NL FR DE Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle Benutzerinformation Geschirrspüler 2 22 43 F55345VI1
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 6 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen onder druk en/of stoom om het apparaat te reinigen.
NEDERLANDS ampère. Als de zekering van de stekker verwisseld moet worden, gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet. • Indien buizen lang niet zijn gebruikt, er reparaties hebben plaatsgevonden of er nieuwe apparaten zijn geplaatst (watermeters, enz.), moet u, voordat de nieuwe buizen worden aangesloten, het water laten stromen tot het schoon en helder is.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 2 1 11 10 1 2 3 4 5 6 9 8 7 6 Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 4 5 7 8 9 10 11 3 Glansmiddeldoseerbakje Afwasmiddeldoseerbakje Bestekkorf Onderkorf Bovenkorf 4.
NEDERLANDS 7 4.1 Indicatielampjes Aanduiding Beschrijving Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. 5.
www.aeg.com 5.1 Verbruiksgegevens Water (l) Energie(kWh) Programmaduur (min) P1 9.9 0.932 195 P2 7 - 12 0.6 - 1.4 40 - 150 P3 13 - 15 1.3 - 1.5 140 - 160 P4 9 0.9 30 P5 4 0.1 14 Programma 1) 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
NEDERLANDS Hoe hoger het gehalte van deze mineralen, des te harder is het water. De waterhardheid wordt gemeten in de volgende gelijkwaardige schalen. De waterontharder moet worden afgesteld op de hardheid van het water 9 in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten.
www.aeg.com die glansmiddel bevatten en u tevreden bent met het droogresultaat, kunt u de aanduiding voor het bijvullen van glansmiddel uitschakelen. We raden u echter aan voor de beste droogresultaten altijd glansmiddel te gebruiken. 6.4 Geluidssignalen Er klinken geluidssignalen als het apparaat een storing heeft. Het is niet mogelijk deze geluidssignalen uit te schakelen.
NEDERLANDS 11 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd. De opties kunnen niet worden in- of uitgeschakeld als een programma in werking is. Niet alle opties kunnen met elkaar worden gecombineerd. Als u opties hebt geselecteerd die niet met elkaar te combineren zijn, dan schakelt het apparaat automatisch één of meerdere opties uit. Alleen de indicatielampjes van de actieve opties blijven aan. 7.
www.aeg.com Het zoutreservoir vullen: 1. Draai de dop linksom om het zoutreservoir te openen. 2. Doe 1 liter water in het zoutreservoir (alleen de eerste keer). 3. Vul het zoutreservoir met regenereerzout. 8.2 Het vullen van het glansmiddeldoseerbakje A D B C B A 4. Verwijder het zout rond de opening van het zoutreservoir. M AX + 1 3 2 4 12 - C D 5. Draai de dop van het zoutreservoir rechtsom om het zoutreservoir te sluiten. Water en zout kunnen uit het zoutreservoir stromen als u het bijvult.
NEDERLANDS 13 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de programmakeuzemodus staat. • Vul het zoutreservoir als het zoutindicatielampje brandt. • Vul het glansmiddeldoseerbakje als het indicatielampje van het glansmiddel brandt. 3. Ruim de korven in. 4. Voeg vaatwasmiddel toe. 5. U dient het juiste programma in te stellen en te starten voor het type lading en de mate van vervuiling. 9.
www.aeg.com Als het aftelproces voltooid is, wordt het programma gestart. Houd tegelijkertijd Reset ingedrukt tot het apparaat in de programmakeuzemodus staat. De deur openen als het apparaat in werking is Het programma annuleren Als u de deur opent terwijl een programma loopt, stopt het apparaat. Het kan het energieverbruik en de programmaduur beïnvloeden. Als u de deur weer sluit, gaat het apparaat verder vanaf het punt van onderbreking.
NEDERLANDS achterblijven, raden we u aan om tabletten enkel bij lange programma's te gebruiken. • Gebruik niet meer dan de juiste hoeveelheid vaatwasmiddel. Zie de instructies van de vaatwasmiddelfabrikant. 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3.
www.aeg.com 11. ONDERHOUD EN REINIGING WAARSCHUWING! Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Vuile filters en verstopte sproeiarmen verminderen de wasresultaten. Controleer regelmatig de filters en reinig deze zo nodig. 3. Verwijder de platte filter (A). 4. Was de filters. 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten.
NEDERLANDS 17 • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 11.4 De binnenkant van de machine reinigen LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren. • Zorg dat de stekker in het stopcontact zit. • Zorg dat er geen zekering in de zekeringenkast is doorgebrand. Het programma begint niet. • Zorg dat de deur van het apparaat is gesloten. • Als startuitstel is ingesteld, annuleert u deze functie of wacht u tot het einde van het aftellen. • Het apparaat is begonnen met de oplaadprocedure van de hars in de waterontharder.
