NL FR DE Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle Benutzerinformation Geschirrspüler 2 22 43 FAVORIT55311VI0
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 3 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 6 5. PROGRAMMA’S..................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen onder druk en/of stoom om het apparaat te reinigen.
NEDERLANDS ampère. Als de zekering van de stekker verwisseld moet worden, gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet. • Indien buizen lang niet zijn gebruikt, er reparaties hebben plaatsgevonden of er nieuwe apparaten zijn geplaatst (watermeters, enz.), moet u, voordat de nieuwe buizen worden aangesloten, het water laten stromen tot het schoon en helder is.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 1 2 11 10 1 2 3 4 5 6 9 8 7 6 Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 5 7 8 9 10 11 4 3 Glansmiddeldoseerbakje Afwasmiddeldoseerbakje Bestekkorf Onderkorf Bovenkorf 4.
NEDERLANDS 7 4.1 Indicatielampjes Aanduiding Beschrijving XtraDry-indicatielampje. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. 5.
www.aeg.com 5.1 Verbruiksgegevens Programma 1) Water (l) Energie(kWh) Programmaduur (min) 11 1.050 195 7 - 12 0.6 - 1.4 40 - 150 13 - 15 1.5 - 1.6 150 - 170 9 0.8 30 4 0.1 14 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
NEDERLANDS 9 belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten. Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.
www.aeg.com Schakel de aanduiding in om de glansmiddelindicator actief te houden als u standaard wasmiddel of multitabletten zonder glansmiddel bevat. Het uitschakelen van de melding van een leeg glansmiddeldoseerbakje 1. Om de gebruikersmodus in te voeren, drukt u tegelijkertijd totdat de lampjes en gaan knipperen en het display leeg is. 2. Druk op , Het apparaat moet in de programmakeuzemodus staan. 1. Om de gebruikersmodus in te voeren, drukt u tegelijkertijd en .
NEDERLANDS 7.1 XtraDry Activeer deze optie als u het droogresultaat een boost wilt geven. Bij het gebruik van deze optie kunnen de duur van sommige programma´s, het waterverbruik en de temperatuur van de laatste spoeling worden beïnvloed. 11 Als de optie niet van toepassing is op het programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit. Het display geeft de bijgewerkte programmaduur weer.
www.aeg.com Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Gevaar voor roest. Start om dit te voorkomen een programma nadat u het zoutreservoir heeft bijgevuld. 8.2 Het vullen van het glansmiddeldoseerbakje A D B C B A M AX 4 1 3 2 + - C D 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de programmakeuzemodus staat. • Vul het zoutreservoir als het zoutindicatielampje brandt.
NEDERLANDS 9.1 Vaatwasmiddel gebruiken 30 20 C 30 B Een programma starten 1. Laat de deur op een kier staan. 2. Druk op de aan/uit-toets om het apparaat te activeren. Zorg dat het apparaat in de keuzemodus Programma staat. 3. Druk op de toets van het desbetreffende programma dat u wilt starten. Het display geeft de programmaduur weer. 4. Stel de bruikbare opties in. 5. Sluit de deur van de afwasmachine om het programma te starten. D A B A 13 D Een programma starten met een uitgestelde start 1.
www.aeg.com De uitgestelde start annuleren tijdens het aftellen Als u de uitgestelde start annuleert, moet u het programma en de opties opnieuw instellen. Houd tegelijkertijd en ingedrukt tot het apparaat in de programmakeuzemodus staat. Het programma annuleren Houd tegelijkertijd en ingedrukt tot het apparaat in de programmakeuzemodus staat. Controleer of er vaatwasmiddel in het vaatwasmiddelbakje aanwezig is voordat u een nieuw programma start.
NEDERLANDS 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4. Als het programma is voltooid, wijzigt u de waterontharder in de waterhardheid van uw omgeving. 5.
www.aeg.com 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter terug (A). Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
NEDERLANDS LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat wordt niet gevuld met water. Op het display verschijnt • Controleer of de waterkraan is geopend. • Zorg dat de waterdruk niet te laag is. Neem hiervoor zo nodig contact op met uw lokale waterleidingbedrijf. • Controleer of de waterkraan niet verstopt is. • Controleer of het filter in de toevoerslang niet verstopt is. • Controleer of er geen knikken of bochten in de watertoevoerslang aanwezig zijn. .
