NL FR DE Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle Benutzerinformation Geschirrspüler 2 24 47 FAVORIT 55700VI1P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant. 2.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Top sproeiarm Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 Beam-on-Floor De Beam-on-Floor is een lichtstraal die op de keukenvloer onder de deur van het apparaat verschijnt. • Wanneer het programma start, gaat de rode lichtstraal aan. De lichtstraal blijft gedurende het volledige programma zichtbaar. • Wanneer het programma is voltooid, gaat het groene lampje branden.
NEDERLANDS 4. BEDIENINGSPANEEL 1 1 2 3 4 5 2 Aan/uit-toets Weergave Delay-toets Programmakeuzetoets (omhoog) Programmakeuzetoets (omlaag) 3 4 6 7 8 9 5 6 7 8 9 TimeSaver-toets XtraDry-toets RESET-toets Indicatielampjes 4.1 Indicatielampjes Aanduiding Beschrijving Einde-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. 5.
www.aeg.com Programma Mate van vervuiling Type belading Programmafasen Opties P4 • Pas bevuild • Serviesgoed en bestek • Wassen 60 °C • Spoelingen • XtraDry • Alle • Voorspoelen 4) P5 5) 1) Dit programma biedt het meest efficiënte water- en energieverbruik voor normaal vervuild serviesgoed en bestek. (Dit is het standaard programma voor testinstituten). 2) Het apparaat detecteert de mate van vervuiling en de hoeveelheid serviesgoed in de korven.
NEDERLANDS 9 6. INSTELLINGEN 6.1 Programmakeuzemodus en gebruikersmodus Als het apparaat in de programmakeuzemodus staat, kan een programma worden ingesteld en de gebruikersmodus worden ingevoerd. Als u het apparaat activeert, staat het meestal in de programmakeuzemodus. Maar als dit niet gebeurt, kunt u de programmakeuzemodus op de volgende manier instellen: Houd tegelijkertijd RESET ingedrukt tot het apparaat in de programmakeuzemodus staat.
www.aeg.com Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau <4 <7 <0.7 <5 1 2) 1) Fabrieksinstelling. 2) Gebruik geen zout op dit niveau. Indien u gebruik maakt van multitabletten die zout bevatten en de waterhardheid lager is dan 21°dH, kunt u het laagste wateronthardingsniveau instellen. Het deactiveert de aanduiding voor het bijvullen van zout.
NEDERLANDS bent met het droogresultaat, kunt u de aanduiding voor het bijvullen van glansmiddel uitschakelen. We raden u echter aan voor de beste droogresultaten altijd glansmiddel te gebruiken. 6.5 Geluidssignalen Schakel de aanduiding in om de glansmiddelindicator actief te houden als u standaard wasmiddel of multitabletten zonder glansmiddel bevat. Na het beëindigen van het programma klinkt er tevens een geluidssignaal. Dit geluidssignaal is standaard uitgeschakeld, maar kan worden geactiveerd.
www.aeg.com 7.1 XtraDry 7.2 TimeSaver Activeer deze optie als u het droogresultaat een boost wilt geven. Bij het gebruik van deze optie kunnen de duur van sommige programma´s, het waterverbruik en de temperatuur van de laatste spoeling worden beïnvloed. Met deze optie verhoogt u de druk en de temperatuur van het water. De wasen droogfasen zijn korter. De optie XtraDry is geen permanente optie en moet elke cyclus geselecteerd worden. Het activeren van XtraDry .
NEDERLANDS 13 8.2 Het vullen van het glansmiddeldoseerbakje A B 4. Verwijder het zout rond de opening van het zoutreservoir. C 5. Draai de dop van het zoutreservoir rechtsom om het zoutreservoir te sluiten. Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Gevaar voor roest. Start om dit te voorkomen een programma nadat u het zoutreservoir heeft bijgevuld. LET OP! Gebruik alleen glansmiddel voor afwasautomaten. 1. Open het deksel (C). 2.
www.aeg.com 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de programmakeuzemodus staat. • Vul het zoutreservoir als het zoutindicatielampje brandt. • Vul het glansmiddeldoseerbakje als het indicatielampje van het glansmiddel brandt. 3. Ruim de korven in. 4. Voeg vaatwasmiddel toe. 5. U dient het juiste programma in te stellen en te starten voor het type lading en de mate van vervuiling. 9.
