CS PL Návod k použití Myčka nádobí Instrukcja obsługi Zmywarka 2 20 FAVORIT 55602 W0P
www.aeg.com OBSAH 1. BEZPEČNOSTNÍ INFORMACE......................................................................... 3 2. BEZPEČNOSTNÍ POKYNY................................................................................4 3. POPIS SPOTŘEBIČE.........................................................................................5 4. OVLÁDACÍ PANEL ............................................................................................6 5. PROGRAMY....................................................
ČESKY 1. 3 BEZPEČNOSTNÍ INFORMACE Tento návod si pečlivě přečtěte ještě před instalací spotřebiče a jeho prvním použitím. Výrobce nezodpovídá za škody a zranění způsobená nesprávnou instalací či chybným používáním. Návod k použití vždy uchovávejte spolu se spotřebičem pro jeho budoucí použití. 1.
www.aeg.com 1.2 Bezpečnost dětí a postižených osob • • • • • Tento spotřebič smí používat děti starší osmi let nebo osoby se sníženými fyzickými, smyslovými nebo duševními schopnostmi nebo osoby bez patřičných zkušeností a znalostí, pouze pokud tak činí pod dozorem nebo vedením, které zohledňuje bezpečný provoz spotřebiče, a pokud rozumí rizikům spojeným s provozem spotřebiče. Nenechte děti hrát si se spotřebičem. Všechny prací prostředky uschovejte z dosahu dětí.
ČESKY • • • • • UPOZORNĚNÍ! Nebezpečné napětí. Jestliže se přívodní hadice poškodí, okamžitě vytáhněte síťovou zástrčku ze zásuvky. Zkontaktujte autorizované servisní středisko, aby vám přívodní hadici vyměnilo. 2.4 Použití spotřebiče • • Na otevřená dvířka si nesedejte, ani si na ně nestoupejte. Mycí prostředky pro myčky jsou nebezpečné. Řiďte se bezpečnostními pokyny uvedenými na balení mycího prostředku. Nepijte ani si nehrajte s vodou ve spotřebiči.
www.aeg.com 5 6 7 8 9 Filtry Typový štítek Zásobník na sůl Větrací otvor Dávkovač leštidla 10 11 12 13 Dávkovač mycího prostředku Košíček na příbory Dolní koš Horní koš 4. OVLÁDACÍ PANEL 1 2 8 1 2 3 4 5 Tlačítko Zap/Vyp Tlačítko Program Kontrolky programů Displej Tlačítko Delay 3 4 7 5 6 6 Tlačítko Start 7 Kontrolky 8 Tlačítko Option 4.1 Kontrolky Kontrolka Popis Fáze mytí. Rozsvítí se, když probíhá mycí nebo oplachovací fáze. Fáze sušení. Rozsvítí se během fáze sušení.
ČESKY 7 5.
www.aeg.com Program 1) Voda (l) Energie (kWh) Délka (min) 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 4 0.1 14 1) Hodnoty se mohou měnit v závislosti na tlaku a teplotě vody, na kolísání v dodávce proudu, na zvole‐ ných funkcích a na množství nádobí. 5.2 Informace pro zkušebny Pro všechny potřebné informace ohledně testu výkonnosti zašlete e-mail na: Poznamenejte si výrobní číslo (PNC) uvedené na typovém štítku. info.test@dishwasher-production.com 6.
