawer a short distance out of the control panel. 2. Pour about 1 litre of water through the detergent dispenser drawer into the washing machine. When this has been done, done the ÖKO lock can function correctly. 3. Run a washing cycle without washing (COTTONS 95, with half the amount of washing powder). This removes any residues from the drum which may have been left during manufacture.
Operating Instructions Shake out washing before placing into the washing machine. Do not place folded washing into the drum. Observe tips such as "wash separately" and "wash separately several times"! Washing Types and Care Symbols Care symbols assist in the selection of the correct washing program. Washing should be sorted according to type and care symbol. The temperatures indicated in the care symbols are maximum temperatures.
Operating Instructions Which Detergent? To ensure you obtain the best wash results from your appliance, it is important to use the right detergent in your everyday wash, and only detergents recommended for use in automatic machines. To maintain the appearance of your clothes and household textiles and to make them last longer you should use different types of detergent for different washes whether for whites, colours or delicates.
Operating Instructions And in which form? Not only are there different types of detergent, but they are also available in different forms. Whether you choose a powder or liquid in traditional or compact form, is down to personal choice. Traditional Powders Pour the powder directly into the dispenser drawer. Do not sprinkle powder onto clothes in the machine drum.
Operating Instructions How much Detergent and Fabric Softener? The amount to be used depends on the load: If the detergent manufacturer does not make any specifications for small loads, use a third less for half loads, and for very small loads only use half of the amount of washing powder recommended for a full load. the soiling: For only lightly soiled washing use less washing powder. Follow the instructions of the detergent manufacturer and load.
Operating Instructions Running a Wash Cycle Brief Instructions A washing cycle consists of the following steps: 0 1. Set the correct washing program: select the program and the temperature with the program selector select additional program(s) if required 2. If necessary change the spin speed/select RINSE HOLD). 3. Set time delay if required. 4. Open the door, insert washing. 5. Shut the door. 6. Add detergent/conditioner. 7. Start washing program.
Operating Instructions Setting the Washing Program See "Program tables" for suitable program, correct temperature and any possible program options for the respective type of washing. 0 1. Set program selector to the desired program with the desired temperature. The estimated duration of the selected program appears in the multi-display in minutes. 3 2. If applicable select program options: The displays of the program options selected lights up. To change the selection press another button.
Operating Instructions Setting a Time Delay 0 If applicable set the delay timer: press the DELAY TIMER button repeatedly until the time delay required is displayed in the multidisplay, for example 12h for a 12 hour delay start of the program. If 19h is displayed and you press the button again the running time of the currently set washing program appears and the delay start is cancelled. If the SOAKING option is selected the delay timer determines the soaking time.
Operating Instructions Add Detergent/Conditioner For instructions concerning detergents and conditioners see "Which Detergent", And in which form. 0 1. Open the detergent dispenser drawer: press in the flap on the drawer so as to be able to grasp the handle (1), pull out the drawer (2). 2. Add detergent/conditioner. 3 k Pre-wash detergent/detergent for soaking (for program options PRE WASH/ SOAKING), or water softening agent.
Operating Instructions Start Washing Program 0 1. Check whether the water tap is opened. 2. Start washing program: Press START/PAUSE button. The washing program is started or starts at the end of the delay time set. 3 If the DOOR/LIGHT display flashes red when the START/PAUSE button is pressed, the door is not properly closed. Close the door firmly and press the START/PAUSE button again.
Operating Instructions Washing Program Sequence Program Progress Display Prior to the start, the program steps chosen are displayed on the program progress display. During the washing program the current program step is displayed. Multi-display The expected time remaining (in minutes) to the end of the program is displayed in the multi-display.
Operating Instructions End of Wash Cycle/Removing the Washing Once the washing program has come to an end, END illuminates on the program progress display. If RINSE HOLD was selected, the indicator beside the START/PAUSE button flashes. 0 1.
Operating Instructions Program Tables Washing Not all possible settings are given in the following, but only those that are useful and meaningful in everyday use. Type of Washing, Care Symbol Max.
Operating Instructions Separate Fabric Softening/Starching Type of Washing Cottons/Linen Max. Load (Weight Dry) Program Selector 5kg Easy-Cares 2.5kg Delicates 2.5kg STARCHING Separate Rinsing Type of Washing Cottons/Linen Max. Load (Weight Dry) 5kg Easy-Cares 2.5kg Delicates 2.5kg Woollens/Hand Washing Program Selector GENTLE RINSE 1kg Separate Spinning Type of Washing Cottons/Linen Program Selector 5kg SPIN Easy-Cares 2.5kg Delicates 2.5kg Woollens/Hand Washing 26 Max.