NEDERLANDS De deur openen als het apparaat in werking is Als u de deur opent terwijl een programma loopt, stopt het apparaat. Het kan het energieverbruik en de programmaduur beïnvloeden. Als u de deur weer sluit, gaat het apparaat verder vanaf het punt van onderbreking. Als de deur tijdens de droogfase langer dan 30 seconden wordt geopend, stopt het lopende programma.
www.aeg.com • Gebruik niet meer dan de juiste hoeveelheid vaatwasmiddel. Zie de instructies van de vaatwasmiddelfabrikant. 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase.
NEDERLANDS 17 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
www.aeg.com 11.2 De bovenste sproeiarm schoonmaken We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt. naar boven in de richting van de lagere pijl en draait u hem tegelijkertijd tegen de wijzers van de klok in, zodat hij op zijn plek vergrendelt. Verstopte gaten kunnen onbevredigende wasresultaten opleveren. 1. Trek het bovenrek naar buiten. 2.
NEDERLANDS WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. 19 Bij sommige problemen wordt er op de display een alarmcode weergegeven. Het merendeel van de problemen die ontstaan kunnen worden opgelost zonder contact op te nemen met een erkend servicecentrum. Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing De resterende duur in het display wordt verlengd en schakelt bijna naar het eind van de programmaduur. • Dit is geen storing. Het apparaat werkt goed. Weinig lekkage uit de deur van het apparaat. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • De deur van het apparaat is niet gecentreerd op de kuip. Verstel de achterpoot (indien van toepassing). De deur van het apparaat sluit moeilijk.
NEDERLANDS 21 Probleem Mogelijke oorzaak en oplossing Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan. • Het glansmiddel is op of de dosering van glansmiddel is niet voldoende. Stel de dosering van het glansmiddel in op een hogere stand. • Plastic voorwerpen moeten mogelijk met een doek worden afgedroogd. • Activeer voor de beste droogprestatie de optie XtraDry. • We raden aan altijd glansmiddel te gebruiken, zelfs in combinatie met wastabletten.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water. middeldoseerbakje. • Het water kan het vaatwasmiddel niet uit het vaatwasmiddeldoseerbakje spoelen. Zorg ervoor dat de bovenste sproeiarm niet geblokkeerd of verstopt is.
NEDERLANDS 23 14. MILIEUBESCHERMING Recycle de materialen met het symbool . Gooi de verpakking in een geschikte verzamelcontainer om het te recyclen. Help om het milieu en de volksgezondheid te beschermen en recycle het afval van elektrische en elektronische apparaten. Gooi apparaten gemarkeerd met het symbool niet weg met het huishoudelijk afval. Breng het product naar het milieustation bij u in de buurt of neem contact op met de gemeente.
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ............................................................................ 25 2. CONSIGNES DE SÉCURITÉ................................................................................... 26 3. DESCRIPTION DE L'APPAREIL.............................................................................. 28 4. BANDEAU DE COMMANDE................................................................................. 29 5. PROGRAMMES............................
FRANÇAIS 1. 25 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 29 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Programme (haut) Touche Programme (bas) 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche XtraDry Touche RESET Voyants 4.1 Voyants Indicateur Description Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.com Programme Degré de salissure Type de vaisselle P4 • Vaisselle fraîche- • Lavage à 60 °C ment salie • Rinçages • Vaisselle et couverts 4) P5 • Tous Phases du programme Options • XtraDry • Prélavage 5) 1) Ce programme vous permet d'optimiser votre consommation d'eau et d'énergie pour la vaisselle et les couverts normalement sales. (Il s'agit du programme standard pour les instituts de tests.) 2) L'appareil détecte le degré de salissure et la quantité de vaisselle dans les paniers.
FRANÇAIS 5.2 Informations pour les instituts de test Pour toute information relative aux performances de test, envoyez un courrier électronique à l'adresse : 31 info.test@dishwasher-production.com Notez le numéro du produit (PNC) indiqué sur la plaque signalétique. 6. RÉGLAGES 6.1 Mode Programmation et mode Utilisateur Lorsque l'appareil est en mode Programmation, il est possible de sélectionner un programme et d'entrer en mode Utilisateur.
www.aeg.com Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 15 - 18 26 - 32 2,6 - 3,2 18 - 22 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 3 4 - 10 7 - 18 0,7 - 1,8 5 - 12 2 <4 <7 <0,7 <5 1 2) 1) Réglages d'usine. 2) N'utilisez pas de sel à ce niveau.