NEDERLANDS Raadpleeg "Voor het eerste gebruik", "Dagelijks gebruik", of "Aanwijzingen en tips" voor andere mogelijke oorzaken. 19 neemt u contact op met onze klantenservice. Voor alarmcodes die niet in de tabel vermeld zijn, neemt u contact op met de service-afdeling. Schakel het apparaat na controle aan en uit. Als het probleem opnieuw optreedt, 12.1 De was- en droogresultaten zijn niet naar tevredenheid Probleem Mogelijke oorzaak en oplossing Slechte wasresultaten.
www.aeg.com Probleem Mogelijke oorzaak en oplossing De binnenkant van het apparaat is nat. • Dit is geen fout van het apparaat. Het wordt veroorzaakt door de vochtigheid in de lucht die tegen de wanden condenseert. Opvallend veel schuim tijdens het wassen. • Gebruik alleen wasmiddel voor afwasautomaten. • Het glansmiddeldoseerbakje is lek. Neem contact op met een servicecentrum. Roestresten op bestek. • Er wordt voor het wassen teveel zout in het water gebruikt.
NEDERLANDS Watertoevoerdruk Min. / max. bar (MPa) Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 13 Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.10 21 0.5 (0.05) / 8 (0.8) 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door alternatieve, milieuvriendelijkere energiebronnen geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14.
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................22 2. CONSIGNES DE SÉCURITÉ......................................................................................24 3. DESCRIPTION DE L'APPAREIL.................................................................................26 4. BANDEAU DE COMMANDE....................................................................................26 5. PROGRAMMES....................
FRANÇAIS 23 pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute. Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur. Ne pulvérisez pas d'eau ni de vapeur à haute pression pour nettoyer l'appareil.
FRANÇAIS • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire. • Pendant et après la première utilisation de l'appareil, vérifiez qu'aucune fuite n'est visible. • Le tuyau d'arrivée d'eau comporte une vanne de sécurité et une gaine avec un câble d'alimentation intérieur.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 11 10 1 2 3 4 5 6 9 8 7 6 Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 5 7 8 9 10 11 4 3 Distributeur de liquide de rinçage Distributeur de produit de lavage Panier à couverts Panier du bas Panier du haut 4.
FRANÇAIS 27 4.1 Voyants Indicateur Description Voyant XtraDry. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.com 5.1 Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 11 1.050 195 7 - 12 0.6 - 1.4 40 - 150 13 - 15 1.5 - 1.6 150 - 170 9 0.8 30 4 0.1 14 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut 29 vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage.
www.aeg.com 6.3 Notification de liquide de rinçage vide Quand la chambre du liquide de rinçage est vide, le voyant de liquide de rinçage s'allume pour signaler qu'un remplissage du liquide de rinçage est nécessaire. Si vous utilisez utilisez des pastilles touten-1 contenant un agent de rinçage et que vous êtes satisfait des résultats du séchage, vous pouvez désactiver la notification du remplissage du liquide de rinçage.
FRANÇAIS 31 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver d'options pendant le déroulement d'un programme. Certaines options ne sont pas compatibles entre elles. Si vous avez choisi des options incompatibles, l'appareil en désactivera automatiquement une ou plusieurs. Seuls les voyants correspondant aux options encore actives resteront allumés. 7.
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A D B 4. Enlevez le sel qui se trouve autour de l'ouverture du réservoir de sel régénérant. C B A M AX De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion. Afin d'éviter cela, après avoir rempli le réservoir de sel régénérant, démarrez un programme. 3 2 + 1 5. Tournez le couvercle du réservoir de sel régénérant vers la droite pour refermer le réservoir.
FRANÇAIS 33 Vous pouvez tourner le sélecteur de quantité délivrée (B) entre la position 1 (quantité minimale) et la position 4 ou 6 (quantité maximale). 9. UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. • Si le voyant du réservoir de sel régénérant est allumé, remplissez le réservoir. • Si le voyant du liquide de rinçage est allumé, remplissez le distributeur de liquide de rinçage.
www.aeg.com Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3. Appuyez sur la touche du programme que vous souhaitez lancer. L'affichage indique la durée du programme. 4. Sélectionnez les options compatibles. 5. Fermez la porte de l'appareil pour démarrer le programme. Démarrage d'un programme avec départ différé 1. Sélectionnez un programme.
FRANÇAIS • Lorsque vous chargez l'appareil, veillez à ce que l'eau libérée par les embouts des bras d'aspersion puisse atteindre parfaitement les plats pour qu'ils soient parfaitement lavés. Vérifiez que les plats ne se touchent pas ou ne se recouvrent pas les uns les autres. • Vous pouvez utiliser du détergent, du liquide de rinçage et du sel régénérant séparément, ou des pastilles tout en 1 (par ex. « 3 en 1 », « 4 en 1 » ou « tout en 1 »). Suivez les instructions indiquées sur l'emballage.
www.aeg.com • Vérifiez que les verres ne se touchent pas pour éviter qu'ils ne se brisent. • Placez les petits articles dans le panier à couverts. • Placez les objets légers dans le panier supérieur. Disposez-les de façon à ce qu'ils ne puissent pas se retourner. • Assurez-vous que le bras d'aspersion tourne librement avant de lancer un programme. 10.5 Avant le démarrage d'un programme Assurez-vous que : • Les filtres sont propres et correctement installés.
