Operation Manual

6
TECHNICAL DATA Power screwdriver
 
Rated input ...........................................................
Output ...................................................................
No-load speed ......................................................
Speed under load max. ........................................
Static jamming moment ........................................
Drilling capacity in steel ........................................
Drilling capacity in aluminium ...............................
Drilling capacity in wood ......................................
Drill opening range ...............................................
Drive shank...........................................................
Weight without cable ............................................
GB
English
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signicantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signicantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
The dust produced when using this tool may be harmful
to health. Do not inhale the dust. Wear a suitable dust
protection mask.
The drill/screwdriver can be universally used for drilling, and
screwdriving.
Do not use this product in any other way as stated for normal
use.
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 2006/42/EC, 2004/108/EC
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact as
the design conforms to safety class II.
WARNING!
R ead all safety warnings and all instructions, including
those given in the accompanying brochure. Failure to
follow the warnings and instructions may result in electric
shock, re and/or serious injury. Save all warnings and
instructions for future reference.
Wear ear protectors. Exposure to noise can cause hearing
loss.
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will also make exposed metal parts of the power
tool “live” and shock the operator.
Appliances used at many different locations including open
air should be connected via a residual current device of
30 mA or less.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
When working in walls ceiling, or oor, take care to avoid
electric cables and gas or waterpipes.
SAFETY INSTRUCTIONS
SPECIFIED CONDITIONS OF USE
EC-DECLARATION OF CONFORMITY
MAINS CONNECTION
Noise/vibration information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A))
.......................
Sound power level (K = 3 dB(A)) ...........................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Drilling into metal: Vibration emission value a
h
......
Uncertainty K= .......................................................
Screwing: Vibration emission value a
h
..................
Uncertainty K= .......................................................
 BE705R
..705 W
...566 W
.2700 min
-1
.1820 min
-1
.....15 Nm
.....10 mm
.....16 mm
.....30 mm
. 1-10 mm
....1/2 “
....1,6 kg
..........85 dB (A)
..........96 dB (A)
..... < 2,5 m/s
2
.........1,5 m/s
2
..... < 2,5 m/s
2
.........1,5 m/s
2
Rainer Kumpf
Manager Product Development
Authorized to compile the technical file
Winnenden, 2010-02-24