NL FR DE Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle Benutzerinformation Geschirrspüler 2 22 43 FAVORIT56302UM0
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Aan/uit-toets Programma-indicatielampjes Indicatielampjes Weergave Delay-toets ExtraHygiene-toets 7 8 9 10 Multitab-toets Programmakeuzetoets (omhoog) Programmakeuzetoets (omlaag) Reset-toets 4.1 Indicatielampjes Aanduiding Beschrijving Multitab-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje.
www.aeg.com 5.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) 13 - 15 1.5 - 1.6 150 - 170 13 - 14 0.7 - 0.9 70 - 80 9 0.8 30 4 0.1 14 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten info.test@dishwasher-production.com Schrijf het productnummer (PNC) op dat u op het typeplaatje vindt.
www.aeg.com Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Fabrieksinstelling. 2) Gebruik geen zout op dit niveau.
NEDERLANDS • Het indicatielampje blijft knipperen. • Het display toont de huidige instelling: = Glansmiddeldosering geactiveerd. 3. Druk op 11 om de instelling te wijzigen. = Glansmiddeldosering gedeactiveerd. Het lampje glansmiddel gaat uit. 4. Druk op de knop aan/uit om de instelling te bevestigen. 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd. De opties kunnen niet worden in- of uitgeschakeld als een programma in werking is. 7.
www.aeg.com 8.1 Het zoutreservoir LET OP! Gebruik uitsluitend zout dat specifiek is bedoeld voor gebruik in vaatwassers. 8.2 Het vullen van het glansmiddeldoseerbakje A D B Het zout wordt gebruikt om de hars in de waterontharder te herladen en voor goede wasresultaten voor dagelijks gebruik. Het zoutreservoir vullen: 1. Draai de dop linksom om het zoutreservoir te openen. 2. Doe 1 liter water in het zoutreservoir (alleen de eerste keer). 3. Vul het zoutreservoir met regenereerzout.
NEDERLANDS 13 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de keuzemodus Programma staat. • Vul het zoutreservoir als het zoutindicatielampje brandt. • Vul het glansmiddeldoseerbakje als het indicatielampje van het glansmiddel brandt. 3. Ruim de korven in. 4. Voeg vaatwasmiddel toe. Activeer de optie Multitab als u multitabletten gebruikt. 5.
www.aeg.com Een programma starten met een uitgestelde start De uitgestelde start annuleren tijdens het aftellen 1. Stel een programma in. 2. Blijf op Delay drukken tot het display de uitgestelde tijd toont die u wilt instellen (van 1 tot 24 uur). Het indicatielampje van het geselecteerde programma blijft knipperen. 3. Sluit de deur van het apparaat om het aftellen te starten. Het programma-indicatielampje stopt met knipperen en gaat branden.
NEDERLANDS 15 10.2 Gebruik van zout, glansmiddel en vaatwasmiddel 6. Schakel het glansmiddeldoseerbakje in. • Gebruik enkel zout, glansmiddel en vaatwasmiddel voor afwasautomaten. Overige producten kunnen het apparaat beschadigen. • Multitabletten zijn doorgaans geschikt voor een waterhardheid tot 21 °dH. Bij een hogere waterhardheid moet zout, glansmiddel en vaatwasmiddel worden gebruikt naast het gebruik van multitabletten.
www.aeg.com 10.6 De rekken uitruimen Aan het einde van het programma kan er water aan de zijkanten en de deur van het apparaat achterblijven. 1. Laat de borden afkoelen voordat u deze uit het apparaat neemt Hete borden zijn gevoelig voor beschadigingen. 2. Ruim eerst het onderrek en dan het bovenrek uit 11. ONDERHOUD EN REINIGING WAARSCHUWING! Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht.
NEDERLANDS 17 openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit.
www.aeg.com Het merendeel van de problemen die ontstaan kunnen worden opgelost zonder contact op te nemen met een erkend servicecentrum. Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren. • Zorg dat de stekker in het stopcontact zit. • Zorg dat er geen zekering in de zekeringenkast is doorgebrand. Het programma begint niet. • Zorg dat de deur van het apparaat is gesloten.
NEDERLANDS 19 Probleem en alarmcode Mogelijke oorzaak en oplossing De deur van het apparaat sluit moeilijk. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • Delen van het serviesgoed steken uit de korven. Ratelende / kloppende geluiden vanuit het apparaat. • Het serviesgoed is niet juist in de korven gerangschikt. Raadpleeg de folder voor het laden van de korven. • Zorg ervoor dat de sproeiarmen vrij kunnen ronddraaien. Het apparaat maakt kortsluiting.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Vlekken en opgedroogde watervlekken op glazen en servies. • De vrijgegeven hoeveelheid glansmiddel is te laag. Zet de dosering van het glansmiddel op een hogere stand. • De kwaliteit van het glansmiddel kan de oorzaak zijn. Het serviesgoed is nat. • Het programma heeft geen droogfase of heeft een droogfase met lage temperatuur. • Het glansmiddeldoseerbakje is leeg. • De kwaliteit van het glansmiddel kan de oorzaak zijn.
