CS NL FR Návod k použití Myčka nádobí Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle 2 22 43 FAVORIT 56302MO FAVORIT 56302WO
www.aeg.com OBSAH 1. BEZPEČNOSTNÍ INFORMACE......................................................................... 3 2. BEZPEČNOSTNÍ POKYNY................................................................................4 3. POPIS SPOTŘEBIČE.........................................................................................6 4. OVLÁDACÍ PANEL ............................................................................................7 5. PROGRAMY....................................................
ČESKY 1. 3 BEZPEČNOSTNÍ INFORMACE Tento návod si pečlivě přečtěte ještě před instalací spotřebiče a jeho prvním použitím. Výrobce nezodpovídá za škody a zranění způsobená nesprávnou instalací či chybným používáním. Návod k použití vždy uchovávejte spolu se spotřebičem pro jeho budoucí použití. 1.
www.aeg.com • • • • • • • Jestliže je poškozený přívodní kabel, smí ho vyměnit pouze výrobce, autorizované servisní středisko nebo osoba s podobnou příslušnou kvalifikací, jinak by mohlo dojít k úrazu. Nože a další nástroje s ostrými špičkami vkládejte do košíčku na příbory špičkou dolů nebo vodorovně. Nenechávejte dvířka spotřebiče otevřená bez dozoru, aby na ně nikdo nespadl. Před čištěním nebo údržbou spotřebič vždy vypněte a vytáhněte síťovou zástrčku ze zásuvky.
ČESKY • • dlouho používané, nechte vodu na několik minut odtéct, dokud nebude čistá. Při prvním použití spotřebiče se ujistěte, že nedochází k únikům vody. Přívodní hadice s opláštěním je vybavena bezpečnostním ventilem a vnitřním síťovým kabelem. • • • 5 Nádobí ze spotřebiče nevyjímejte, dokud se nedokončí program. Na nádobí mohou být zbytky mycího prostředku. Pokud během probíhajícího programu otevřete dvířka spotřebiče, může dojít k uvolnění horké páry.
www.aeg.com 3.
ČESKY 4. OVLÁDACÍ PANEL 1 2 8 1 2 3 4 5 Tlačítko Zap/Vyp Tlačítko Program Kontrolky programů Displej Tlačítko Delay 3 4 7 5 6 6 Tlačítko Start 7 Kontrolky 8 Tlačítko Option 4.1 Kontrolky Kontrolka Popis Fáze mytí. Rozsvítí se během fáze mytí. Fáze sušení. Rozsvítí se během fáze sušení. Kontrolka Multitab. Kontrolka množství soli. Nikdy v průběhu programu nesvítí. Kontrolka stavu leštidla. Nikdy v průběhu programu nesvítí. Kontrolka ÖKO PLUS.
www.aeg.com 5.
ČESKY Program 1) Voda (l) Energie (kWh) Délka (min) 8-9 1.1 - 1.3 55 - 65 9 0.8 30 4 0.1 14 9 1) Hodnoty se mohou měnit v závislosti na tlaku a teplotě vody, na kolísání v dodávce proudu, na zvole‐ ných funkcích a na množství nádobí. 5.2 Informace pro zkušebny Pro všechny potřebné informace ohledně testu výkonnosti zašlete e-mail na: Poznamenejte si výrobní číslo (PNC) uvedené na typovém štítku. info.test@dishwasher-production.com 6. NASTAVENÍ 6.
www.aeg.com Německé stupně (°dH) Francouzské stupně (°fH) mmol/l Clarkovy stupně Nastavení změkčo‐ vače vody 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Nastavení z výroby.
ČESKY kontrolky , s prázdným displejem. 2. Stiskněte Option. a • Kontrolky zhasnou. • • Kontrolka dále bliká. Na displeji se zobrazí aktuální nastavení. – a = dávkovač leštidla je zapnutý. = dávkovač leštidla je vypnutý. 3. Stisknutím Option změňte nastavení. 4. Potvrďte nastavení stisknutím tlačítka Zap/Vyp. – 6.4 Zvuková signalizace Zvuková signalizace zazní, když dojde k poruše spotřebiče. Tyto zvukové signály nelze vypnout. Další zvuková signalizace se také spustí po dokončení programu.
www.aeg.com Jak zapnout ÖKO PLUS Stiskněte Option dokud se nerozsvítí . kontrolka Pokud tuto funkci nelze s daným programem použít, příslušná kontrolka se nerozsvítí nebo bude několik sekund rychle blikat a poté zhasne. Na displeji se zobrazí aktualizovaná délka programu. 8. PŘED PRVNÍM POUŽITÍM 1. Ujistěte se, zda aktuální stupeň změkčovače vody odpovídá tvrdosti vaší vody. Pokud ne, nastavte stupeň změkčovače vody. 2. Naplňte zásobník na sůl. 3. Naplňte dávkovač leštidla. 4.
