32 Contents 1 Introduction 1I Technical data 1l General For the electrician Optional extras compartmentalizes on ducting {extraction system) Preparing the cooker hood for the extraction of air Preparing the cooker hood for the reconciliation of alr IV Assembly and installation Installation dimensions Installation of the filminess cooker hood Fitting the decor front panel V Operation VI Maintenance Replacing the grease filter Replacing the lamps Vil In case of problems I Introduction These instructions are d
1l Technical data Dimensions: width/heightidepth 598 x 170 x 300 Connection: 220V via fixed power cable with SCHUSS plug (permanent connections may be effective by a qualified electrician only). Total connected load: 215W Weight' 7.5kg approx. Radial fan: 95W Appliance reference: fan stages: 3 an capacity: extraction of air: 188 m3/h 340 ma/n re circulation of air: 150 m3/h ~ 240 Mb Appliance reference: fan stages.
it General Optional extras As an internationalize front panel available from the manufacturer of your Kitchen furniture. your specialist dealer can offer You decor panel as an optional extra. ) for dusted installation (extraction system) To direct the cooking vapors ¢ through an outside wall into the: atmosphere you require a telescopic wall box from our range of accessories, (A schematic diagram of this useful accessory is shown in fig. 13.
important notes on ducting (extraction system) With a dusted installation the waste air passes up through a ventilating shaft or through the outer wall directly into the atmosphere. Clothesline cooker hood featuresanairoutiet at the mandatory the back. Tocantins the cooker toadstool ventilating shaft we recommend the highly flexible, difficult to it air-extraction hose from arrange of accessories. Your specialist dealer semis this hose material by the yard.
M General Fitting the activated charcoal fighter &) Using a screw driver, remove the plastic dummies fig. 11/3. b Take the activated charlatan filter from its box, Crass the filler entitlement direction of the arrow from the retaining frame unit it engages units limit position. See fig. 12/1 ¢} Insert the prepared filter with the two retaining hooks in the sockets at the casing — fig. 11 Push the filter against the casing and secure with the two spit ping by inserting the min the ex panders. See fig. 11.
Note! We recommend the removal of the lower filter frame prior to the installation, in this way you avoid possible damage to the filter frame. Removal: See page 19, Removal of the lower filter frame ~steps and 2, Seo also figs. 22 and 23, ‘Her incorporating the sliminess cooker hood in a wall cupboard with extended side walls, iris necessary lo unscrew the plastic end pieces of the appliance. Fig. 14/1 Next, remove the 4 springs. Fig. 15. For says removal give them a 45 wrn with & suitable screwdriver.
V Operation ‘The slimline cooker hood should besmirched on not after than the ‘stair of the cooking process. The built-in grease and activated charcoal filters increase their efficiency it the mistiness cooker hood isnotswiiched off immediately on completion of the cooking process, but 20-30 minutes later.
How to remove the upper fighter frame (shindig the front panel). 1. Extend front panel fully (fig. 25). Using the forefingers, push the twa springs first up and then to remove thee from their sockets. Remove the filter frame and hold the grease filter fissile in place {fig, 26). Thoroughly clean the grease filter frame in hot washing-up water and wipe dry. Position the new grease fighter fleece in the frame with the colored strips facing inward. There is no holding-down wire for this filter mat.
Vil In case of problems Please contact our Technical Service in case ot queries or difficulties. {See the enclosed list of technical service crescent. ‘When contacting us please quote: 1 = the made) number 2 = the E number 3 = the ¥ number This data will be found on the nameplate and on the title page of these instructions. We reserve the right to alter the design of our products as part of our technical development work.