Equipment Operation of fume extractor hood important! The appliance may only be The required operating mode {mayor running switched on when fully installed, Le. with and/or lighting) can be electroplated on the applied pipe section and outset grille contra pangs. The appliance then {return air operation] or with connected switched "On/Oft” by opening and closing exhaust air pipe system {exhaust air the furn protection panel operation}l Appliance description (Fig.
Technical data Fan outputs to DIN 44971 Setting Setting Setting “Min” “Max.” setting setting DEI630/DEA 830 {3 settings} exhaust air 135 190 265 return air 100 160 230 DEADBOLT 60/ {continuously variable} exhaust air 135 265 DEACON return air 100 230 *Exhaust air with 120 mm dia. pipe system; return air with KAFKA Original Carbon Sifter Accessories and fittings DE! 830/DEI 60/DEI 600 N 2 Side parts with mounting templates applied’) possessive sowers {for joining side parts 1o busing) 6 A 3.
Electrical installation Electrical connection (appliances with connected load below 3000 watts) Warning! All appliances with a 3 core lead must be earthed. Voltage and current Please ensure that the voltage and current indicated on the rating plate agree with the voltage of your electricity supply. 2207240 volts -~ (i.e. 2201240 V 2.
Electrical installation Arrangement of the protective contact plug socket directly above the furn extractor hood or above the overhead cabinet confers two advantages: 1. The plug socket is not visible, 2. You can easily DE-energize the appliance where necessary by unplugging it. For the necessary fixed connection, the fume extractor hood should be connected only by an electrical installer registered with the competent electricity supply company. Fascinating device is to be provided on the tied wiring side.
Prior to installation Preparation as exhaust air appliance theft kitchen fume is run out iro the open air through the external wall, you need telescopic wall box {special accessory, Fig. 4}. Order via AEG hare-sales service o dealership; wall box with supply and exhaust air duct. For dimensions and position of alr outlet openings: {Fig.
Prior to installation Preparation of furniture surround for exhaust air operation The design of DEI 630/DEI 60/DEI 600 N appliances enables the exhaust air has o be run backwards or to the side. After removal of the cover panel (Fig.
installation 9. The fume extractor hood is now to be competed depending on operating " Fit furniture front panel on fume protection pane {see page 28). mode: 12. insert fume protection pane! with Exhaust sir operation: strewed-on furniture front panel into Couple exhaust air system with exhaust appliance, ensuring that side parts of air connection-piece on appliance side fume protection panel are properly Refit cover panel. inserted in brake guide on RH and LH sides {Fig. 151).
Installation 4. Unscrew supplied complete taunting rai (see illustration on page 27/2 and 3) and screw together with appliance ceiling according 1o position relative to wail mounting angle (see Illustration on page 27/1). 5. Fit wall end panel as illustrated on page 2%/ Table ¥ so halt it remains adjustable for necessary height adjust extreme of appliance 6. For fitting of side parts on fixed or separate furniture side wall, see page 26 {installation between two cabinets}. 7.
Installation Fitting the furniture front panel on the fume protection panel Installation of DEt in furniture surround 1. Determine dimension between cabinet ceiling bottom edge) and door top edge {neighboring cabinet} and mark in supplied template (dimension “X7}. This dissension then corresponds to top edge of the furniture door. Place template centrality on rear of furniture front panel {Fig. 22} and mark out mounting holes. N.8.: Espadrille mounting holes! 2.
Operation of fume extractor hood Function description The individual numbers and symbols have the following meanings {(from right to left): Fig. 25 DEA 630/DEI 830 210 = Lighting “On/Off" O =Motor switched off 1 = Setting 1 2 insetting 3 insetting Fig.
Maintenance and care inserting/changing the grease filter {fleece) The grease filter with internal red stripes incorporated in the appliance is replaced bya new filter paper when the red stripes and/or the mark “Please change” with £-No. and F-No. visibly come through. The fitter shouts be changed every 2-3 months depending on use. ‘When repurchasing (special accessory), please note the special instructions for installation of the filter fleece and washable metal grease fighter in the retrofitting kit. 1.
Cleaning Important! To clean the fume extractor hood, DE-energize the appliance feign. pull out mains plug). Attest once per year, you should clean internal surfaces of your appliance free of grease deposits 1o ensure that its full reliability is retained. Old grease residues. are highly flammable. Supersaturated grease and deodorization filters are therefore also to be avoided. Special accessories Clean the external parts with & milf washing-liquid solution.