ENGLISH Please read these instructions carefully before proceeding to install and use your cooker hood. This manual contains precise instructions on how to carry out the necessary preparatory and installation work, how to change the filters and how to operate the cooker hood.
Standard mode! The appliance is supplied as an air-extraction unit. Accessories (Packed separately) Various fixing screws, pipe connections. Special accessories Exhaust-air hose, exhaust-air pipe, wall box, clean-air cartridge, obtainable from retailers or AEG sales branches. Alr extraction Cooking fumes are dusted into an air shaft or directly to the outside of the building; through exhaust-air pipe or hose, 100 mm id, MKT wall box, E-No: 610899 003.
Alr outset: a On air-extraction unit: Either through the top or through the back. Connection must be made to either an air shaft or a ventilation aperture in the outer wall, Connection must not be made to a waste-gas fie or chimney. by On airletters unit: Through the ventilation rifle in the top of the hind. Make sure that this grille is never obstructed. important! Cooker hoods must be installed in accordance with pertinent regulations {e. g.
instructions for use Fig. 1 Fig. 2 Switch functions The cooker hood is operated by means of the knob (2) on the switch fascia panel.
Opening the appliance for cleaning purposes or in order to change the grease filer, the light bulb or the clean-air cartridge or for the purpose of aligning the canker hood after fitting. In order to remove the bottom of the cooker hood it is necessary to reseals the two fixing catches (1) located on the top front edge of the cooker hood. These must be pressed downwards and slightly forwards at the same time. The two catches (1) will now spring upwards, thereby reteaching the hood bottom (2).
After removing the hood bottom (2) release the self-clamping grille at one side and then remove it Fit a new filter mat and then replace the secularizing gristle (3). Refit the hood bottom (2). Air nitration The clean-air cartridge (air return unit only} will remain fully serviceable for approximately 18 months provided that the grease filter is cleaned and/or replaced at regular intervals, The clean-sit cartridge must then be renewed.
installation instructions If the ocker hood is to be used as an air-extraction unit, it must not be connected 1o a chimney or flue used for heating purposes. Tne cooking fumes may be dusted either upwards through a ventilation shaft or through an aperture in the outside wall, either fo the right, left or rear ot the conker hood. A straight connection pipe may be as long as ยง meters. if the pipe contains one right-angled bend, its length should not exceed 3 meters.
important! When fitting the pipe connection (7} it is necessary to remove the lid. This can be done only wither aid of a screwdriver or similar implement. Carefully insert the screwdriver between the housing and the lid at the point marked and give it a short twist in an anticlockwise direction to remove.
Removing the cooker hood bottom Release the two fixing catches (1) located on the top of the cooker hood, These must be pressed downwards and slightly forwards at the same time. The catches (1) will now spring upwards, thereby releasing the hood bottom. Pull the bosom forwards by about 10 mm and then withdraw it in a downwards direction (holding it firmly in both hands), Proceed in the reverse direction when refitting.
Remove the rubber plug (10). Fit the clean-air cartridge into the two recesses (11, 12} initiate fan housing. Secure by means of the plastic screw (13). Refit the cooker hood bottom (2).
Instructions for fixing the cover hood Fixing to wall 518 Wall hook 185 Mark the position of the cooker hood on the wall at the required height, The vertical distance between the gas or electric cooker hob and the bottom edge of the cooker hood must Place the drilling template against the wall and mark the holes for the wall hooks, The holes must be 618 mm apart (136 mm above the bottom edge of the cooker hood}. 3.
Fixing to wall cupboard 1 14 Remove the cooker hood bottom (2). This is done by releasing the two fixing catches (1) located on the top front edge of the cooker hood. These must be pressed downwards and slightly forwards at the same time, The two fixing catches (1) will now spring upwards, thereby releasing the hood bottom. Pull the bottom forwards by about 10 mm and then withdraw it in & downwards direction (holding i firmly in both hands), . Turn the wail cupboard upside down. .
What Necessary data 220V .. . the hood light does not light up. Check to make sure that the appliance is connected to the electricity supply and switched to the correct setting. Check the fuses in the fuse box In the case of all other faults it is absolutely necessary to Cali our Customer Service Department for assistance. Please state the following details when making your call: the Model Number ~ the E-Number = the F-Number.