EN User Manual Dishwasher F34300VI0
www.aeg.com CONTENTS 1. SAFETY INFORMATION.................................................................................................3 2. SAFETY INSTRUCTIONS................................................................................................ 4 3. PRODUCT DESCRIPTION.............................................................................................. 6 4. CONTROL PANEL...........................................................................................................6 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH 5 • The appliance can release hot steam if you open the door while a programme operates. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. 2.5 Service A B • The water inlet hose has an external transparent sheath. If the hose is damaged, the water in the hose becomes dark. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 8 7 6 5 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 7 8 9 10 11 4 3 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket 4.
ENGLISH 7 4.1 Indicators Indicator Description Running programme indicator. It comes on when the programme starts and goes off when the programme is completed. End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates. 5.
www.aeg.com 6. SETTINGS 6.1 Programme selection mode and user mode However, if this does not happen, you can set the programme selection mode in the following way: When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode. Press and hold the programme button until the appliance is in programme selection mode. In user mode, the following settings can be changed: • The level of the water softener according to the water hardness.
ENGLISH than 21°dH, you can set the lowest water softener level. It deactivates the salt refill indicator. If you use standard detergent or multitablets without salt, set the proper water hardness level to keep the salt refill indicator active. How to set the water softener level The appliance must be in programme selection mode. 1. To enter the user mode, press and hold the programme button until the indicator starts to flash and the indicator on with fixed light. 2.
www.aeg.com 7.1 The salt container CAUTION! Only use salt specifically designed for dishwashers. 7.2 How to fill the rinse aid dispenser A D B The salt is used to recharge the resin in the water softener and to assure good washing results in the daily use. How to fill the salt container 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (Only for the first time). 3. Fill the salt container with dishwasher salt.
ENGLISH Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 8.1 Using the detergent D A B 30 20 30 B 1. Adjust the water softener to the lowest level. 2. Set the rinse aid dispenser to the lowest position. 8.
www.aeg.com Cancelling the programme Press and hold the programme button until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme. 1. Press the on/off button to deactivate the appliance. 2. Close the water tap. If you do not deactivate the appliance within 5 minutes all indicators goes off. This helps to decrease energy consumption. End of the programme When the programme is completed the indicator is on. 9.
ENGLISH 9.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5.
www.aeg.com C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 4. Wash the filters.
ENGLISH 10.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 10.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 15 • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance.
www.aeg.com Problem and alarm code Possible cause and solution The appliance does not fill with water. • Make sure that the water tap is open. • The end indicator flashes 1 time in- • Make sure that the pressure of the water suptermittently. ply is not too low. For this information, contact • Acoustic signal sounds 1 time inyour local water authority. termittently. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged.
ENGLISH Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If 17 the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 11.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
www.aeg.com Problem Possible cause and solution Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
ENGLISH 19 13. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances * marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
100014390-A-322015 www.aeg.