ÖKO_FAVORIT 40300 Dishwasher User Instructions
Dear customer, Please read these user instructions carefully. Above all please observe the safety instructions on the first few pages ofthese user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance. 1 0 The warning triangle and/or specific words (Warning!, Caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance.
Contents CONTENTS Operating Instructions .................................... 5 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Economical and Ecological Dishwashing . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Appliance Features and Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Installation and Connection Instructions . . . . . . . . . . . . . . . . 29 Installing the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Free-Standing Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Connecting the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions OPERATING INSTRUCTIONS 1 Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you aware of the following safety information: Installation, Connection and Placing into Operation • The dishwasher may only be transported upright. • Check the dishwasher for transport damage.
Operating Instructions General Safety • Repairs to the dishwasher are only to be carried out by qualified service engineers. Improper repairs can give rise to significant hazards for the user. If your appliance needs repairing, please contact customer service or your dealer. • Never place the dishwasher in operation if the mains cable, water inlet or drain hose is damaged; or the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible.
Operating Instructions • Do not sit or stand on the open door, the appliance may tip over. • In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently wired to the mains: switch off the fuse(s) or unscrew them. 2 Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled.
Operating Instructions Appliance Features and Control Panel Rubber Seal for Connecting the Water Feed to the Upper Spray Arm Spray Arms Water Hardness Switch Container for Special Salt Container for Rinse Aid Container for Detergent Rating Plate 8 Filters
Operating Instructions Control Panel Power Indicator Light Programme Selector SALT Indicator Door Handle Programme Switch Set the point at which the wash programme is to start using the programme switch. The programme switch rotates during the wash programme and indicates the position that has been reached in the programme. Switch on the dishwasher and start a wash programme using the programme selector.
Operating Instructions Adjusting the Water Softener To prevent the build up of scale on dishes and in the dishwasher, the dishes must be washed with soft, i.e. low lime content water. For this reason the dishwasher is fitted with a water softener in which tap water from a hardness of 4 °d (German degrees) is softened with the aid of special salt. 3 Your local water authority can advise you on the hardness of the water in your area. The water softener has 4 settings.
Operating Instructions Filling with Special Salt for the Water Softener 1 Use only special salt for dishwashers. Never fill the salt container with any another type of salt (e.g. culinary salt) or dishwasher detergent. This would irreparably damage the water softener. Prior to filling with salt, please check each time that you really do have a packet of special salt in your hand.
Operating Instructions Filling with Rinse Aid Rinse aid ensures that your dishes gleam and are free from spots, and that you glasses are clear. 1 Use only branded rinse aid for dishwashers. Never fill the rinse aid container with any another substance (e.g. concentrated vinegar). This would damage the appliance. Fill with rinse aid: – Prior to using the dishwasher for the first time – When a dark point surrounded by a light ring is to be seen in the indicator window on the container.
Operating Instructions ,Adjusting 3 Rinse Aid Dosing As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6. Only change the setting if streaks, milky spots or dried on water marks are visible on glasses or crockery. 0 1. Open the door of the dishwasher. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid. 4. Set the dose level. 5.
Operating Instructions In Daily Use • Is it necessary to refill with special salt or rinse aid? • Load cutlery and dishes into the dishwasher • Fill with dishwasher detergent • Select a wash programme suitable for the cutlery and dishes • Start the wash programme Loading cutlery and dishes 1 Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher.
Operating Instructions – To avoid damage to glasses, they must not touch – Do not lay small objects (e.g. lids) in the cutlery rack Loading Cutlery Long, pointed items of cutlery in the cutlery rack are a hazard, particularly to children (see Safety Instructions). They should therefore be placed in the upper rack. To ensure that all items of cutlery are completely washed, you should 1. Place the grid insert on the cutlery rack 2.
Operating Instructions Loading Pans, Frying Pans and Large Plates Load large and heavily soiled dishes in the lower rack. To ease the loading of large items at some dishwasher-models the two rows of prongs for the right-hand plate insert can be folded down: 0 1. Slightly lift the right plate insert. 3 2. Fold the plate insert to the left.
Operating Instructions Loading Cups, Glasses and Coffee Services Load small, delicate items and long pointed cutlery in the upper rack. • Arrange items of crockery on the folding cups racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall items. • Lay or hang wine, champagne, and brandy glasses in the cut outs on the cup racks. • Glasses, beakers, etc. can also be placed on the two rows of prongs on the left of the upper rack.
Operating Instructions Filling with Detergent 1 Only use dishwasher detergent. Fill with detergent: – Prior to the start of a wash programme (not for the pre wash programme). The detergent is released into the wash water during the programme. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. The detergent compartment is on the inside of the dishwasher door. 0 1. If the lid is closed: press release button (1). The lid springs open. 2 2.
Operating Instructions Bio Wash Programmes and Concentrated Detergents Based on their chemical composition, dishwasher detergents can be split into two basic types: – Conventional, alkaline detergents with caustic components – Weak alkaline concentrated detergents with natural enzymes.
Operating Instructions Selecting the Wash Programme (Programme Table) Choose the most suitable wash programme with the aid of this table: Type of Dishes Dinner Service and Cooking Utensils In Addition Type of Soiling • heavily soiled • dried leftovers with non-temperature resistant dishes • normally soiled Dessert Dishes and Coffee Service All Dish Types with delicate glasses - • lightly soiled particularly suited to the use of concentrated detergents. ò ò ò ò NORMAL NORMAL BIO ECON.