FRANÇAIS – Les niveaux de liquide de rinçage s'échelonnent de 0A à 6A. – Niveau 0 = aucun liquide de rinçage n'est libéré. 3. Appuyez sur la touche à plusieurs reprises pour modifier le réglage. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.4 Notification de liquide de rinçage vide Quand la chambre du liquide de rinçage est vide, le voyant de liquide de rinçage s'allume pour signaler qu'un remplissage du liquide de rinçage est nécessaire.
www.aeg.com 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver d'options pendant le déroulement d'un programme. Certaines options ne sont pas compatibles entre elles. Si vous avez choisi des options incompatibles, l'appareil en désactivera automatiquement une ou plusieurs. Seuls les voyants correspondant aux options encore actives resteront allumés. 7.
FRANÇAIS 8.1 Réservoir de sel régénérant ATTENTION! Utilisez uniquement du sel régénérant conçu pour les lave-vaisselle. Le sel permet de recharger la résine dans l'adoucisseur d'eau et de garantir de bons résultats de lavage en utilisation quotidienne. Remplissage du réservoir de sel régénérant 35 De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion. Afin d'éviter cela, après avoir rempli le réservoir de sel régénérant, démarrez un programme.
www.aeg.com Si vous utilisez des pastilles de détergent multifonctions et que les performances du séchage sont satisfaisantes, l'indication de remplissage du liquide de rinçage peut être désactivée. Pour de meilleures performances de séchage, nous vous recommandons de toujours utiliser du liquide de rinçage, même si vous utilisez déjà des pastilles tout-en-1 contenant un agent de rinçage. 9. UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2.
FRANÇAIS Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3. Appuyez à plusieurs reprises sur la touche ou jusqu'à ce que l'affichage indique le numéro du programme que vous souhaitez lancer. Le numéro du programme s'affiche pendant environ 3 secondes, puis la durée du programme s'affiche. 4. Sélectionnez les options compatibles. 5.
www.aeg.com • • • • programme avec une phase de prélavage. Utilisez toujours tout l'espace des paniers. Lorsque vous chargez l'appareil, veillez à ce que l'eau libérée par les embouts des bras d'aspersion puisse atteindre parfaitement les plats pour qu'ils soient parfaitement lavés. Vérifiez que les plats ne se touchent pas ou ne se recouvrent pas les uns les autres. Vous pouvez utiliser du détergent, du liquide de rinçage et du sel régénérant séparément, ou des pastilles tout en 1 (par ex.
FRANÇAIS • Vérifiez que les verres ne se touchent pas pour éviter qu'ils ne se brisent. • Placez les petits articles dans le panier à couverts. • Placez les objets légers dans le panier supérieur. Disposez-les de façon à ce qu'ils ne puissent pas se retourner. • Assurez-vous que les bras d'aspersion tournent librement avant de lancer un programme. 10.5 Avant le démarrage d'un programme Assurez-vous que : • Les filtres sont propres et correctement installés.
www.aeg.com 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur Nous vous conseillons de nettoyer régulièrement le bras d'aspersion supérieur afin d'éviter que ses orifices ne se bouchent.
FRANÇAIS toutes les particules de saleté incrustées dans les orifices. 41 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur 4.
www.aeg.com Problème et code d'alarme Cause et solution possibles Vous ne pouvez pas faire fonctionner l'appareil. • Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. • Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles. Le programme ne démarre pas. • Vérifiez que la porte de l'appareil est fermée. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte.
FRANÇAIS 43 Problème et code d'alarme Cause et solution possibles Petite fuite au niveau de la porte de l'appareil. • L'appareil n'est pas de niveau. Desserrez ou serrez les pieds réglables (si disponibles). • La porte de l'appareil n'est pas centrée avec la cuve. Réglez le pied arrière (si disponible). La porte de l'appareil est difficile à fermer. • L'appareil n'est pas de niveau. Desserrez ou serrez les pieds réglables (si disponibles). • De la vaisselle dépasse des paniers.
www.aeg.com Problème Cause et solution possibles Résultats de séchage insatisfaisants. • La vaisselle est restée trop longtemps à l'intérieur de l'appareil, porte fermée. • Il n'y a pas de liquide de rinçage ou le dosage du liquide de rinçage n'est pas suffisant. Augmentez le niveau de distributeur de liquide de rinçage. • Les articles en plastiques peuvent avoir besoin d'être essuyés. • Pour de meilleurs performances de séchage, activez l'option XtraDry.
FRANÇAIS 45 Problème Cause et solution possibles Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble. Évitez de placer les couverts en argent et en acier inoxydable les uns à côté des autres.
www.aeg.com Capacité Couverts 15 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour les autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple, panneaux solaires ou énergie éolienne), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 14.