NEDERLANDS 21 Raadpleeg "Voor het eerste gebruik", "Dagelijks gebruik" of "Aanwijzingen en tips" voor mogelijke andere oorzaken. 13. TECHNISCHE INFORMATIE Afmetingen Breedte / hoogte / diepte (mm) 596 / 818 - 898 / 575 Elektrische aansluiting 1) Voltage (V) 220 - 240 Frequentie (Hz) 50 Watertoevoerdruk Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 13 Energieverbruik Modus aan laten (W) 0.
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 23 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 24 3. DESCRIPTION DE L'APPAREIL.............................................................................. 26 4. BANDEAU DE COMMANDE................................................................................. 27 5. PROGRAMMES..........................
FRANÇAIS 1. 23 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3.
FRANÇAIS 27 4. BANDEAU DE COMMANDE 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Touche Marche/Arrêt Voyants de programme Voyants Affichage Touche Delay Touche ExtraHygiene 7 8 9 10 Touche Multitab Touche Programme (haut) Touche Programme (bas) Touche Reset 4.1 Voyants Indicateur Description Voyant Multitab. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage.
www.aeg.com 5.
FRANÇAIS Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 7 - 12 0.6 - 1.4 40 - 150 13 - 15 1.5 - 1.6 150 - 170 13 - 14 0.7 - 0.9 70 - 80 9 0.8 30 4 0.1 14 29 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.
FRANÇAIS Utilisation du liquide de rinçage et des pastilles touten-un Lorsque vous activez l'option Multitab, le distributeur de liquide de rinçage continue à libérer le liquide de rinçage. Vous pouvez cependant désactiver le distributeur de liquide de rinçage. Dans ce cas, les résultats de séchage risquent d'être insatisfaisants. Lorsque le distributeur de liquide de rinçage est désactivé, le voyant de contrôle du liquide de rinçage est toujours éteint.
www.aeg.com 8. AVANT LA PREMIÈRE UTILISATION 1. Assurez-vous que le réglage actuel de l'adoucisseur d'eau est compatible avec la dureté de l'arrivée d'eau. Si ce n'est pas le cas, réglez le niveau de l'adoucisseur d'eau. 2. Remplissez le réservoir de sel régénérant. 3. Remplissez le distributeur de liquide de rinçage. 4. Ouvrez le robinet d'eau. 5. Lancez un programme pour éliminer tous les résidus qui peuvent toujours se trouver à l'intérieur de l'appareil.
FRANÇAIS 8.2 Comment remplir le distributeur de liquide de rinçage A D ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. B C B A 1. Appuyez sur le bouton d'ouverture (D) pour ouvrir le couvercle (C). 2. Versez le liquide de rinçage dans le distributeur (A) jusqu'à ce qu'il atteigne le niveau « max ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle.
www.aeg.com A 30 B D 20 C 1. Appuyez sur le bouton d'ouverture (B) pour ouvrir le couvercle (C). 2. Versez le produit de lavage, en poudre ou en tablette, dans le compartiment (A). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage dans le compartiment (D). 4. Fermez le couvercle. Assurez-vous que le bouton d'ouverture se verrouille correctement. 9.
FRANÇAIS Annulation du départ différé au cours du décompte démarrer un nouveau programme de lavage. Lorsque vous annulez le départ différé, vous devez régler de nouveau le programme et les options. Fin du programme Appuyez sur Reset jusqu'à ce que l'appareil soit en mode de sélection du programme. Annulation du programme Maintenez la touche Reset enfoncée jusqu'à ce que l'appareil passe en mode Programmation.
www.aeg.com améliore les résultats de lavage et de séchage avec l'utilisation de pastilles tout en 1. • Les tablettes de détergent ne se dissolvent pas complètement durant les programmes courts. Pour éviter que des résidus de produit de lavage ne se déposent sur la vaisselle, nous recommandons d'utiliser des pastilles de détergent avec des programmes longs. • N'utilisez que la quantité nécessaire de produit de lavage. Reportez-vous aux instructions figurant sur l'emballage du produit de lavage. 10.
FRANÇAIS 37 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur. Les filtres sales et les bras d'aspersion obstrués diminuent les résultats de lavage. Contrôlez-les régulièrement et nettoyezles si nécessaire. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. 11.1 Nettoyage des filtres Le système de filtres est composé de 3 parties. C B A 5.
www.aeg.com • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu.