ČESKY 9 Tvrdost vody Německé stupně (°dH) Francouzské stupně (°fH) mmol/l Clarkovy stupně Nastavení změkčo‐ vače vody 47 - 50 84 - 90 8,4 - 9,0 58 - 63 10 43 - 46 76 - 83 7,6 - 8,3 53 - 57 9 37 - 42 65 - 75 6,5 - 7,5 46 - 52 8 29 - 36 51 - 64 5,1 - 6,4 36 - 45 7 23 - 28 40 - 50 4,0 - 5,0 28 - 35 6 19 - 22 33 - 39 3,3 - 3,9 23 - 27 5 1) 15 - 18 26 - 32 2,6 - 3,2 18 - 22 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 3 4 - 10 7 - 18 0,7 - 1,8 5 - 12 2 <4 <7 <0,7 <5
www.aeg.com – Stupeň 0 = neuvolňuje se žádné leštidlo. 3. Opětovným stisknutím Delay změňte nastavení. 4. Potvrďte nastavení stisknutím tlačítka Zap/Vyp. 6.4 Použití leštidla spolu s kombinovanými mycími tabletami Když zapnete funkci Multitab, dávkovač leštidla dále uvolňuje leštidlo. Tento dávkovač leštidla však můžete vypnout. V takovém případě nemusí být výsledky sušení uspokojivé. S vypnutým dávkovačem leštidla kontrolka leštidla nikdy nesvítí.
ČESKY 11 7.1 Multitab 7.2 TimeSaver Tuto funkci zapněte, když používáte kombinované mycí tablety, které obsahují sůl, leštidlo a mycí prostředek. Mohou také obsahovat další čisticí nebo oplachovací prostředky. Tato funkce zvyšuje tlak a teplotu vody. Mycí a sušicí fáze jsou kratší. Tato funkce vypne dávkování soli. Kontrolka soli se nerozsvítí. Při použití této funkce se délka programu prodlouží s cílem zlepšit při použití kombinovaných tablet výsledky mytí a sušení.
www.aeg.com POZOR! Používejte pouze leštidlo pro myčky nádobí. 5. Zavřete zásobník na sůl otočením jeho víčka po směru hodinových ručiček. Při plnění může ze zásobníku na sůl unikat voda nebo sůl. Nebezpečí koroze. Po naplnění zásobníku na sůl jí zabráníte spuštěním programu. 1. Otevřete víko (C). 2. Doplňte dávkovač leštidla (B), dokud kapalina nedosáhne hladiny „MAX“. 3. Rozlité leštidlo setřete savým hadříkem, aby se netvořilo přílišné množství pěny. 4. Zavřete víko.
ČESKY 9.1 Použití mycího prostředku A B 13 kontrolka vámi požadovaného programu. Na displeji se zobrazí délka programu. 4. Zvolte použitelné funkce. 5. Stiskněte Start ke spuštění programu. • Rozsvítí se kontrolka mycí fáze. • Délka programu se začne snižovat v krocích po jedné minutě. Spuštění programu s odloženým startem C POZOR! Používejte pouze mycí prostředek pro myčky nádobí. 1. Stiskněte uvolňovací tlačítko (A) a otevřete víko (C). 2. Mycí prostředek či tabletu vložte do komory (B). 3.
www.aeg.com Zrušení programu Současně stiskněte a podržte Program a Option, dokud se spotřebič nepřepne do režimu volby programu. Před spuštěním nového programu zkontrolujte, zda je v dávkovači mycí prostředek. Konec programu Žádná tlačítka kromě tlačítka Zap/Vyp nesvítí. 1. Stiskněte tlačítko Zap/Vyp nebo vyčkejte, až funkce Auto Off automaticky vypne spotřebič. Pokud jste otevřeli dvířka před zapnutím Auto Off, spotřebič se automaticky vypne. 2. Zavřete vodovodní kohoutek.
ČESKY 10.3 Co dělat, pokud chcete přestat používat mycí tablety • Než začnete odděleně používat mycí prostředek, sůl a leštidlo, proveďte následující postup. • 1. Nastavte nejvyšší stupeň změkčovače vody. 2. Ujistěte se, že je zásobník na sůl a dávkovač leštidla plný. 3. Nastavte nejkratší program s oplachovací fází. Nepoužívejte mycí prostředek a nevkládejte nic do košů. 4. Po dokončení programu nastavte změkčovač vody na stupeň tvrdosti vody v místě vašeho bydliště. 5. Seřiďte dávkování leštidla.