Operating Instructions Maintenance and Cleaning Control Panel Important! Do not use household furniture polish or abrasive cleaners to clean the panel and operating parts. Wipe over the operating panel with a damp cloth. Use warm water. 0 Detergent Dispenser Drawer The detergent dispenser drawer should be cleaned from time to time. 0 1. Pull the detergent dispenser drawer out as far as it will go. 2. Remove the detergent dispenser drawer by pulling sharply. 3. Remove the suction cap. Suction cap 4.
Operating Instructions What to do when 3 The whistling noise when spinning may be different to your prevous washing machine which is due to the modern drive system. Trouble Shooting If you call out an engineer and the fault is listed here, a charge is levied even if the appliance is in guarantee. If the error code (1, (2 or (d is displayed in the multi-display, check the troubleshooting guide below before calling an engineer. After eliminating the error, press the START/PAUSE button.
Operating Instructions Malfunction Possible Cause The machine is not level. Washing machine vibrates during operation or is unstable. Remedy Adjust the feet according to the installation and connection instruction. There is only very little washing in the machine (e.g. only Does not impair function. a bath robe). Water could not be completely pumped out prior to spinning because the drain hose is kinked or the drain pump is blocked.
Operating Instructions Malfunction The door cannot be opened with the machine on. Possible Cause Remedy Door is locked due to safety reasons (lamp next to the DOOR/LIGHT button is off). Wait until the lamp is green. Cancel the child safety The child safety device is set. device (see "Child safety device"). Tap is not fully open. The inlet hose filter in the Remnants of detergent coupling of the inlet hose at are building up in the the tap is blocked. detergent dispenser drawer.
Operating Instructions If the Washing Results are not Satisfactory If the washing turns greyish and limescale deposits are present in the drum Insufficient washing powder has been added. Incorrect washing powder was used. Stains were not pretreated. Program or temperature was not set correctly. When using modular washing powders the individual components were not used in the correct ratio.
Operating Instructions Carrying out an Emergency Emptying If the washing machine no longer pumps out the water an emergency emptying must be carried out. If the washing machine is located in a room in which below freezing temperatures might occur, emergency emptying must be carried out if danger of freezing occurs. Furthermore, the inlet hose must be disconnected from the tap, drained and laid on the floor. Warning! Switch the washing machine off and pull the mains plug prior to emergency draining.
Operating Instructions When the Water is Completely Drained: 7. Push and twist the plug firmly back into the emergency emptying hose. 8. Push the emergency emptying hose back in a little and let it catch on to the holder. 9. Put on the flap and close. The ÖKO lock does not function when the machine has been fully emptied. Therefore add approx. 1 liter of water before the next wash (pour in through the detergent dispenser drawer).
Operating Instructions Unlocking the Door in an Emergency If the door cannot be opened (e.g. due to a faulty door lock or due to a power cut during the washing program), it can be opened using the emergency unlock feature. 0 1. If water can be seen in the window of the door first carry out an emergency emptying (see section "Carrying out an emergency emptying"). 2. Turn the knob anti-clockwise with the help of a coin or a screwdriver. The door opens.
Operating Instructions When the additional rinse function is selected, the RINSE+ indicator on the program progress display illuminates prior to program start and during the additional rinse. 4. If you wish to check whether the additional rinse function is selected: Turn the program selector to SHORT SPIN. Press the SOAKING button briefly. If RINSE+ flashes on the program progress display, the additional rinse function is set. Disabling the Additional Rinse Function: 0 1.
Operating Instructions Switching off Wash-Water Cooling: 0 1. Turn the program selector to SHORT SPIN. 2. Press the PRE WASH button for at least 5 seconds. As soon as the button is pressed MAINWASH flashes on the program progress display. After 5 seconds MAINWASH ceases to flash and illuminates continuously for 5 seconds. 3. Whilst MAINWASH is continuously illuminated, release the PRE WASH button. Once MAINWASH has ceased to illuminate, the wash-water cooling function is disabled.
