User’s Manual FAVORIT F89078VI-M 24” Stainless Steel Dishwasher User’s Manual
EN CONTENTS Contents 1 INTRODUCTION ....................................................................................................................... 5 2 SAFETY INFORMATION .......................................................................................................... 7 3 INSTALLATION MATERIAL....................................................................................................10 3.1 Kit supplied with dishwasher (models F65478VI-S / F89078VI-S) ........................
EN INTRODUCTION 1 INTRODUCTION Thank you for choosing one of our products. To install this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to installation of the appliance. The texts are easy to understand and are complete with detailed illustrations. This user-friendly manual will provide answers to all your questions about installation of the dishwasher.
EN INTRODUCTION Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. DANGER OF ELECTROCUTION. This symbol highlights information and warnings of an electrical nature which, if not observed, may compromise personal safety or damage the appliance. This symbol highlights general information and warnings. Tab. 1-01 6 Rev 0.
EN WARNINGS 2 SAFETY INFORMATION THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE AND MUST THEREFORE BE KEPT INTACT TOGETHER WITH THE MACHINE. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE DIRECTIVES CURRENTLY IN FORCE, INCLUDING THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE.
EN WARNINGS TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISHWASHER. DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS PACKAGING MATERIALS AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE. KEEP CHILDREN, PHYSICALLY AND/OR MENTALLY IMPAIRED ADULTS, AND ANIMALS AWAY FROM PACKAGING WASTE; DANGER OF SUFFOCATION. BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE MAINS POWER SUPPLY FROM THE WORK AREA.
EN WARNINGS DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING, WITH CONSEQUENT FIRE HAZARD. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS, ANIMALS OR PROPERTY RESULTING FROM FAILURE TO OBSERVE THE ABOVE PRECAUTIONS, FROM TAMPERING WITH EVEN A SINGLE COMPONENT OF THE APPLIANCE, OR FROM THE USE OF UNORIGINAL SPARE PARTS. IF IN DOUBT ABOUT THE CONTENTS OF THIS MANUAL, CONTACT THE TECHNICAL ASSISTANCE SERVICE. Rev 0.
EN INSTALLATION INSTRUCTIONS 3 INSTALLATION MATERIAL To install the dishwasher correctly, the following materials are required: • Phillips screwdriver (ref. A fig. 3-01); • spirit level (ref. B fig. 3-01); • tape measure (ref. C fig. 3-01); • compass saw (ref. D fig. 3-01); • pencil (ref. E fig. 3-01); • file (ref. F fig. 3-01); • 13 mm open-ended wrench (ref. G fig. 3-01); • plumbing pliers (ref. H fig. 3-01); • drill (ref. I fig. 3-01); • safety gloves (ref. L fig. 3-01). B A D C F E H G I L Fig.
EN INSTALLATION INSTRUCTIONS 3.1 Kit supplied with dishwasher (models F65478VI-S / F89078VI-S) The kit supplied with the dishwasher comprises: • adhesive steam guard (ref. A fig. 3-02); • 1 steel steam guard (ref. B fig. 3-02);* • 1 template for door panel (ref. C fig. 3-02); • 2 hooks for door panel (ref. D fig. 3-02); • 8 screws for securing the door panel hooks (ref. E fig. 3-02); • 2 screws for securing the door (ref. F fig. 3-02); • 2 screws for fixing the dishwasher to the adjacent walls (ref.
EN INSTALLATION INSTRUCTIONS 4 DIMENSIONS OF DISHWASHER (See fig. 4-01) Model F89078VI-M F89078VI-S F65478VI-S F45078I-M A (height) B (width) C (depth) 86 cm ÷ 91 cm 33-55/64” ÷ 35-55/64” 86 cm ÷ 91 cm 33-55/64” ÷ 35-55/64” 82 cm ÷ 87 cm 32-9/32” ÷ 34-1/4” 86 cm ÷ 91 cm 33-55/64” ÷ 35-55/64” 59.7 cm ÷ 59,9 cm 23-1/2” ÷ 23-37/64” 59.7 cm ÷ 59.9 cm 23-1/2” ÷ 23-37/64” 44.7 cm ÷ 44.9 cm 17-19/32” ÷ 17-43/64” 59.7 cm ÷ 59.
EN INSTALLATION INSTRUCTIONS 5 INSTALLATION AND HOOK-UP DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE APPLIANCE. Remove the polystyrene rack blocks. Position the appliance in the chosen installation position. The sides and rear of the appliance can lie against kitchen units or walls. If the dishwasher is installed next to a heat source, separate it with a heat insulating panel in order to prevent overheating and malfunctions.
