FR RENSEIGNEMENTS GENERAUX DESTINES A L’UTILISATEUR CONSEILS ET AVERTISSEMENTS D’ORDRE GENERAL AV E RT I S S E M E N T S P O U R L ' E N V I RO N N E M E N T ATTENTION: - N'oubliez pas, avant d'utiliser l'appareil, d'enlever le film de plastique qui protège certaines pièces (tableau de bord, cadres en inox, etc). - Ne pas utiliser l'appareil pour chauffer la pièce. - Lorsque l'appareil n'est pas utilisé, débrancher le courant et fermer le robinet général du gaz.
FR PREMIERE PARTIE UTILISATION DU FOUR ELECTRIQUE UTILISATION DE LA TABLE DE TRAVAIL PREMIERE PARTIE UTILISATION DES BRULEURS A GAZ Les symboles suivants se trouvent sur le bandeau de commande, près de chaque bouton: - Disque plein robinet fermé - Grande flamme ouverture maximale - Petite flamme ouverture minimale Quand le four est utilisé pour la première fois, il peut se produire de la fumée de odeur âcre, causée par le premier chauffage du collant des panneaux isolants autour du four (il est oppo
FR 1 - Manette thermostat combiné avec le commutateur du four Utilisation du four Note: fours avec thermostat et commutateur séparés. Lorsqu’on utilise les fonctions placer la manette du thermostat entre 180 ÷ 200°C comme température maximale. FOURS A CONVENTION NATURELLE Le four est pourvu de: • une résistance inférieure; • une résistance supérieure.
FR Utilisation du grilloir électrique L’appareil est prévu pour griller à porte entre ouverte (fig.2) avec la grille porte-plats au troisième gradin en partant du fond du four, à 12 cm à peu près de la surface rayonnante et le déflecteur en place comme en (fig.2). L’utilisateur pourra changer de gradin, suivant son goût personnel et les nécessités des différents mets. Avant d’enfourner, laisser chauffer 5 minutes.
FR fin de cuisson. Le temps de fin cuisson le plus proche apparaît sur l’affichage lumineux. Sélectionner le temps de fin cuisson désiré à travers le bouton +. Le relais et le symbole de durée se débranchent. Les symboles AUTO et durée de cuisson apparaissent en permanence. Les contacts du relais se débranchent. Quand le temps de fin cuisson correspond à l’heure, le relais et le symbole de durée de cuisson se débranchent.
FR Rétablissement du temporisateur Appuyer en même temps sur les boutons “+” et “-”. Relâcher avant le bouton “+”. Signal Quand le temps choisi sera échu, le signal retentira pendant 7 minutes. Pour l’arrêter appuyer sur le bouton “+” (un seul coup). Fréquence signal Quand l’affichage montre l’horaire du jour, la fréquence du signal peut être sélectionnée en appuyant sur le bouton “-”. On peut sélectionner 3 fréquences différentes.
FR Fig. 9 1/2” Fig. 8 VENTILATION LOCAUX Fig. 8 - le raccordement rigide avec interposition d’un joint; le raccordement par tuyau flexible avec armature à embouts mécaniques suivant les normes en vigueur. Le tube doit être raccordé directement au coude de la rampe. (voir fig 9 ). - le raccordement rigide avec interposition d’un joint; - le raccordement par tuyau flexible avec armature à embouts mécaniques suivant les normes en vigueur.
FR REGLAGES GAZ BRANCHEMENT ELECTRIQUE Si l'appareil a été prévu pour fonctionner avec un type de gaz différent de celui de l'alimentation disponible, il faut changer les injecteurs, règler le débit réduit des brûleurs et changer l'about annelé. Afin de changer les injecteurs de la table de travail, il est nécessaire d'effectuer les opérations suivantes: enlever les grilles, enlever les brûleurs et leurs chapeaux (voir fig.
FR ENTRETIEN DE L’APPAREIL - Pour démonter le tableau de bord il suffit de dévisser les 4 vis (B) internes qui fixent le tableau de bord à la façade du four (fig.16). AVERTISSEMENTS Avant d'effectuer toute réparation ou intervention, débrancher la prise de courant et fermer le robinet du gaz. Le constructeur décline toute responsabilité quant aux dommages subis par des personnes, des animaux ou des biens, résultant de la non observation des normes ci-dessus indiquées.
GB GENERAL INFORMATION DESTINED TO THE END USER RECCOMANDATIONS AND PRECAUTIONS FIRST PART ENVIRONMENT PROTECTION ATTENTION: - Before using the appliance, do not forget to remove the plastic films protecting some parts of the appliance (facia-panel, parts in stainless steel, etc.) - Do not use the appliance as a space heater. - When the appliance is not in use, we recommend to disconnect the current and to close the gas general tap.