NEDERLANDS 19 Probleem en alarmcode Mogelijke oorzaak en oplossing De deur van het apparaat sluit moeilijk. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • Delen van het serviesgoed steken uit de korven. Ratelende / kloppende geluiden vanuit het apparaat. • Het serviesgoed is niet juist in de korven gerangschikt. Raadpleeg de folder voor het laden van de korven. • Zorg ervoor dat de sproeiarmen vrij kunnen ronddraaien. Het apparaat maakt kortsluiting.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Witte strepen of een blauwe waas op glazen en serviesgoed. • De vrijgegeven hoeveelheid glansmiddel is te hoog. Zet de dosering van het glansmiddel op een lagere stand. • Er is te veel vaatwasmiddel gebruikt. Vlekken en opgedroogde watervlekken op glazen en servies. • De vrijgegeven hoeveelheid glansmiddel is te laag. Zet de dosering van het glansmiddel op een hogere stand. • De kwaliteit van het glansmiddel kan de oorzaak zijn.
NEDERLANDS 21 Probleem Mogelijke oorzaak en oplossing Dof, ontkleurd of afgeschilverd serviesgoed. • Zorg dat alleen vaatwasmachinebestendige voorwerpen in het apparaat worden gewassen. • Laad de korf voorzichtig in en uit. Raadpleeg de folder voor het laden van de korven. • Leg tere voorwerpen in de bovenkorf. Raadpleeg "Voor het eerste gebruik", "Dagelijks gebruik" of "Aanwijzingen en tips" voor mogelijke andere oorzaken. 13.
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 23 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 24 3. DESCRIPTION DE L'APPAREIL.............................................................................. 26 4. BANDEAU DE COMMANDE................................................................................. 26 5. PROGRAMMES..........................
FRANÇAIS 1. 23 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 2 1 11 10 1 2 3 4 5 6 9 8 7 6 Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 4 5 7 8 9 10 11 3 Distributeur de liquide de rinçage Distributeur de produit de lavage Panier à couverts Panier du bas Panier du haut 4.
FRANÇAIS 27 4.1 Voyants Indicateur Description Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.com 5.1 Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) P1 9.9 0.932 195 P2 7 - 12 0.6 - 1.4 40 - 150 P3 13 - 15 1.3 - 1.5 140 - 160 P4 9 0.9 30 P5 4 0.1 14 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre 29 région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage.
www.aeg.com 6.3 Notification de liquide de rinçage vide Quand la chambre du liquide de rinçage est vide, le voyant de liquide de rinçage s'allume pour signaler qu'un remplissage du liquide de rinçage est nécessaire. Si vous utilisez utilisez des pastilles touten-1 contenant un agent de rinçage et que vous êtes satisfait des résultats du séchage, vous pouvez désactiver la notification du remplissage du liquide de rinçage.
FRANÇAIS 31 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver d'options pendant le déroulement d'un programme. Certaines options ne sont pas compatibles entre elles. Si vous avez choisi des options incompatibles, l'appareil en désactivera automatiquement une ou plusieurs. Seuls les voyants correspondant aux options encore actives resteront allumés. 7.
www.aeg.com procédure achevée. La procédure sera répétée régulièrement. 8.1 Réservoir de sel régénérant ATTENTION! Utilisez uniquement du sel régénérant conçu pour les lave-vaisselle. Le sel permet de recharger la résine dans l'adoucisseur d'eau et de garantir de bons résultats de lavage en utilisation quotidienne. De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion.
FRANÇAIS 4. Fermez le couvercle. Assurez-vous que le bouton d'ouverture se verrouille correctement. 33 Vous pouvez tourner le sélecteur de quantité délivrée (B) entre la position 1 (quantité minimale) et la position 4 ou 6 (quantité maximale). 9. UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. • Si le voyant du réservoir de sel régénérant est allumé, remplissez le réservoir.
www.aeg.com Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3. Appuyez à plusieurs reprises sur la touche ou jusqu'à ce que l'affichage indique le numéro du programme que vous souhaitez lancer. Le numéro du programme s'affiche pendant environ 3 secondes, puis la durée du programme s'affiche. 4. Sélectionnez les options compatibles. 5.