FRANÇAIS 39 Problème et code d'alarme Cause et solution possibles Vous ne pouvez pas faire fonctionner l'appareil. • Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. • Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles. Le programme ne démarre pas. • Vérifiez que la porte de l'appareil est fermée. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte.
www.aeg.com Problème et code d'alarme Cause et solution possibles La porte de l'appareil est difficile à fermer. • L'appareil n'est pas de niveau. Desserrez ou serrez les pieds réglables (si disponibles). • De la vaisselle dépasse des paniers. Bruit de cliquetis ou de battement à l'intérieur de l'appareil. • La vaisselle n'est pas correctement rangée dans les paniers. Reportez-vous au manuel de chargement du panier. • Assurez-vous que les bras d'aspersion peuvent tourner librement.
FRANÇAIS 41 Problème Cause et solution possibles Il y a des traînées blanchâtres ou pellicules bleuâtres sur les verres et la vaisselle. • La quantité de liquide de rinçage libérée est trop importante. Réglez le niveau de dosage du liquide de rinçage sur une valeur plus faible. • La quantité de produit de lavage est excessive. Il y a des taches et traces de gouttes d'eau séchées sur les verres et la vaisselle. • La quantité de liquide de rinçage libérée n'est pas suffisante.
www.aeg.com Problème Cause et solution possibles Dépôts calcaires sur la vaisselle, dans la cuve et à l'intérieur de la porte. • Reportez-vous au chapitre « Adoucisseur d'eau ». Vaisselle ternie, décolorée ou ébréchée. • Assurez-vous de ne placer dans l'appareil que des articles adaptés au lave-vaisselle. • Chargez et déchargez le panier avec précautions. Reportez-vous au manuel de chargement du panier. • Placez les objets délicats dans le panier supérieur.
DEUTSCH 43 INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.......................................................................... 44 2. SICHERHEITSANWEISUNGEN.............................................................................. 45 3. GERÄTEBESCHREIBUNG.......................................................................................47 4. BEDIENFELD........................................................................................................... 48 5. PROGRAMME.....................
1. www.aeg.com SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
DEUTSCH • • • • • • • • 45 Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. Stellen Sie Messer und Besteck mit scharfen Spitzen mit der Spitze nach unten in den Besteckkorb oder legen Sie sie waagerecht in das Gerät.
www.aeg.com • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist.
DEUTSCH • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in dem Gerät einschließen. 3.
www.aeg.com 4. BEDIENFELD 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Taste „Ein/Aus“ Programmkontrolllampen Kontrolllampen Display Taste Delay Taste ExtraHygiene 7 8 9 10 Taste Multitab Programmtaste (nach oben) Programmtaste (nach unten) Taste Reset 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Multitab. Kontrolllampe Salz. Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs. Kontrolllampe Delay. Kontrolllampe ExtraHygiene.
DEUTSCH 49 5.
www.aeg.com 5.1 Verbrauchswerte Programm 1) Wasser (l) Energieverbrauch (kWh) Dauer (Min.) 11 1.050 195 7 - 12 0.6 - 1.4 40 - 150 13 - 15 1.5 - 1.6 150 - 170 13 - 14 0.7 - 0.9 70 - 80 9 0.8 30 4 0.1 14 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Möchten Sie Informationen zum Leistungstest erhalten, schicken Sie eine E-Mail an: info.
DEUTSCH 51 Wasserhärte Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH) mmol/l Clarke Was- Einstellung für den serhärteWasserenthärter grade 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.
www.aeg.com jedoch ausschalten. In diesem Fall sind die Trockenergebnisse möglicherweise nicht zufriedenstellend. Ist der Klarspülmittel-Dosierer ausgeschaltet, leuchtet die entsprechende Kontrolllampe nie. . • Die Kontrolllampen erlöschen. und blinkt • Die Kontrolllampe weiter. • Im Display wird die aktuelle Ausschalten des KlarspülmittelDosierers Das Gerät muss sich im Programmwahlmodus befinden. Einstellung angezeigt: Klarspülmittel-Dosierer eingeschaltet. 3. Drücken Sie 1.
DEUTSCH in Ihrem Gebiet entspricht. Wenn nicht, stellen Sie die Wasserenthärterstufe ein. 2. Füllen Sie den Salzbehälter. 3. Füllen Sie den KlarspülmittelDosierer. 4. Öffnen Sie den Wasserhahn. 5. Starten Sie ein Programm, um Fertigungsrückstände, die sich möglicherweise noch im Gerät befinden können, zu beseitigen. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. Wenn Sie ein Programm starten, kann es bis zu 5 Minuten dauern das Filterharz des Wasserenthärters zu regenerieren.
www.aeg.com ACHTUNG! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. Tuch auf, um zu große Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet. 1. Drücken Sie die Entriegelungstaste (D), um den Deckel (C) zu öffnen. 2. Füllen Sie den KlarspülmittelDosierer (A) bis zur Markierung „max“. 3.