www.aeg.com C B A 1. Otočte filtrem (B) proti směru hodinových ručiček a vyndejte jej. 2. Vyndejte filtr (C) z filtru (B). 3. Vyjměte plochý filtr (A). 5. Zkontrolujte, zda ve sběrné jímce nebo kolem ní nejsou žádné zbytky jídel a nečistot. 6. Vložte zpět plochý filtr (A). Ujistěte se, že je správně umístěn pod dvěma vodicími drážkami. 7. Sestavte filtry (B) a (C). 8. Vložte zpět filtr (B) do plochého filtru (A). Otočte jím po směru hodinových ručiček, dokud se nezajistí. 4. Filtry omyjte.
ČESKY 11.2 Čištění ostřikovacích ramen 11.4 Čištění vnitřního prostoru Ostřikovací ramena nevyjímejte. Jestliže se otvory v ostřikovacích ramenech zanesou nečistotami, odstraňte je úzkým špičatým předmětem. • 11.3 Čištění vnějších ploch • • • Vyčistěte spotřebič vlhkým měkkým hadrem. Používejte pouze neutrální mycí prostředky. Nepoužívejte prostředky s drsnými částicemi, drátěnky nebo rozpouštědla. • 17 Pečlivě očistěte spotřebič včetně pryžového těsnění dvířek vlhkým měkkým hadříkem.
www.aeg.com Problém a výstražný kód Možné řešení Je aktivován bezpečnostní systém proti vyplavení. • Na displeji se zobrazí Zavřete vodovodní kohoutek a obraťte se na autorizo‐ vané servisní středisko. . Po kontrole spotřebiče jej vypněte a znovu zapněte. Pokud se problém objeví znovu, obraťte se na autorizované servisní středisko. Při výskytu výstražných kódů, které nejsou uvedené v tabulce, se obraťte na autorizované servisní středisko. 12.
ČESKY Příkon Režim vypnuto (W) 0.10 1) Ohledně ostatních údajů viz typový štítek. 2) Pokud odebíráte horkou vodu z alternativních zdrojů (např. solární panely, větrná energie), použijte tuto horkou vodu ke snížení spotřeby energie. 14. POZNÁMKY K OCHRANĚ ŽIVOTNÍHO PROSTŘEDÍ Recyklujte materiály označené symbolem . Obaly vyhoďte do příslušných odpadních kontejnerů k recyklaci. Pomáhejte chránit životní prostředí a lidské zdraví a recyklovat elektrické a elektronické spotřebiče určené k likvidaci.
www.aeg.com SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA......................................... 21 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA.......................................... 22 3. OPIS URZĄDZENIA......................................................................................... 24 4. PANEL STEROWANIA ....................................................................................25 5. PROGRAMY........................................................................................
POLSKI 1. 21 INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA Przed instalacją i rozpoczęciem eksploatacji urządzenia należy uważnie zapoznać się z załączoną instrukcją obsługi. Producent nie odpowiada za uszkodzenia i obrażenia ciała spowodowane nieprawidłową instalacją i eksploatacją. Należy zachować instrukcję wraz z urządzeniem do wykorzystania w przyszłości. 1.
www.aeg.com • Urządzenie należy podłączyć do instalacji wodociągowej za pomocą nowego zestawu węży dostarczonych w komplecie z urządzeniem. Nie wolno używać starego zestawu węży. 1.
POLSKI • • • • • • • Należy używać wyłącznie prawidłowo zamontowanego gniazda elektrycznego z uziemieniem. Nie stosować rozgałęźników ani przedłużaczy. Należy zwrócić uwagę, aby nie uszkodzić wtyczki ani przewodu zasilającego. Wymiany przewodu zasilającego można dokonać wyłącznie w naszym autoryzowanym centrum serwisowym. Podłączyć wtyczkę do gniazda elektrycznego dopiero po zakończeniu instalacji. Należy zadbać o to, aby w zainstalowanym urządzeniu wtyczka przewodu zasilającego była łatwo dostępna.
www.aeg.com • Wymontować zatrzask drzwi, aby uniemożliwić zamknięcie się dzieci lub zwierząt w urządzeniu. 3.