FRANÇAIS • • • • programme avec une phase de prélavage. Utilisez toujours tout l'espace des paniers. Lorsque vous chargez l'appareil, veillez à ce que l'eau libérée par les embouts des bras d'aspersion puisse atteindre parfaitement les plats pour qu'ils soient parfaitement lavés. Vérifiez que les plats ne se touchent pas ou ne se recouvrent pas les uns les autres. Vous pouvez utiliser du détergent, du liquide de rinçage et du sel régénérant séparément, ou des pastilles tout en 1 (par ex.
www.aeg.com • La vaisselle et les couverts ne doivent pas être insérés les uns dans les autres ni se chevaucher. Mélangez les cuillères avec d'autres couverts. • Vérifiez que les verres ne se touchent pas pour éviter qu'ils ne se brisent. • Placez les petits articles dans le panier à couverts. • Placez les objets légers dans le panier supérieur. Disposez-les de façon à ce qu'ils ne puissent pas se retourner. • Assurez-vous que le bras d'aspersion tourne librement avant de lancer un programme. 10.
FRANÇAIS 37 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le vers la droite jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion.
www.aeg.com spécifique pour lave-vaisselle une fois par mois. Reportez-vous aux instructions figurant sur l'emballage de ces produits. 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête en cours de programme. Avant de contacter le service après-vente agréé, vérifiez si vous pouvez résoudre le problème par vous-même à l'aide des informations du tableau. Pour certaines anomalies, l'écran affiche un code d'alarme.
FRANÇAIS 39 Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 41 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com Pression de l'arrivée d'eau Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour d'autres valeurs.
DEUTSCH 43 INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE.........................................................................................44 2. SICHERHEITSANWEISUNGEN.............................................................................. 45 3. GERÄTEBESCHREIBUNG.......................................................................................47 4. BEDIENFELD........................................................................................................... 47 5. PROGRAMME............
1. www.aeg.com SICHERHEITSHINWEISE Lesen Sie die mitgelieferte Gebrauchsanleitung sorgfältig vor Montage und Inbetriebnahme des Geräts. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
DEUTSCH • • • • • • • • 45 Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. Stellen Sie Messer und Besteck mit scharfen Spitzen mit der Spitze nach unten in den Besteckkorb oder legen Sie sie waagerecht in das Gerät.
www.aeg.com • • • • • • • Wenden Sie sich anderenfalls an eine Elektrofachkraft. Schließen Sie das Gerät unbedingt an eine sachgemäß installierte Schutzkontaktsteckdose an. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen.
DEUTSCH Produkt-Nummer (PNC): Seriennummer: • Trennen Sie das Gerät von der Stromversorgung. • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in dem Gerät einschließen. 2.6 Entsorgung WARNUNG! Verletzungs- und Erstickungsgefahr. 3.
www.aeg.com 3 4 5 6 Taste Delay Programmtaste (nach oben) Programmtaste (nach unten) Taste XtraDry 7 Taste TimeSaver 8 Taste Reset 9 Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs. Kontrolllampe Salz. Sie erlischt während des Programmbetriebs. 5.
DEUTSCH Programm Verschmutzungsgrad Beladung Programmphasen P5 • Alle • Vorspülen 49 Optionen 5) 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. (Dies ist das Standardprogramm für Prüfinstitute.) 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Körben. Es stellt dann automatisch die Wassertemperatur und -menge, den Energieverbrauch und die Programmdauer ein.
www.aeg.com 6. EINSTELLUNGEN 6.1 Programmwahlmodus und Benutzermodus Wenn sich das Gerät im Programmwahlmodus befindet, kann ein Programm eingestellt und der Benutzermodus aufgerufen werden. Im Benutzermodus können folgende Einstellungen geändert werden: • Die Stufe des Wasserenthärters gemäß der Wasserhärte. • Ein- und Ausschalten des Signaltons für das Programmende. • Ein- oder Ausschalten der Klarspülmittelnachfüllanzeige.
DEUTSCH Wenn Sie Multi-Reinigungstabletten verwenden, die Salz enthalten und die Wasserhärte in Ihrem Gebiet unter 21°dH ist, können Sie die niedrigste Wasserenthärterstufe einstellen. Auf diese Weise wird die Salznachfüllanzeige ausgeschaltet. Benutzen Sie ein herkömmliches Reinigungsmittel oder MultiReinigungstabletten ohne Salz, stellen Sie die korrekte Wasserenthärterstufe ein, damit die Salznachfüllanzeige nicht ausgeschaltet wird.
www.aeg.com gedrückt, bis die Kontrolllampen , und blinken und das Display nichts anzeigt. 2. Drücken Sie . • Die Kontrolllampen erlöschen. und • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle Einstellung angezeigt: – = Signalton ist ausgeschaltet. – = Signalton ist eingeschaltet. zum Ändern der 3. Drücken Sie Einstellung. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten.