ČESKY 8.2 Jak plnit dávkovač leštidla A D POZOR! Používejte pouze leštidlo pro myčky nádobí. B C Voličem můžete nastavit dávkované množství (B) jeho otočením do polohy 1 (nejmenší množství) až 4 nebo 6 (největší množství). B A 1. Stiskněte uvolňovací tlačítko (D) a otevřete víko (C). 2. Nalijte leštidlo (A), dokud kapalina nedosáhne hladiny „max“. 3. Rozlité leštidlo setřete savým hadříkem, aby se netvořilo přílišné množství pěny. 4. Zavřete víko.
www.aeg.com A 30 B Spuštění programu s odloženým startem D 20 C 1. Stiskněte uvolňovací tlačítko (B) a otevřete víko (C). 2. Mycí prostředek či tabletu vložte do komory (A). 3. Pokud program zahrnuje fázi předmytí, přidejte trochu mycího prostředku do komory (D). 4. Zavřete víko. Ujistěte se, že se uvolňovací tlačítko zaklapne zpět. 9.2 Nastavení a spuštění programu Funkce Auto Off Tato funkce snižuje spotřebu energie automatickým vypnutím nepracujícího spotřebiče.
ČESKY Žádná tlačítka kromě tlačítka Zap/Vyp nesvítí. 1. Stiskněte tlačítko Zap/Vyp nebo vyčkejte, až funkce Auto Off automaticky vypne spotřebič. 15 Pokud jste otevřeli dvířka před zapnutím Auto Off, spotřebič se automaticky vypne. 2. Zavřete vodovodní kohoutek. 10. TIPY A RADY 10.1 Obecné informace Následující rady zajistí optimální výsledky mytí a sušení při každodenním používání a také pomohou chránit životní prostředí. • • • • • • Z nádobí odstraňte větší zbytky jídla, které dejte do odpadu.
www.aeg.com • • • • • • Připálené zbytky jídel na nádobí nechte změknout. Duté nádobí (např. šálky, sklenice, hrnce) pokládejte dnem vzhůru. Přesvědčte se, že se sklenice vzájemně nedotýkají. Malé kusy nádobí a příbory vložte do košíčku na příbory. Lehké kusy vložte do horního koše. Dbejte na to, aby se jednotlivé kusy nádobí nehýbaly. Před spuštěním programu zkontrolujte, zda se ostřikovací ramena mohou volně otáčet. 10.5 Před spuštěním programu • • • • • Ostřikovací ramena nejsou zanesená.
ČESKY 17 8. Vložte zpět filtr (B) do plochého filtru (A). Otočte jím po směru hodinových ručiček, dokud se nezajistí. 2. Vyndejte filtr (C) ze sestavy filtru (B). 3. Vyjměte plochý filtr (A). POZOR! Nesprávné umístění filtrů může mít z následek špatné výsledky mytí a poškození spotřebiče. 4. Filtry omyjte. 11.2 Čištění ostřikovacích ramen Ostřikovací ramena nevyjímejte. Jestliže se otvory v ostřikovacích ramenech zanesou nečistotami, odstraňte je úzkým špičatým předmětem. 11.
www.aeg.com prostředek pro myčky nádobí. Řiďte se pečlivě pokyny na balení výrobku. 12. ODSTRAŇOVÁNÍ ZÁVAD Pokud spotřebič nezačne pracovat nebo se během provozu zastavuje. Než se obrátíte na autorizované servisní středisko, ověřte si, zda dokážete problém vyřešit sami pomocí informací uvedených v tabulce. U některých poruch se na displeji zobrazí výstražný kód. Většinu problémů, které se objeví, lze vyřešit bez nutnosti kontaktovat autorizované servisní středisko.
ČESKY 19 Problém a výstražný kód Možná příčina a řešení Spotřebič se během chodu vícekrát zastaví a spustí. • Nejde o závadu. Zajišťují se tím optimální výsledky mytí a úspora energie. Program probíhá příliš dlou‐ ho. • • Byla zvolena funkce úspory energie. Pokud je nastavena funkce odloženého startu, zrušte nastavenou prodlevu nebo vyčkejte do konce odpočítá‐ vání. Na displeji se zvýší zbývající • čas a přeskočí téměř na ko‐ nec programu. Nejde o závadu. Spotřebič pracuje správně.
www.aeg.com Problém Možná příčina a řešení Špatné výsledky sušení. • • • • Na nádobí a skle jsou bílé šmouhy nebo modravý potah. • • Na sklenicích a nádobí jsou skvrny a zaschlé vodní kapky. • Nádobí je mokré. • • • • • Nádobí bylo ponecháno příliš dlouho uvnitř zavřeného spotřebiče. Došlo leštidlo nebo je nedostatečné dávkování lešti‐ dla. Nastavte dávkování leštidla na vyšší stupeň. Plastové předměty mohou vyžadovat osušení utěrkou.
