Electric Built-In Hob Units Installation and Operating Instructions ME 4.48 R, EM 4,58 D, EME 4.58 D, EME 4.77 D, LEMUEL 4.77 p.
Your AEG Hob Unit will last for years, providing you follow the directions in this booklet, they are extremely important for the correct use of the hob unit. IMPORTANT: This equipment is designed specifically for domestic purposes and the manufactures cannot accept responsibility if used in any other type of installation, Alf electrical installations must be carried out by a -patent electrical contractor, to EE wiring 1. regulations.
A.FOR THE INSTALLER Installation of the hob unit To install the hob unit a cut out in the work fop has to be provided according to the sketches indicated below. The built-in hob unit must fit in the aperture so that the automatic plates or the quick action cooker plates are positioned in the front. No support drips should remain underneath the cut out in the work top: these should be sawed back to come in ne with the edges of the paperer.
approx. Min. |2 Fig. 3 EME 477 D » wut out in work top the extension piece of the ! d or cupboard ! unit or the control panel is partition board of cup situated on the right, this width can be reduced 10 25 minimum, Fig. 4 Minimum distances to surrounding walls.
Fig. 5 LEMUEL 4.77 in case a cupboard with a top is to be fitted underneath the work top {or & stove for that matter) an additional cut out has to be provided o cover the area of the cooker plates. permissible | size | Furthermore, it must be ensued that no inflammable objects or articles which catch fire easily or which are deformation, are placed directly below the cooker plates. Fig. & Positioning of the cooker plates in relation to a cupboard or stove to be tutted underneath the unit.
The enclosed durable, elastic sa that only & small overlap and heat-resistant seal strips remains towards _the contact to be laid into the hob edge surface (see fig. 7). Fig. 7 approx.
Be fora placing the hob unit in the quark top the screws of the clamping strip have to.be unscrewed fig. 8 a and & b). Afterwards the hob has to be stewed into the work top clamping strap Fig. and 85 Please make sure that ihe work surface and also the hot unit are mounted level. Only then, for instance, wilt you' get equal distribution of Description of circuit connection for hob and stove, control panel respectively.
Final Adjustment of the Cover Pl ales If not already the case, the cooker plates can be made level by finally adjusting them with the adjusting screws which can be reached from underneath {fig. 9} Fig. 9 Connection of two bully-in hob unites 1 All to give protection from the top 2 All to supper the joint from below 3 Screw off 4 Seal Fig. 10 The built-in hob units should be placed in tha aperture side by side. The rat 1 and the seal 4 should be placed between the gabs from the top as indicated in fig, 10.
The Connection IMPORTANT: SEE FOOTNOTE ON PAGE 3 AEG electric builtin appliances conform 1o safely refutations laid out by VDE {*Association of German According fo these heat emission can be as high as 60° plus room temperature. Should any damages occur, please consult the dealer from whom you have obtained the appliance, or your AEG Service Agent. After screws 1, 2 and 3 have been unenlightened, the rope of the installation case can be tilted up.
8.
Selection of Pots You can use al pots Respective of the material, provided they have a love smooth bottom, Most suitable, of course, are spacial electric pots with & pain level ground bottom, The size of the pots should comply with the Size of the plates. It is most economical it the diameter of the pats is =, 3, approximately 2 om larger than that of the plate. In any case the diameter of the pot should not be smaller than that of the plate.
1 = Knob for cooker plate left front = Knob for cooker plate right front 3 = Nab for cooker plate theft rear The Automatic Clock Eig. 16 and 17 4 = Knob for cooker plate right rear 5 = control tamp ~ tallow 8= Start button — 10 operate push and furn Regulating button for; a) short time alarm clock and cooking time duration — turn b} time ~ wind up and term = Transfer switch ) automatic operation @ E b} short dime alarm clock a E Window and deaf plate for short time alarm clock, i ©.
1. Turn the knob of the 18 of 14,5 cm automatic piste 10 the required temperature. 2. Switch on the automate clock 1 automatic starting ot switching off s required. 2.1 Turn the transfer switch with ring handle &, &) o symbol, in window E, you will then see @ B 22 Regulating Example A1 8,00 am a meal is being put on the 18 or 14,8 em automatic plate which should be ready by 13.00 pm. The meal takes 1 hour o be ready.
5.2 Short time alarm clock You turn regulating knob B unit the desired number appears in window E. The time lapse starts immediately. The signal swi teas itself off auto ma call after approx. 10 minutes, unless you switch the dial plate on to symbol. a 5.4 Correcting of wrongly set times: Adjusting is possible at any dime by turning regulating knob B dither way. 5.4 During an automatic oo~ king process the spare automatic cooker plate stays socked and cannot be operated manually.
Operation of thé automatic cooking-plate higher figure means — higher warming up temperature . e warming bl small quantities swelling -\ target quantities — uneven bases oW i 55w median baking frying stewing steaming cooking exact regulation depends on the pot and on the quantity of the content. The following information shoulder treated as & general guide from the sari please adjust to the corresponding figure in the desired zone...