POLSKI 4. PANEL STEROWANIA 1 2 8 1 2 3 4 5 3 4 7 Przycisk wł./wył. Przycisk Program Wskaźniki programów Wyświetlacz Przycisk Delay 5 6 6 Przycisk Start 7 Wskaźniki 8 Przycisk Option 4.1 Wskaźniki Wskaźnik Opis Faza zmywania. Włącza się podczas fazy zmywania oraz fazy płukania. Faza suszenia. Zapala się podczas fazy suszenia. Wskaźnik funkcji Multitab. Wskaźnik soli. W trakcie programu wskaźnik ten jest zawsze wyłączony. Wskaźnik płynu nabłyszczającego.
www.aeg.com 5.
POLSKI 27 5.1 Parametry eksploatacyjne Program1) Zużycie wody (l) Zużycie energii (kWh) Czas trwania (min) 10.2 0.932 225 7 - 14 0.6 - 1.4 40 - 150 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 4 0.1 14 1) Parametry eksploatacyjne mogą ulec zmianie w zależności od ciśnienia i temperatury wody, zmian w napięciu zasilania, użytych opcji oraz ilości naczyń. 5.
www.aeg.com Im wyższa zawartość substancji mineralnych, tym twardsza jest woda. Twardość wody jest mierzona w równoważnych skalach. doprowadzonej do urządzenia. W lokalnym zakładzie wodociągowym można uzyskać informację na temat twardości wody. Istotne jest ustawienie właściwego poziomu zmiękczania wody, aby zapewnić dobre rezultaty zmywania.
POLSKI Ustawienie fabryczne: poziom 4. Regulacja dozowania płynu nabłyszczającego Urządzenie musi być w trybie wyboru programów. 1. Aby uruchomić tryb użytkownika, nacisnąć jednocześnie i przytrzymać przyciski Delay i Start, aż wskaźniki , , i zaczną migać, a wyświetlacz będzie pusty. 2. Nacisnąć Delay. , i • Wskaźniki wyłączą się. • Wskaźnik będzie nadal migał. Na wyświetlaczu pojawi się • = aktualne ustawienie: np. poziom 4. – Poziom dozowania płynu nabłyszczającego można ustawić od 0A do 6A.
www.aeg.com • Wskaźniki , i wyłączą się. • • Wskaźnik będzie nadal migał. Na wyświetlaczu pojawi się = sygnał dźwiękowy włączony. 4. Nacisnąć przycisk wł./wył., aby potwierdzić ustawienie. = sygnał aktualne ustawienie: dźwiękowy wyłączony. 3. Nacisnąć Start, aby zmienić ustawienie. 7. OPCJE Żądane opcje należy zawsze włączać przed uruchomieniem programu. Opcji nie można włączać ani wyłączać w trakcie programu. Nie wszystkie opcje są ze sobą zgodne.
POLSKI mogące wciąż znajdować się w urządzeniu. Nie należy stosować detergentu ani umieszczać naczyń w koszach. Po uruchomieniu programu urządzenie zaczyna doprowadzać żywicę do zmiękczacza wody – może to potrwać do 5 minut. Może wydawać się, że urządzenie nie pracuje. Program rozpoczyna się dopiero po zakończeniu tego procesu. Proces ten jest powtarzany co pewien czas. 8.1 Zbiornik soli 31 Podczas napełniania zbiornika soli może się z niego wydostawać woda i sól. Zagrożenie wystąpieniem korozji.
www.aeg.com 9. CODZIENNA EKSPLOATACJA 1. Otworzyć zawór wody. 2. Nacisnąć przycisk wł./wył., aby włączyć urządzenie. Upewnić się, że urządzenie jest w trybie użytkownika. • Jeśli świeci się wskaźnik soli, napełnić zbiornik soli. • Jeśli świeci się wskaźnik płynu nabłyszczającego, napełnić dozownik płynu nabłyszczającego. 3. Załadować kosze. 4. Dodać detergent. Aby stosować tabletki wieloskładnikowe, należy włączyć funkcję Multitab. 5.