DEUTSCH 3. Füllen Sie den KlarspülmittelDosierer. 4. Öffnen Sie den Wasserhahn. 5. Starten Sie ein Programm, um Fertigungsrückstände, die sich möglicherweise noch im Gerät befinden können, zu beseitigen. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. Wenn Sie ein Programm starten, kann es bis zu 5 Minuten dauern das Filterharz des Wasserenthärters zu regenerieren. Das Gerät scheint nicht zu arbeiten. Die Spülphase startet erst nach Abschluss dieses Vorgangs.
www.aeg.com ACHTUNG! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. Tuch auf, um zu große Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet. 1. Drücken Sie die Entriegelungstaste (D), um den Deckel (C) zu öffnen. 2. Füllen Sie den KlarspülmittelDosierer (A) bis zur Markierung „max“. 3.
DEUTSCH • Nach 5 Minuten, wenn das Programm nicht gestartet wurde. Starten eines Programms 1. Lassen Sie die Gerätetür einen Spaltbreit offen. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. 3. Drücken Sie wiederholt oder , bis im Display die Nummer des gewünschten Programms erscheint. Die Programmnummer wird etwa 3 Sekunden lang im Display angezeigt, anschließend erscheint die Programmdauer. 4.
www.aeg.com • Schütten Sie größere Lebensmittelreste auf dem Geschirr in den Abfallbehälter. • Spülen Sie das Geschirr nicht von Hand vor. Verwenden Sie bei Bedarf das Vorspülprogramm (wenn verfügbar) oder wählen Sie ein Programm mit Vorspülgang. • Nutzen Sie die Körbe immer ganz aus. • Wenn Sie das Gerät beladen, achten Sie darauf, dass das Geschirr komplett von dem Wasser aus den Sprüharmdüsen erreicht und gespült wird.
DEUTSCH • Achten Sie darauf, dass Gläser einander nicht berühren. • Ordnen Sie kleine Gegenstände in den Besteckkorb ein. • Ordnen Sie leichte Gegenstände im Oberkorb an. Achten Sie darauf, dass diese nicht verrutschen können. • Vergewissern Sie sich, dass sich der Sprüharm ungehindert bewegen kann, bevor Sie ein Programm starten. 10.5 Vor dem Starten eines Programms • Die Geschirrteile sind richtig in den Körben angeordnet. • Das Programm eignet sich für die Beladung und den Verschmutzungsgrad.
www.aeg.com 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. 4. Reinigen Sie die Filter. ACHTUNG! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 5.
DEUTSCH 11.4 Reinigung des Geräteinnenraums • Reinigen Sie das Gerät und die Gummidichtung der Tür sorgfältig mit einem weichen, feuchten Tuch. • Wenn Sie regelmäßig Kurzprogramme verwenden, können diese zu Fett- und Kalkablagerungen im Gerät führen. Um dieses zu vermeiden, wird empfohlen, 59 mindestens zweimal im Monat Programme mit langer Laufzeit zu verwenden.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Es läuft kein Wasser in das Gerät. • Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist. • Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Informationen erhalten Sie von Ihrem lokalen Wasserversorger. • Stellen Sie sicher, dass der Wasserzulaufhahn nicht verstopft ist. • Vergewissern Sie sich, dass der Filter im Zulaufschlauch nicht verstopft ist.
DEUTSCH 61 Störung und Alarmcode Mögliche Ursache und Abhilfe Klappernde/schlagende Geräusche aus dem Geräteinneren. • Das Geschirr ist nicht richtig in den Körben eingeordnet. Siehe Broschüre zum Beladen der Körbe. • Achten Sie darauf, dass sich die Sprüharme frei drehen können. Das Gerät löst die Sicherung • Die abgesicherte Stromstärke reicht nicht für den gleichaus. zeitigen Betrieb aller eingeschalteten Geräte. Überprüfen Sie, für welche Stromstärke die Steckdose bzw.
www.aeg.com Störung Mögliche Ursache und Abhilfe Wasserflecken und andere Flecken auf Gläsern und Geschirr. • Die zugegebene Klarspülmittelmenge ist zu niedrig. Stellen Sie eine höhere Klarspülmittelmenge ein. • Die Ursache kann in der Qualität des Klarspülmittels liegen. Das Geschirr ist nass. • Schalten Sie die Option XtraDry ein, um die beste Trocknungsleistung zu erzielen. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur.
DEUTSCH Störung Mögliche Ursache und Abhilfe Das Geschirr ist glanzlos, verfärbt sich oder ist angeschlagen. • Achten Sie darauf, dass nur spülmaschinenfestes Geschirr im Gerät gespült wird. • Laden und entladen Sie den Korb vorsichtig. Siehe Broschüre zum Beladen der Körbe. • Ordnen Sie empfindliche Gegenstände im Oberkorb an. 63 Siehe „Vor der ersten Inbetriebnahme“, „Täglicher Gebrauch“ oder „Tipps und Hinweise“ bezüglich anderer möglicher Ursachen. 13.
156902440-A-022016 www.aeg.