DEUTSCH 55 • Nach 5 Minuten, wenn das Programm nicht gestartet wurde. Öffnen der Tür während eines laufenden Programms Starten eines Programms Wenn Sie die Tür während eines laufenden Programms öffnen, stoppt das Gerät. Dies kann sich auf den Energieverbrauch und die Programmdauer auswirken. Wenn Sie die Tür wieder schließen, läuft das Programm ab dem Zeitpunkt der Unterbrechung weiter. 1. Lassen Sie die Gerätetür einen Spaltbreit offen. 2. Drücken Sie die Taste „Ein/Aus“, um das Gerät einzuschalten.
www.aeg.com 10. TIPPS UND HINWEISE 10.1 Allgemeines Die folgenden Hinweise stellen optimale Reinigungs- und Trocknungsergebnisse im täglichen Gebrauch sicher, und tragen auch zum Umweltschutz bei. • Schütten Sie größere Lebensmittelreste auf dem Geschirr in den Abfallbehälter. • Spülen Sie das Geschirr nicht von Hand vor. Verwenden Sie bei Bedarf das Vorspülprogramm (wenn verfügbar) oder wählen Sie ein Programm mit Vorspülgang. • Nutzen Sie die Körbe immer ganz aus.
DEUTSCH 10.4 Beladen der Körbe • Spülen Sie im Gerät nur spülmaschinenfestes Geschirr. • Spülen Sie im Gerät keine Geschirrteile aus Holz, Horn, Aluminium, Zinn oder Kupfer. • Spülen Sie in diesem Gerät keine Gegenstände, die Wasser aufnehmen können (Schwämme, Geschirrtücher usw.). • Entfernen Sie Speisereste vom Geschirr. • Weichen Sie eingebrannte Essensreste ein. • Ordnen Sie hohle Gefäße (z. B. Tassen, Gläser, Pfannen) mit der Öffnung nach unten ein.
www.aeg.com 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. 4. Reinigen Sie die Filter. ACHTUNG! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus.
DEUTSCH 11.4 Reinigung des Geräteinnenraums • Reinigen Sie das Gerät und die Gummidichtung der Tür sorgfältig mit einem weichen, feuchten Tuch. • Wenn Sie regelmäßig Kurzprogramme verwenden, können diese zu Fett- und Kalkablagerungen im Gerät führen. Um dieses zu vermeiden, wird empfohlen, 59 mindestens zweimal im Monat Programme mit langer Laufzeit zu verwenden.
www.aeg.com Problem und Alarmcode Mögliche Ursachen und Abhilfe Es läuft kein Wasser in das Gerät. • Vergewissern Sie sich, dass der Wasserzulauf geöffnet ist. • Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Information erhalten Sie von Ihrem Wasserversorger. • Vergewissern Sie sich, dass der Wasserzulauf nicht verstopft ist. • Vergewissern Sie sich, dass der Filter im Zulaufschlauch nicht verstopft ist.
DEUTSCH Problem und Alarmcode 61 Mögliche Ursachen und Abhilfe Das Gerät löst die Sicherung • Die abgesicherte Stromstärke reicht nicht für den gleichaus. zeitigen Betrieb aller eingeschalteten Geräte. Überprüfen Sie, für welche Stromstärke die Steckdose bzw. der Stromzähler zugelassen ist, und schalten Sie eines der eingeschalteten Geräte aus. • Ein Fehler in der Elektrik des Geräts. Wenden Sie sich an den autorisierten Kundendienst.
www.aeg.com Störung Mögliche Ursachen und Abhilfe Das Geschirr ist nass. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur. • Der Klarspülmittel-Dosierer ist leer. • Die Ursache kann in der Qualität des Klarspülmittels liegen. • Die Ursache kann in der Qualität der Multi-Reinigungstabletten liegen. Probieren Sie eine andere Marke aus oder schalten Sie den Klarspülmittel-Dosierer ein und verwenden Sie ihn zusammen mit den Multi-Reinigungstabletten.
DEUTSCH 63 Siehe „Vor der ersten Inbetriebnahme“, „Täglicher Gebrauch“ oder „Tipps und Hinweise“ bezüglich anderer möglicher Ursachen. 13. TECHNISCHE DATEN Abmessungen Breite/Höhe/Tiefe (mm) 596 / 818 - 898 / 575 Elektrischer Anschluss 1) Spannung (V) 220 - 240 Frequenz (Hz) 50 Wasserdruck Min./max. bar (MPa) 0.5 (0.05) / 8 (0.8) Wasserversorgung Kalt- oder Warmwasser 2) max. 60 °C Fassungsvermögen Maßgedecke 13 Leistungsaufnahme Ein-Zustand (W) 0.
100003371-A-222015 www.aeg.