ČESKY Problém 21 Možná příčina a řešení Matné, zbarvené či naštípnuté • nádobí. • • Ujistěte se, že do spotřebiče vkládáte pouze nádobí, které lze bezpečně mýt v myčce nádobí. Koš plňte a vyprazdňujte opatrně. Viz leták o plnění košů. Křehké kusy nádobí vložte do horního koše. Ohledně dalších možných příčin viz části „Před prvním použitím“, „Denní používání“ nebo „Tipy a rady“. 13.
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.....................................................................................23 2. VEILIGHEIDSVOORSCHRIFTEN............................................................................ 24 3. BESCHRIJVING VAN HET PRODUCT................................................................... 26 4. BEDIENINGSPANEEL ............................................................................................ 27 5. PROGRAMMA’S..............................
NEDERLANDS 1. 23 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant. 25 • Speel niet met het water van het apparaat en drink het niet op.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 4 7 5 6 6 Start-toets 7 Indicatielampjes 8 Option-toets 4.1 Indicatielampjes Aanduiding Beschrijving Wasfase. Gaat aan wanneer de wasfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. Multitab-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje.
www.aeg.com 5.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Programmaduur (min.) 8-9 1.1 - 1.3 55 - 65 9 0.8 30 4 0.1 14 29 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.com Schrijf het productnummer (PNC) op dat u op het typeplaatje vindt. 6. INSTELLINGEN 6.
www.aeg.com Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
NEDERLANDS Het uitschakelen van het glansmiddeldoseerbakje Na het beëindigen van het programma klinkt er tevens een geluidssignaal. Dit geluidssignaal is standaard uitgeschakeld, maar kan worden geactiveerd. Het apparaat moet in de programmakeuzemodus staan. 1. Houd om de gebruikersmodus in te voeren tegelijkertijd Delay en Start ingedrukt tot de indicatielampjes , en gaan knipperen en het display blanco is. 2. Druk op Option.
www.aeg.com Deze optie schakelt de afgifte van zout uit. Het zoutindicatielampje gaat niet branden. Met deze optie wordt de programmaduur verlengd om de schoonmaak- en droogresultaten te verbeteren met het gebruik van multitabletten. Multitab is geen permanente optie en moet elke cyclus geselecteerd worden. Multitab activeren Druk op Option totdat het indicatielampje aan gaat. - De vaat kan nog nat zijn als het programma klaar is. De duur van het programma zal korter zijn.
NEDERLANDS 33 B A M AX 4 1 3 2 + - 5. Draai de dop van het zoutreservoir rechtsom om het zoutreservoir te sluiten. Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Gevaar voor roest. Start om dit te voorkomen een programma nadat u het zoutreservoir heeft bijgevuld. 8.2 Het vullen van het glansmiddeldoseerbakje A D B C C D LET OP! Gebruik alleen glansspoelmiddel voor afwasautomaten. 1. Druk op de ontgrendelknop (D) om de deksel te openen (C). 2.
www.aeg.com 9.1 Vaatwasmiddel gebruiken 1. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de keuzemodus Programma staat. 2. Sluit de deur van het apparaat. 3. Blijf op Program drukken tot de aanduiding van het programma dat u wilt instellen verschijnt. Het display geeft de programmaduur weer. 4. Stel de bruikbare opties in. 5. Druk op Start om het programma te starten. • Het wasfase-indicatielampje gaat branden. • De programmaduur neemt af in stappen van 1 minuut.
NEDERLANDS De uitgestelde start annuleren tijdens het aftellen Als u de uitgestelde start annuleert, moet u het programma en de opties opnieuw instellen. Houd tegelijkertijd Program en Option ingedrukt tot het apparaat in de programmakeuzemodus staat. Het programma annuleren Houd tegelijkertijd Program en Option ingedrukt tot het apparaat in de programmakeuzemodus staat. Controleer of er afwasmiddel in het afwasmiddeldoseerbakje aanwezig is voordat u een nieuw programma start.
www.aeg.com instructies van de vaatwasmiddelfabrikant. 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4.
NEDERLANDS 37 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter terug (A). Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
www.aeg.com LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen.