Operating Instructions Child Safety Device In order to protect a program setting from being accidentally changed (e.g. turning the program selector, pressing extra keys, etc.), you can set the child safety device. This prevents children from damaging your washing. 3 The child safety device can also be set and cancelled whilst a program is running. Set the Child Safety Device: 0 1. Set the desired program. 2. Press the START/PAUSE button to start the program. 3.
Service & Spare Parts SERVICE & SPARE PARTS If after carrying out the necessary checks there is still a fault with your appliance please contact your local AEG Service Force Centre. In guarantee customers should ensure that the suggested checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that proof of purchase is required for in-guarantee service calls.
Guarantee Conditions GUARANTEE CONDITIONS 1. 2. 3. 4. 5. 6. Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installation Safety Precautions This appliance is heavy, care should be taken when moving it. When moving, do not tip the washing machine onto its front or left hand side (viewed from the front). This is to prevent the possibility of electrical components becoming wet. Before installation inspect the machine for transport damage. Do not connect the appliance if it is damaged contact your retailer.
Installation and Connection Instructions Appliance Dimensions Front and Side Views Rear View Important! This appliance must be connected to the cold water supply only.
Installation and Connection Instructions Appliance Installation 3 The appliance worktop must not be removed to gain a height reduction when installing under a kitchen worktop. Appliance Transit To prevent electrical components becoming wet when moving the appliance, do not tip the washing machine onto its front or the left hand side (viewed from the front). Do not transport the appliance without the transit packaging/bolts/ bar in place.
Installation and Connection Instructions Removing Transit Packaging Important! Ensure all transit packaging is removed prior to installation. Retain transit packaging for future use. The appliance is supplied with a spanner (H) and plastic caps (E) (2 pcs.) and (G) (1 pc). 0 1. Remove the hose holder (A). 2. Remove the 2 screws (B) with the spanner supplied (H). 3. Remove the 4 screws (C). 4. Remove the transit bar (D). 5. Cover the holes left by screws (B) the 2 plastic caps (E).
Installation and Connection Instructions Installation-Site Preparation The installation surface must be clean, dry and level. Do not install on deep pile carpet. If the appliance is installed next to heat source (e. g. cooking appliance), a heat insulating pad (85 x 57 cm) must be placed between the washing machine and the heat source. Do not install the appliance in locations where the temperature may fall below freezing.
Installation and Connection Instructions Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. 1 WARNING - THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The rating plate is located at the top of the rim of the open door.
Installation and Connection Instructions Permanent Connection In the case of a permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations. The switch must not break the yellow and green earth cable at any point.
Installation and Connection Instructions Water Connection 3 The washing machine is provided with safety devices preventing backcontamination of the water supply and complies with local water authority requirements. This appliance is designed to be permanently plumbed into your homes water supply. Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes.
Installation and Connection Instructions Inlet Hose Connection Important! This appliance must be connected to the cold water supply only. The inlet hose provided is 1.2 or 1.3 metres depending on the model. If a longer inlet hose is required contact your AEG Service Force Centre. Under no circumstances should hoses be connected together to provide a longer length. The rubber washers are either set into the inlet hose threaded connection or supplied separately in the installation kit.
Installation and Connection Instructions Water Drainage The upright standpipe should have a minimum, length of 30 cm (12) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water. Longer drain hoses are available in lengths of 2.7 and 4 metres from your AEG Service Force Centre.
Installation and Connection Instructions Technical Data Height x Width x Depth Depth with open door Height adjustment Weight when empty Load (depending on the program) Area of use Wash cycle drum speed Spin cycle drum speed Water pressure 85x60x60cm 95cm approx. +10/-5mm approx. 85kg max. 5kg Household max. 53min-1 r.p.m. see rating plate 1-10bar (=10100N/cm2 = 0.1 1.
Index INDEX A Additional rinse . . . . . . . . . . . . . . . . . . . . . . 34 Aqua control with aqua alarm . . . . . . . . . 24 C Cancel program . . . . . . . . . . . . . . . . . . . . . . 23 Child safety device . . . . . . . . 20, 24, 30, 37 Conditioner . . . . . . . . . . . . . . . . . . 14, 16, 21 liquid . . . . . . . . . . . . . . . . . . . . . . . . . .9, 21 Cottons . . . . . . . . . . . . . . . . . . 10, 14, 25, 26 Customer care . . . . . . . . . . . . . . . . . . . . . . .
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.