DEUTSCH 47 INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE.........................................................................................48 2. SICHERHEITSANWEISUNGEN.............................................................................. 49 3. GERÄTEBESCHREIBUNG.......................................................................................51 4. BEDIENFELD........................................................................................................... 52 5. PROGRAMME............
1. www.aeg.com SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
DEUTSCH • • • • • • • • 49 Beachten Sie, dass die Höchstzahl an Maßgedecken 15 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. Stellen Sie Messer und Besteck mit scharfen Spitzen mit der Spitze nach unten in den Besteckkorb oder legen Sie sie waagerecht in das Gerät.
www.aeg.com • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist.
DEUTSCH 3. GERÄTEBESCHREIBUNG 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Oberster Sprüharm Oberer Sprüharm Unterer Sprüharm Filter Typenschild Salzbehälter Lüftungsschlitze 3.1 Beam-on-Floor Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Küchenboden projiziert wird. • Nach dem Start des Programms leuchtet der rote Lichtstrahl auf und bleibt während der gesamten Programmdauer eingeschaltet.
www.aeg.com 4. BEDIENFELD 1 1 2 3 4 5 2 3 Taste „Ein/Aus“ Display Taste Delay Programmtaste (nach oben) Programmtaste (nach unten) 4 6 7 8 9 5 6 7 8 9 Taste TimeSaver Taste XtraDry Taste RESET Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Programmende. Kontrolllampe Salz. Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs. 5.
DEUTSCH Programm Verschmutzungsgrad Beladung Programmphasen Optionen P4 • Vor kurzem benutztes Geschirr • Geschirr und Besteck • Hauptspülgang 60 °C • Spülgänge • XtraDry • Alle • Vorspülen 4) P5 53 5) 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. (Dies ist das Standardprogramm für Prüfinstitute.) 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Körben.
www.aeg.com 5.2 Informationen für Prüfinstitute info.test@dishwasher-production.com Möchten Sie Informationen zum Leistungstest erhalten, schicken Sie eine E-Mail an: Notieren Sie die Produktnummer (PNC), die Sie auf dem Typenschild finden. 6. EINSTELLUNGEN 6.1 Programmwahlmodus und Benutzermodus Wenn sich das Gerät im Programmwahlmodus befindet, kann ein Programm eingestellt und der Benutzermodus aufgerufen werden.
DEUTSCH Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH) mmol/l 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 55 Clarke Was- Einstellung für den serhärteWasserenthärter grade 1) Werkseitige Einstellung. 2) Verwenden Sie kein Salz bei diesen Werten.
www.aeg.com – Die Klarspülmittelstufen reichen von 0A bis 6A. – Stufe 0 = Es wird kein Klarspülmittel zugegeben. Klarspülmittel-Dosierer ist eingeschaltet (Werkseinstellung). 3. Drücken Sie Einstellung. zum Ändern der 3. Drücken Sie wiederholt, um die Einstellung zu ändern. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. = der Klarspülmittel-Dosierer ist ausgeschaltet. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 6.4 Klarspülnachfüllanzeige 6.
DEUTSCH 57 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten. Es ist nicht möglich, Optionen während eines laufenden Programms einoder auszuschalten. Nicht alle Optionen lassen sich miteinander kombinieren. Wenn Sie Optionen einschaltet haben, die nicht miteinander kombinierbar sind, schaltet das Gerät automatisch eine oder mehrere von ihnen aus. Es leuchten dann nur die Anzeigen der noch eingeschalteten Optionen. 7.
www.aeg.com 8.1 Salzbehälter VORSICHT! Verwenden Sie nur Spezialsalz für Geschirrspüler. 8.2 Füllen des KlarspülmittelDosierers A B Das Salz wird für die Regenerierung des Filterharzes im Wasserenthärter und zur Erzielung guter Spülergebnisse im täglichen Gebrauch benötigt. So füllen Sie den Salzbehälter: 1. Drehen Sie den Deckel des Salzbehälters gegen den Uhrzeigersinn und entfernen Sie ihn. 2. Füllen Sie 1 Liter Wasser in den Salzbehälter (nur beim ersten Mal). 3.