FRANÇAIS 37 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le vers la droite jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion.
www.aeg.com spécifique pour lave-vaisselle une fois par mois. Reportez-vous aux instructions figurant sur l'emballage de ces produits. 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête en cours de programme. Avant de contacter le service après-vente agréé, vérifiez si vous pouvez résoudre le problème par vous-même à l'aide des informations du tableau. Pour certaines anomalies, l'écran affiche un code d'alarme.
FRANÇAIS 39 Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 41 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com Pression de l'arrivée d'eau Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour d'autres valeurs.
DEUTSCH 43 INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE........................................................................................... 44 2. SICHERHEITSANWEISUNGEN.................................................................................45 3. GERÄTEBESCHREIBUNG......................................................................................... 47 4. BEDIENFELD..............................................................................................................47 5. PROGRAMME..
1. www.aeg.com SICHERHEITSHINWEISE Lesen Sie die mitgelieferte Gebrauchsanleitung sorgfältig vor Montage und Inbetriebnahme des Geräts. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
DEUTSCH • • • • • • • • 45 Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. Stellen Sie Messer und Besteck mit scharfen Spitzen mit der Spitze nach unten in den Besteckkorb oder legen Sie sie waagerecht in das Gerät.
www.aeg.com • • • • • • • Wenden Sie sich anderenfalls an eine Elektrofachkraft. Schließen Sie das Gerät unbedingt an eine sachgemäß installierte Schutzkontaktsteckdose an. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen.
DEUTSCH Produkt-Nummer (PNC): Seriennummer: • Trennen Sie das Gerät von der Stromversorgung. • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in dem Gerät einschließen. 2.6 Entsorgung WARNUNG! Verletzungs- und Erstickungsgefahr. 3.
www.aeg.com 3 Taste Delay 4 Programmwahltasten 5 Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe XtraDry. Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs. Kontrolllampe Salz. Sie erlischt während des Programmbetriebs. 5.
DEUTSCH Programm 5) Verschmutzungsgrad Beladung Programmphasen • Alle • Vorspülen 49 Optionen 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. (Dies ist das Standardprogramm für Prüfinstitute.) 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Körben. Es stellt dann automatisch die Wassertemperatur und -menge, den Energieverbrauch und die Programmdauer ein.
www.aeg.com 6.2 Wasserenthärter • Ein- oder Ausschalten der Klarspülmittelnachfüllanzeige. Der Wasserenthärter entfernt Mineralien aus dem Spülwasser, die sich nachteilig auf die Spülergebnisse und das Gerät auswirken könnten. Diese Einstellungen bleiben gespeichert, bis sie von Ihnen wieder geändert werden. Je höher der Mineralgehalt ist, um so härter ist das Wasser. Die Wasserhärte wird in gleichwertigen Einheiten gemessen.
DEUTSCH Benutzen Sie ein herkömmliches Reinigungsmittel oder MultiReinigungstabletten ohne Salz, stellen Sie die korrekte Wasserenthärterstufe ein, damit die Salznachfüllanzeige nicht ausgeschaltet wird. Ausschalten der Klarspülmittelnachfüllanzeige Das Gerät muss sich im Programmwahlmodus befinden. 1. Halten Sie zum Aufrufen des Einstellen des Wasserenthärters Benutzermodus gleichzeitig Das Gerät muss sich im Programmwahlmodus befinden.
www.aeg.com blinken und das Display nichts anzeigt. 2. Drücken Sie • Die Kontrolllampen . und erlöschen. • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle Einstellung angezeigt: – = Signalton ist ausgeschaltet. – = Signalton ist eingeschaltet. zum Ändern 3. Drücken Sie der Einstellung. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten.
