34942G/35940G/35941G/35944G AUS ERFAHRUNG GUT Gas hob Table de cuisson Kochmulde Gaskookplaat Piano di cottura Operating and Installation Instructions GB Notice d’utilisation et d’encastrement FR/BE Gebrauchs- und Einbauanweisung BE Gebruiksaanwijzing en Installatievoorschrift NL/BE Istruzioni per l’uso e l’installazione IT
ENGLISH GB Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350 350 Installation ● This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. ● Any gas installation must be carried out by a registered CORGI installer. ● Remove all packaging before using the hob.
● When in use a gas cooking hob will produce heat and moisture in the room in which it has been installed. Ensure there is a continuous air supply, keeping air vents in good condition or installing a cooker hood with a venting hose. ● When using the hob for a long period of time, the ventilation should be improved, by opening a window or increasing the extractor speed. ● Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.
Contents Important Safety Information .................................................................... 2 Instructions for the User.............................................................................. 6 Description of the Hob ........................................................................................... 6 Operation ....................................................................................................................7 Maintenance and Cleaning ...........................
Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions ☞ i Step by step instructions for an operation Hints and Tips This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC 89/336 EEC - 90/396 EEC, current edition.
Description of the Hob (Mod. 34942 G) 1 3 2 3 4 1. Hob Top 5 2. Rapid Burner 3. Semi-rapid Burners 4. Double-crown Burner 5. Auxiliary Burner 6. Control knob for back left burner (semi-rapid) 7. Control knob for back right burner (semi-rapid) 8. Control knob for ront right burner (auxiliary) 9. Control knob for central burner (double-crown) 10.
Operation HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to the maximum position ( ), then push it down to ignite the burner. Upon, ignition, adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. i When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM ■ There is no spark when lighting the gas SOLUTION ◆ ◆ ◆ ◆ ■ The gas ring burns unevenly ◆ ◆ Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning.
Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to the your local Service Force Centre. When you contact the Service Centre, they will need the following information: 1. Your name, address and post code. 2. Your telephone number 3. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction booklet) 5.
Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: Height: Weight: 860 mm. 500 mm. 88 mm. 8 Kg. CUT OUT DIMENSIONS 830 mm. 470 mm. 30 mm. Width: Depth: Thickness: SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. IGNITION HT SPARK Spark Generator Ispra Control's BF 50066 - 230-240V 0.
BURNER RAPID (large) TYPE OF GAS POSITION NATURAL GAS 20 mbar VALUE = 37.78 MJ/m3 Ws - 50.7 MJ/ m3 LPG GAS 28-30/37 mbar VALUE = 49.92 MJ/Kg SEMI-RAPID (medium) AUXILIARY (small) DOUBLE CROWN MAX MIN MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 3.0 0.65 2.0 0.45 1.0 0.33 3.5 1.2 NOMINAL FLOW RATE m3/h 0.286 0.057 0.190 0.038 0.095 0.028 0.333 0.114 119 Adjust. 96 Adjust. 70 Adjust. 136 Adjust. NOMINAL THERMAL POWER kW 2.8 0.65 2.0 0.45 1.0 0.33 3.5 1.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 700mm mm 700 mm 400 mm 400 mm 55 50 m mm m 100 100 400 mm mm 50 m 50 m m FO 2027* mm m 400 mm mm 55 50 m m FO 2028* Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer.
Installation FO 0814 FO 0264 A) End of shaft with nut B) Washer C) Elbow this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper.
Cut Out Size The dimensions of the cut-out are given in the diagram. 0 50 0 47 86 0 83 0 n. i 5m 5 FO 2407 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 (see next page).
Building in 1 ON/OFF SWITCH 2 ON/OFF SWITCH FLEX OUTLET FLEX OUTLET FO 0764 FO 0763 Building over a kitchen unit with door 3 a 60 The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 20 min 30 Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated.
Building in Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. ☞ a Seal 1) Place the sealing gasket all around the edge of the cut out. 2) Place the hob into the cut out and secure it by means of the relevant fixing clamps and screws, as shown in the diagram.
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate.
Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. C.
Fault Finding Blue Brown Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. NO YES Blue Green Yellow Brown Carry out: D: Resistance to Earth check. Carry out: C: Polarity check. Has inlet fuse blown? NO Electricity supply should now be satisfactory. YES SOCKET (face view) PLUG (with cover removed) Earth Wire Green/Yellow Neutral Wire Blue ( ) E( ) FUSE Inlet wiring faulty. Rectify any fault.
A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight. B. INSULATION CHECK Appliance electrically disconnected, all switches ON. a) meter set on Ω (Ohms) x 1 scale. Test leads from L to N in appliance terminal block.
Fault finding Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check earth continuity of appliance Check position of the electrode Check fitting of burners Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from the tip of each electrode to the terminals 1 to 5 o
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. ☞ 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: ☞ 1) Re-ignite the burner and set to MIN. 2) Remove the control knob.
Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit. Method ☞ 1) Ensure that the gas taps are in the 'OFF' position 2) Isolate the hob from the electricity supply 3) Remove all pan supports, burner caps, rings, crowns and control knobs.