EN INSTALLATION INSTRUCTIONS 5.1 Leveling 5.1.1 Mounting the feet (only for some models) Turn the appliance upside-down (see fig. 5-01). Tighten the nut (see ref. A fig. 5-01) onto the threaded pin (see ref. B fig. 5-01) of the foot and then fit the supplied washer; do this on both feet. Screw the feet onto the appliance until the washers touch the base; the two feet must be manually adjusted to the same height to prevent excessive differences in height between one foot and the other.
EN INSTALLATION INSTRUCTIONS 5.1.2 Levelling the appliance Level the appliance using the relative adjustable feet (e.g.: ref. A fig. 5-02); use an open-ended wrench to rotate the feet until the dishwasher is perfectly level. Some models are fitted with just one rear foot which can be adjusted with a screw located at the bottom front of the appliance (ref. A fig. 5-03); use a suitable Phillips screwdriver to turn the screw until the dishwasher is perfectly level.
EN INSTALLATION INSTRUCTIONS A Fig. 5-03 5.2 Connections Install the dishwasher so as to allow ease of access to the electrical and hydraulic connections through the adjacent unit. These connections must never be behind the dishwasher. The inlet and drain hoses can be pointed in all directions. make sure that they are not bent, crushed or too tight. Tighten the ring nut after pointing the hoses in the required direction.
EN INSTALLATION INSTRUCTIONS A through hole with a diameter of at least 8 cm (5/32”) is required to pass the hoses and power cord (ref. A fig. 5-05). Make sure there area no rough edges that could damage the power cord or hoses. If the dishwasher is installed in a metal unit protect the edge of the through hole for the hoses and power cord with a gasket. Do not use extension cords when making the electrical connection as these do not guarantee safety.
EN INSTALLATION INSTRUCTIONS 5.2.1.1 Connecting to the water tap Connect the inlet hose to a threaded ¾” gas cold water tap, fitting the supplied filter (ref. A fig. 5-06). Firmly secure the hose by tightening the relative ring nut with your hands (ref. B fig. 5-06); finish by tightening another ¼ turn using a pair of plumbing pliers. For models fitted with ACQUASTOP (ref. C fig. 5-06) the filter is already present in the threaded ring nut.
EN INSTALLATION INSTRUCTIONS Do not cut the inlet hose (see fig. 5-07). If the hose is cut, the dishwasher will not work, water will leak and you may be injured. If the hose is too long, wind it up tidily and place it behind the appliance. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses. Fig. 5-07 When connecting the dishwasher drain hose to the sink make sure that the hose is not bent (ref. A fig.
EN INSTALLATION INSTRUCTIONS 5.2.1.2 Connecting the drain hose Connecting to a drain Insert the relative hose into a drain with a minimum diameter of 4 cm (1-37/64”) (ref. A fig. 5-09); alternatively, place the hose on the sink (ref. B fig. 5-09) using the supplied hose support (see fig. 5-10), but taking care to avoid obstructions or excessive curving. Make sure the hose cannot fall out. For this purpose, the hose support is fitted with a hole (ref. A fig.
EN INSTALLATION INSTRUCTIONS Connecting to a “T” union of the drain circuit MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Connect the dishwasher drain hose (ref. A fig. 5-11) to the “T” union (ref. B fig. 5-11) of the drain circuit using a 38 to 50 mm (1-1/2 to 2”) screw clamp* (ref. C fig. 5-11); if necessary, cut the end of the dishwasher drain hose (ref. D fig.
EN INSTALLATION INSTRUCTIONS Connecting to a waste disposal unit with an air gap MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Remove the cover of the waste disposal unit (ref. A fig. 5-12). 2. Connect the dishwasher drain hose (ref. B fig. 5-12) to the air gap (ref. C fig. 5-12) using the wide spring clamp (ref. D fig. 5-12); if necessary, cut the end of the dishwasher drain hose (ref. E fig.
EN INSTALLATION INSTRUCTIONS Connecting to the air gap (no waste disposal unit) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Connect the dishwasher drain hose (ref. A fig. 5-13) to the air gap (ref. B fig. 5-13) using the wide spring clamp (ref. C fig. 5-13); if necessary, cut the end of the dishwasher drain hose (ref. D fig. 5-13) (do not cut the corrugated section).
EN INSTALLATION INSTRUCTIONS Connecting to a waste disposal unit (no air gap) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Remove the cover of the waste disposal unit (ref. A fig. 5-14). 2. Connect the dishwasher drain hose (ref. B fig. 5-14) to the waste disposal unit inlet (ref. C fig. 5-14), using the wide spring clamp (ref. D fig. 5-14). A D C B Fig. 5-14 24 Rev 0.