POLSKI – Od 24 do 11 godzin czas będzie odliczany co 1 godzinę. – Od 10 do 1 godziny czas będzie odliczany co 1 minutę. Po zakończeniu odliczania nastąpi uruchomienie programu. Otwieranie drzwi w trakcie pracy urządzenia Otworzenie drzwi w trakcie działania programu powoduje zatrzymanie urządzenia. Po zamknięciu drzwi urządzenie kontynuuje pracę od momentu, w którym została przerwana. Po otworzeniu drzwi na dłużej niż 30 sekund podczas fazy suszenia, bieżący program zostanie zakończony.
www.aeg.com 10.2 Stosowanie soli, płynu nabłyszczającego i detergentu • • • • • Należy stosować wyłącznie sól, płyn nabłyszczający i detergent do zmywarek. Inne produkty mogą uszkodzić urządzenie. Tabletki wieloskładnikowe są zwykle przeznaczone do użycia z wodą o twardości do 21°dH. Gdy twardość wody jest większa, należy oprócz tabletek wieloskładnikowych stosować także płyn nabłyszczający i sól.
POLSKI • • • (chyba że stosowane są wieloskładnikowe tabletki z detergentem); ułożenie naczyń i przyborów kuchennych w koszach jest prawidłowe; program jest odpowiedni dla danego rodzaju załadunku i stopnia zabrudzenia; użyto prawidłową ilość detergentu. 10.6 Opróżnianie koszy 1. Przed wyjęciem naczyń ze zmywarki poczekać, aż wystygną. Gorące naczynia łatwo ulegają uszkodzeniu. 2. Najpierw wyjmować naczynia z dolnego kosza, a potem z górnego.
www.aeg.com UWAGA! Nieprawidłowe umiejscowienie filtrów może skutkować niezadowalającymi efektami zmywania i uszkodzeniem urządzenia. 11.2 Czyszczenie ramion spryskujących 5. Upewnić się, że wokół krawędzi osadnika nie znajdują się resztki żywności ani zanieczyszczenia. 6. Włożyć na miejsce filtr płaski (A). Upewnić się, że jest prawidłowo umieszczony pod 2 prowadnicami. Nie wolno wyjmować ramion spryskujących.
POLSKI należy sprawdzić, czy problem można rozwiązać samodzielnie, korzystając z informacji zawartych w tabeli. Przy niektórych usterkach na wyświetlaczu pojawia się kod alarmowy. Problem i kod alarmowy Możliwe rozwiązanie Urządzenie nie włącza się. • Upewnić się, że wtyczka przewodu zasilającego jest włożona do gniazdka. Upewnić się, że bezpiecznik w skrzynce bezpieczników jest sprawny. • Program nie uruchamia się. • • • Upewnić się, że drzwi urządzenia są zamknięte. Nacisnąć Start.
www.aeg.com Problem Możliwe rozwiązanie Plamy i ślady po odparowa‐ • nych kroplach wody na szklan‐ kach i naczyniach. • Za mało płynu nabłyszczającego. Obrócić pokrętło regulacji dozowania płynu nabłyszczającego, aby zwiększyć dozowanie. Przyczyną może być jakość płynu nabłyszczającego. Naczynia są mokre. Program nie obejmuje fazy suszenia lub faza suszenia odbywa się w niskiej temperaturze. Dozownik płynu nabłyszczającego jest pusty. Przyczyną może być jakość płynu nabłyszczającego.
POLSKI recyklingu lub skontaktować się z odpowiednimi lokalnymi władzami.
117900980-B-172014 www.aeg.