DEUTSCH 59 Wenn Sie MultiReinigungstabletten verwenden und die Trocknungsleistung zufriedenstellend ist, kann die Klarspülernachfüllanzeige ausgeschaltet werden. Für eine bessere Trocknungsleistung empfehlen wir stets Klarspülmittel zu verwenden, auch wenn Sie MultiReinigungstabletten benutzen, die Klarspülmittel enthalten. 9. TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten.
www.aeg.com Starten eines Programms 1. Lassen Sie die Gerätetür einen Spaltbreit offen. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. 3. Drücken Sie wiederholt oder , bis im Display die Nummer des gewünschten Programms erscheint. Die Programmnummer wird etwa 3 Sekunden lang im Display angezeigt, anschließend erscheint die Programmdauer. 4. Stellen Sie die verfügbaren Optionen ein. 5.
DEUTSCH • • • • verfügbar) oder wählen Sie ein Programm mit Vorspülgang. Nutzen Sie die Körbe immer ganz aus. Wenn Sie das Gerät beladen, achten Sie darauf, dass das Geschirr komplett von dem Wasser aus den Sprüharmdüsen erreicht und gespült wird. Achten Sie darauf, dass das Geschirr sich weder berührt noch von anderem Geschirr verdeckt wird. Sie können Geschirrspülreiniger, Klarspüler und Salz separat oder Kombi-Reinigungstabletten (z.B. „3in1“, „4in1“, „All-in-1“) verwenden.
www.aeg.com • Vergewissern Sie sich, dass sich die Sprüharme ungehindert bewegen können, bevor Sie ein Programm starten. • Das Programm eignet sich für die Beladung und den Verschmutzungsgrad. • Die Reinigungsmittelmenge stimmt. 10.5 Vor dem Starten eines Programms 10.6 Entladen der Körbe Kontrollieren Sie folgende Punkte: • Die Filter sind sauber und ordnungsgemäß eingesetzt. • Der Deckel des Salzbehälters ist fest geschlossen. • Die Sprüharme sind nicht verstopft.
DEUTSCH 63 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein.
www.aeg.com 11.3 Reinigen der Außenseiten • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger. • Benutzen Sie keine Scheuermittel, scheuernde Reinigungsschwämmchen oder Lösungsmittel. 3. Reinigen Sie den Sprüharm unter fließendem Wasser. Entfernen Sie Verunreinigungen aus den Öffnungen des Sprüharms mit einem spitzen Gegenstand, z.B. einem Zahnstocher. 11.
DEUTSCH Störung anhand der in der Tabelle enthaltenen Hinweise selbst beheben können. WARNUNG! Nicht ordnungsgemäße Reparaturen stellen ein Sicherheitsrisiko für den Benutzer dar. Die Reparaturarbeiten dürfen nur von qualifiziertem Personal durchgeführt werden. 65 Bei manchen Störungen zeigt das Display einen Alarmcode an. Die meisten Störungen, die auftreten, können behoben werden, ohne dass der autorisierte Kundendienst gerufen werden muss.
www.aeg.com Problem und Alarmcode Mögliche Ursachen und Abhilfe Während des Betriebs stoppt das Gerät und läuft wieder an (mehrmals). • Das ist normal. So werden optimale Reinigungsergebnisse erzielt und Strom gespart. Das Programm dauert zu lang. • Wählen Sie die TimeSaver-Option, um die Programmdauer zu verkürzen. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie diese ab oder warten Sie, bis sie abgelaufen ist.
DEUTSCH 67 12.1 Die Spül- und Trocknungsergebnisse sind nicht zufriedenstellend Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Spülergebnisse. • Siehe „Täglicher Gebrauch“, „Tipps und Hinweise“ sowie die Broschüre zum Beladen der Körbe. • Nutzen Sie intensivere Spülprogramme. • Reinigen Sie die Austrittsdüsen der Sprüharme und die Siebe. Siehe Kapitel „Reinigung und Pflege“. Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät.
www.aeg.com Störung Mögliche Ursache und Abhilfe Rostspuren am Besteck. • Das Spülwasser enthält zu viel Salz. Siehe „Wasserenthärter“. • Silber- und Edelstahlbesteck wurden zusammen eingeordnet. Ordnen Sie nicht Silber- und Edelstahlbesteck zusammen ein. Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen.
DEUTSCH Leistungsaufnahme Ein-Zustand (W) 5.0 Leistungsaufnahme Aus-Zustand (W) 0.10 69 1) Weitere Angaben finden Sie auf dem Typenschild. 2) Wenn Sie Heißwasser mit umweltfreundlichen, alternativen Energiequellen (z. B. Solaranlagen oder Windkraft) aufbereiten, können Sie durch den Anschluss des Geräts an die Heißwasserversorgung Energie sparen. 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern.
www.aeg.
DEUTSCH 71
117902663-A-302016 www.aeg.