EN INSTALLATION INSTRUCTIONS 5.2.2 Electrical connections and warnings CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE. THIS APPLIANCE MUST BE GROUNDED.
EN INSTALLATION INSTRUCTIONS The plug at the end of the power cord and the corresponding socket must be of the same type and must conform to current regulations governing electrical appliances. The plug must be accessible after installation. Never remove the plug by pulling on the wire. If the power cord is damaged, have it replaced by the manufacturer or an authorized service centre.
EN INSTALLATION INSTRUCTIONS Fig. 5-16 Fig. 5-17 Push the dishwasher into position, taking care not to twist or crush the power cord or hoses (see fig. 5-18). TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO PUSH THE DISHWASHER INTO PLACE. Fig. 5-18 Rev 0.
EN INSTALLATION INSTRUCTIONS 5.3.2 Procedure for mounting the door panel Mount the door panel. Place the template on the inner surface of the panel, centering it along the upper side and matching up the reference locators (ref. A fig. 5-19); mark the position of the door hooks with a pencil (see fig. 5-19). Remove the template and use a drill with a suitable bit to make holes at the points marked on the panel. A A Fig.
EN INSTALLATION INSTRUCTIONS Drill holes for the panel handle using a drill with a suitable bit. Use the screwdriver to secure the door handle before hooking the panel to the dishwasher (see fig. 5-21). N.B.: the screws are not supplied. Fig. 5-21 Insert the door spacers contained in the accessory bag (see fig. 5-22). 2 x (s x-dx) Fig. 5-22 Rev 0.
EN INSTALLATION INSTRUCTIONS Attach the door panel: fit the hooks into their slots on the dishwasher and allow the panel to slide downwards and slip in to place (see fig. 5-23). 1 2 Fig. 5-23 Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm (25/32”) (see fig. 5-24). Fig. 5-24 30 Rev 0.
EN INSTALLATION INSTRUCTIONS Make sure the dishwasher door, complete with panel, opens comfortably and that the base plate (ref. A fig. 5-25) does not prevent it from opening fully. If the base plate prevents the door from opening, mark out the section to remove (see fig. 5-25), take out the base plate and cut it along the marking using a compass saw (see fig. 5-26). 600 mm (2 450 mm 3-53/64") (23/32 ") A Fig. 5-25 Fig. 5-26 Rev 0.
EN INSTALLATION INSTRUCTIONS 5.3.3 Completion of installation Finish the cut with a file (see fig. 5-27) in order to remove any burrs and/or imperfections. Put back the base plate (see fig. 5-28) and try to open the dishwasher door fully; if the base plate still obstructs the door, repeat the above operations. Fig. 5-27 Fig. 5-28 32 Rev 0.
EN INSTALLATION INSTRUCTIONS Before securing the dishwasher to the adjacent units, attach the gaskets to the sides. Remove the adhesive band on the gasket (see fig. 5-29). Fig. 5-29 Fix the gasket to the dishwasher, inserting it in the seat on the sides towards the front (see fig. 5-30), and making sure that the long side of the gasket, the one with the hole for inserting the screw, is attached to the outside of the dishwasher; the hole in the long side must match the hole in the dishwasher (see ref.
EN INSTALLATION INSTRUCTIONS A Fig. 5-31 Fig. 5-32 shows the state of the dishwasher after the above operations are performed. Fig. 5-32 34 Rev 0.
EN INSTALLATION INSTRUCTIONS Tighten the supplied screws with a screwdriver; this operation definitively fixes the dishwasher to the adjacent units; cover the side holes using the supplied plugs (ref. A fig. 5-33). A Fig. 5-33 5.4 Testing After installation, test the dishwasher by starting a work cycle. Check for leaks and make sure the appliance does not malfunction. Rev 0.
Q- Warranty AEG products are designed and built to the highest standards. We expect your appliances to provide many years of trouble free enjoyment. In the event of an appliance requiring attention, each appliance is covered by a 2 year warranty from the date of purchase. Refer to warranty policy for complete terms and conditions. Coverage is for costs of parts and labor for appliances in capital cities & metropolitan areas.
AEG appliances are imported and distributed in North America by Euro-Line Appliances Inc. For more information visit www.euro-line-appliances.com / www.elawest.com 871 Cranberry Court Oakville, ON L6L 6J7 Canada Toll Free: 1.800.421.6332 Showroom: 905.829.3980 marketing@euro-line-appliances.com 2912 West 4th Ave Vancouver, BC V6K 1R2 Canada Toll Free: 1.855.352-9378 Showroom: 604.235.3980 info@elawest.