DEUTSCH 8.1 Salzbehälter VORSICHT! Verwenden Sie nur Spezialsalz für Geschirrspüler. 53 8.2 Füllen des KlarspülmittelDosierers A D B Das Salz wird für die Regenerierung des Filterharzes im Wasserenthärter und zur Erzielung guter Spülergebnisse im täglichen Gebrauch benötigt. So füllen Sie den Salzbehälter: 1. Drehen Sie den Deckel des Salzbehälters gegen den Uhrzeigersinn und entfernen Sie ihn. 2. Füllen Sie 1 Liter Wasser in den Salzbehälter (nur beim ersten Mal). 3.
www.aeg.com 9. TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. • Füllen Sie den Salzbehälter auf, wenn die Kontrolllampe Salz leuchtet. • Leuchtet die Kontrolllampe Klarspülmittel, füllen Sie den Klarspülmittel-Dosierer. 3. Beladen Sie die Körbe. 4. Füllen Sie Reinigungsmittel ein. 5. Stellen Sie je nach Beladung und Verschmutzungsgrad das passende Programm ein. 9.
DEUTSCH Während des Countdowns kann die Zeitvorwahl weiter verlängert werden, es ist jedoch nicht möglich, die ausgewählten Programme und Optionen zu ändern. Nach Ablauf der Zeitvorwahl wird das Programm gestartet. Öffnen der Tür während eines laufenden Programms Wenn Sie die Tür während eines laufenden Programms öffnen, stoppt das Gerät. Dies kann sich auf den Energieverbrauch und die Programmdauer auswirken. Wenn Sie die Tür wieder schließen, läuft das Programm ab dem Zeitpunkt der Unterbrechung weiter.
www.aeg.com 10.2 Gebrauch von Salz, Klarspül- und Reinigungsmittel • Verwenden Sie nur Salz, Klarspülmittel und Reinigungsmittel für Geschirrspüler. Andere Produkte können das Gerät beschädigen. • Multi-Reinigungstabletten werden üblicherweise in Bereichen mit einer Wasserhärte von bis zu 21 °dH verwendet. In Bereichen, in denen diese Grenze überschritten wird, müssen zusätzlich zu den MultiReinigungstabletten Klarspülmittel und Salz verwendet werden.
DEUTSCH 10.6 Entladen der Körbe 1. Lassen Sie das Geschirr abkühlen, bevor Sie es aus dem Gerät nehmen. Heißes Geschirr ist stoßempfindlich. 2. Entladen Sie zuerst den Unter- und dann den Oberkorb. 57 Am Programmende kann sich noch Wasser an den Seitenwänden und der Gerätetür befinden. 11. REINIGUNG UND PFLEGE WARNUNG! Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden.
www.aeg.com 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein. Stellen Sie sicher, dass er korrekt unter den beiden Führungen eingesetzt wurde. 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.
DEUTSCH WARNUNG! Nicht ordnungsgemäße Reparaturen stellen ein Sicherheitsrisiko für den Benutzer dar. Die Reparaturarbeiten dürfen nur von qualifiziertem Personal durchgeführt werden. 59 Bei manchen Störungen zeigt das Display einen Alarmcode an. Die meisten Störungen, die auftreten, können behoben werden, ohne dass der autorisierte Kundendienst gerufen werden muss. Störung und Alarmcode Mögliche Ursache und Abhilfe Das Gerät lässt sich nicht einschalten.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Das Programm dauert zu lang. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie diese ab oder warten Sie, bis sie abgelaufen ist. Die verbleibende Zeit im Display erhöht sich und springt bis kurz vor die Programmende-Zeit. • Dies ist keine Störung. Das Gerät arbeitet ordnungsgemäß. Aus der Gerätetür tritt ein wenig Wasser aus. • Das Gerät ist nicht ausgerichtet.
DEUTSCH 61 12.1 Die Spül- und Trocknungsergebnisse sind nicht zufriedenstellend Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Spülergebnisse. • Siehe „Täglicher Gebrauch“, „Tipps und Hinweise“ sowie die Broschüre zum Beladen der Körbe. • Nutzen Sie intensivere Spülprogramme. • Reinigen Sie die Austrittsdüsen der Sprüharme und die Siebe. Siehe „Reinigung und Pflege“. Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät.
www.aeg.com Störung Mögliche Ursache und Abhilfe Rostspuren am Besteck. • Das Spülwasser enthält zu viel Salz. Siehe „Wasserenthärter“. • Silber- und Edelstahlbesteck wurden zusammen eingeordnet. Ordnen Sie nicht Silber- und Edelstahlbesteck zusammen ein. Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen.
DEUTSCH Leistungsaufnahme Aus-Zustand (W) 63 0.10 1) Weitere Angaben finden Sie auf dem Typenschild. 2) Wenn Sie Heißwasser mit umweltfreundlichen, alternativen Energiequellen (z. B. Solaranlagen oder Windkraft) aufbereiten, können Sie durch den Anschluss des Geräts an die Heißwasserversorgung Energie sparen. 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern.
156902650-A-012016 www.aeg.