CHDE 3160 Cooker hood Operating and Installation Instructions
Contents Safety warnings For the User For the Installer 4 4 4 Description of the Appliance Extractor version Filter Version 6 6 7 Control Panel 8 Maintenance and care Cleaning the hood Metal grease filter Removing the metal grease filter Charcoal filter Changing the light bulb 9 9 9 9 10 11 What to do if 12 Service and Spare Parts 13 Guarantee Conditions 14 Technical Specifications Mounting accessories included 16 16 Electrical connection Installing the hood between cupboards with hanging ra
Safety warnings For the User • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. • Also, when frying, keep the deep frying pan on the cooker top/ cooker under careful control. • The hot oil in the frying pan might ignite due to overheating.
• When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole. • National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room.
Description of the Appliance • The hood is supplied as an extractor unit and can also be used with a filtering function by fitting one charcoal filter. • You will need an original AEG charcoal filter for this function (Available from your local AEG Service Force Centre). Extractor version • In this version fumes are extracted to the outside via a hose connected to the coupling ring A, placed in the outlet hole B. Fig. 1.
Filter Version • The air is filtered through a charcoal filter and returned to the kitchen. • You will need an original AEG charcoal filter for the filtering function. (Available from your local AEG Service Force Centre). • Remove the grease filters, first pull the handles upwards, then extract the filter outwards. Fig. 3. E Fig. 3 E Fig. 4 E • Fit the charcoal filter first in the upper hooks into the lower, then lock in position using tabs E. Fig. 4. • Refit the grease filters.
Control Panel • Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared.
Maintenance and care • The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood • Clean the outside of the hood using a damp cloth and a mild detergent. • Never use corrosive, abrasive or flammable cleaning products. • Never insert pointed objects in the motor’s protective grid. • Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders.
Dishwasher Place grease filters in dishwasher. Select the most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. • Clean the inner housing using a hot detergent solution only (never use corrosive, abrasive or flammable cleaning products).
Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulb • • • • • 10 Disconnect the cooker hood from the mains supply. Remove the grease filters so to access the bulbs.
What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively.. . Check that: The fan speed is set high enough for the task. The grease filters are clean. The kitchen is adequately vented to allow the entry of fresh air.
Service and spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk Please ensure that you have read the section „What to do if....
Guarantee conditions Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation.The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances.
Technical Specifications Dimensions: (in cm): Height Width Depth 40 59,9 27 Maximum absorbed power: 200 W Motor absorption: Lighting: 120 W 2 x 40 W Length of the cable: 150 cm Mounting accessories included 1 Flange Ø 100 mm 1 Flange Ø 120 mm 2 Hooks 2 rails 1 Deflector 2 Washers 4 wood-screws 5 x 45 mm 4 Wall plugs Ø 8 mm 1 Metal-screw 2,9 x 9,5 6 wood-screws 4,5x16 10 wood-screws 4,5x13 1 Spacer Electrical connection Safety warnings for the electrician The electric outlet should be placed inside
Installing the hood between cupboards with hanging rails • Remove the grease filters. Fig. 6. • Take off the visor G. Fig. 13. • Mount the two hanging rails directly underneath the edge of the cupboard using three screws 4,5 x 16 mm in each rail. Distance from first hole to front edge of the cupboards sides must be 153 mm. Fig. 8. 153 Fig.
Installing the hood to the wall It is possible to fix the hood in position, if necessary, by only attaching it to the rear wall. Proceed as follows: • Drill four Ø 8mm holes on the wall as indicated. Fig. 10. 600 34,8 35 529 509,5 Fig. 10 • Insert the four wall plugs supplied into these holes. • Screw the two mountings hooks P into the top two wall plugs. Fig. 11. P U T S 0-90 54-100 0-54 R N Fig.
• Fix the base spacer M to the wall with the two screws R 5x45 provided using either the long or the short arm, depending on the depht of the side cupboards. Do not tighten the screws fully. Fig. 11. • Fix the hood to the wall by means of the two hooks P previously mounted, but first move the upper brackets S so that the front panel of the hood, once mounted, will be in line with the front edge of the cupboard doors.
H G Fig. 13 • Draw a line with a pencil on the middle of the internal side of the furnituture door. Fig. 14. = = L Fig. 14 • Fit the visor upon the internal side of the furniture door so that the line previously marked on it, is visible through the two triangles holes located on the mid upper and lower side of the visor, having care to respect the distance from the visor to the higher edge of the furniture door as for the reason mentioned above in Fig. 12.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de © Copyright by AEG LI1W1B Ed.