Operating Instructions Starting the Wash Programme 0 1. Check that the dishes and cutlery are loaded into the dishwasher in such a manner that the spray arms are free to rotate. 2. Open the tap fully. 3. Close dishwasher door. 4. Turn the programme switch clockwise to A, or B or C (see „ Programme Table“). For interference suppression reasons, only operate the programme switch with the dishwasher switched off. It is also possible that the automated addition of detergent will be triggered. 5.
Operating Instructions Interrupting the wash programme by opening the door of the dishwasher Hot steam can escape when the door is opened. There is a risk of scolding! Open the door carefully. 0 1. Open the door of the dishwasher. The wash programme stops. 2. Shut the door. The wash programme continues. 1 Switching Off the Dishwasher When the wash programme is finished: 0 1. Turn the programme selector to the I position. Power indicator light goes out.
Operating Instructions Care and Cleaning 1 Do not under any circumstances use furniture care products or aggressive cleaners. • If necessary, clean the controls only with a soft cloth and pure warm water. • The spray arms do not need cleaning. • Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary. Cleaning the Filter The filters in the base of the washing compartment are to a large extent self-cleaning.
Operating Instructions 7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. 1 Under no circumstances may the dishwasher be used without filters. What to do, when ...
Operating Instructions ...there are problems with the operation of the dishwasher. Malfunction Possible Cause The drain pump in the dishwasher runs conThe anti-flood system has tinuously - even with been triggered. the appliance switched off. Remedy Close the tap, then unplug from the mains and contact customer service. The door of the dishwasher is Shut the door. not closed properly. Mains plug is not plugged in. Insert mains plug. House fuse in defective. Replace fuse.
Operating Instructions – The filter in the base of the washing compartment is dirty or incorrectly positioned. – Detergent was not used or too little was used. – In the case of scale deposits on the dishes: the special salt container is empty or the water softener is incorrectly adjusted. – The drain hose is incorrectly laid. The dishes are wet and dull. – Rinse aid was not used. – The rinse aid container is empty. There are streaks, milky spots or a bluish coating on glasses and dishes.
Operating Instructions Technical Data Capacity: 12 place settings including serving dishes Permitted Water Pressure: 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Electrical Connection: Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right. Dishwasher: Free-Standing Appliances Dimensions: 850 x 600 x 600 (H x W x D in mm) Max.
Operating Instructions Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table). Full Load: 12 place settings incl. serving dishes Half Load: 6 place settings incl.
Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrewing: – use a screwdriver. • The drain hose, inlet hose and mains cable must not be kinked or crushed when the dishwasher is in position.
Installation and Connection Instructions • If the dishwasher is installed underneath a kitchen work surface, the original work surface of the dishwasher is to be removed as follows: – Unscrew the screws (1) from the elbows on the back side. – Slide the work surface approx. 1cm to the rear (3) , lift at the front (4) and remove. – Press the work surface retaining brackets at the position shown in the diagram (4) and remove the bracket at an angle to the rear (5).
Installation and Connection Instructions Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations. • The dishwasher can be connected to cold and hot water supplies up to max. 60 °C. • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.
Installation and Connection Instructions Water drain Drain hose 1 The drain hose must not be kinked, crushed or entangled. • Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height 30 cm above the lower edge of the machine. Extension hoses • Extension hoses are available from your dealer or customer service. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded.
Installation and Connection Instructions Leak Prevention System For protection from damage due to water leaks, the dishwasher is equipped with a leak prevention system, the AQUA CONTROL SYSTEM. In the event of a fault, the safety valve immediately interrupts the supply of water to the appliance and the drain pump switches on. By this means water can neither escape nor overflow. The remaining water in the appliance is automatically pumped out.
Installation and Connection Instructions Connections The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance. The plumbing and electrical installation example given below can only be regarded as a recommendation; the actual situation where the dishwasher is to be installed will define the exact installation (available connections, local electricity and water board regulations for connecting up appliances, etc.).
Service Departments SERVICE DEPARTMENTS South Africa AEG Domestic Appliances Head Office 55, 12th Road, Kew P.O. Box 3657 JOHANNESBURG 2000 Tel.: elfa(011) 806-9111 Telefax: (011) 887-0849 DURBAN 84 & 73 Victoria Park 123 Old North Coast Road Glen Anil P.O. Box 1061 DURBAN 4999 Tel.: elef(031) 569-1470 Telefax: (931) 569-1498 CAPE TOWN 43 Neptune Street Paarden Eiland P.O Box 184 PAARDEN EILAND 7420 Tel.: elef(021) 511-0486 Telefax: (021) 510-5073 PORT ELISABETH 43 Pickering Street Newton Park P.O.
Guarantee Conditions GUARANTEE CONDITIONS Guarantee Conditions 1. AEG guarantees the equipment against defective material or faulty manufacture, provided it is used for domestic purposes only, for a period twelve (12) months from the date of purchase by the original purchaser. If used for commercial purposes, the warrantly period will be limited to six (6) months. 2.
Service SERVICE In the section "What to do, if..." the most important sources of faults that you can rectify yourself are summarised. If, nevertheless, you call in customer service to resolve a problem listed in these instruction, or because of an error made in operating the appliance, the customer service engineer’s visit is not free of charge, even during the warranty period. If you can not find any information on a specific malfunction in these operating instructions, please contact customer service.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.