NEDERLANDS 39 Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat neemt geen water. Op het display verschijnt • Controleer of de waterkraan is geopend. • Zorg dat de waterdruk niet te laag is. Neem hiervoor zo nodig contact op met uw lokale waterleidingbedrijf. • Controleer of de waterkraan niet verstopt is. • Controleer of het filter in de toevoerslang niet verstopt is. • Controleer of er geen knikken of bochten in de watertoevoerslang aanwezig zijn. .
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat maakt kortsluiting. • De stroomsterkte is onvoldoende om alle tegelijk werkende apparaten van stroom te voorzien. Controleer de stroomsterkte van het stopcontact en het vermogen op de meter, of zet één van de in gebruik zijnde apparaten uit. • Interne elektrische storing van het apparaat. Neem contact op met een servicecentrum.
NEDERLANDS 41 Probleem Mogelijke oorzaak en oplossing Het serviesgoed is nat. • Het programma heeft geen droogfase of heeft een droogfase met lage temperatuur. • Het glansmiddeldoseerbakje is leeg. • De kwaliteit van het glansmiddel kan de oorzaak zijn. • De kwaliteit van de multitabletten kan de oorzaak zijn. Probeer een ander merk of activeer het glansmiddeldoseerbakje en gebruik het glansmiddel samen met de multitabletten. De binnenkant van het apparaat is nat. • Dit is geen fout van het apparaat.
www.aeg.com 13. TECHNISCHE INFORMATIE Afmetingen Breedte / hoogte / diepte (mm) 600 / 850 / 625 Elektrische aansluiting 1) Voltage (V) 220 - 240 Frequentie (Hz) 50 Watertoevoerdruk Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 13 Energieverbruik Modus aan laten (W) 0.99 Energieverbruik Uit-modus (W) 0.10 1) Zie het typeplaatje voor andere waarden.
FRANÇAIS 43 TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 44 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 45 3. DESCRIPTION DE L'APPAREIL.............................................................................. 47 4. BANDEAU DE COMMANDE................................................................................. 48 5. PROGRAMMES.............................
1. www.aeg.com CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • • • 45 Respectez le nombre maximum de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
www.aeg.com • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
FRANÇAIS 3.
www.aeg.com 4. BANDEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Touche Program Voyants de programme Affichage Touche Delay 3 4 7 5 6 6 Touche Start 7 Voyants 8 Touche Option 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant Multitab. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme.
FRANÇAIS 49 5.
www.aeg.com Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 7 - 12 0.6 - 1.4 40 - 150 13 - 15 1.5 - 1.6 150 - 170 8-9 1.1 - 1.3 55 - 65 9 0.8 30 4 0.1 14 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut 51 vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage.
www.aeg.com 6.3 Distributeur de liquide de rinçage Le liquide de rinçage permet de sécher la vaisselle sans laisser de traînées ni de taches. Le liquide de rinçage est automatiquement ajouté au cours de la phase de rinçage chaud. Utilisation du liquide de rinçage et des pastilles touten-un Lorsque vous activez l'option Multitab, le distributeur de liquide de rinçage continue à libérer le liquide de rinçage. Vous pouvez cependant désactiver le distributeur de liquide de rinçage.
FRANÇAIS 53 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver d'options pendant le déroulement d'un programme. Certaines options ne sont pas compatibles entre elles. Si vous avez choisi des options incompatibles, l'appareil en désactivera automatiquement une ou plusieurs. Seuls les voyants correspondant aux options encore actives resteront allumés. 7.
www.aeg.com 8.1 Réservoir de sel régénérant ATTENTION! Utilisez uniquement du sel régénérant conçu pour les lave-vaisselle. Le sel permet de recharger la résine dans l'adoucisseur d'eau et de garantir de bons résultats de lavage en utilisation quotidienne. Remplissage du réservoir de sel régénérant De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion. Afin d'éviter cela, après avoir rempli le réservoir de sel régénérant, démarrez un programme.
FRANÇAIS absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le bouton d'ouverture se verrouille correctement. 55 Vous pouvez tourner le sélecteur de quantité délivrée (B) entre la position 1 (quantité minimale) et la position 4 ou 6 (quantité maximale). 9. UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation.
www.aeg.com Départ d'un programme 1. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Sélection de programme. 2. Fermez la porte de l'appareil. 3. Appuyez sur la touche Program à plusieurs reprises jusqu'à ce que le voyant du programme que vous souhaitez sélectionner s'allume. L'affichage indique la durée du programme. 4. Sélectionnez les options compatibles. 5. Appuyez sur la touche Start pour lancer le programme.
FRANÇAIS 57 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable. En cas de besoin, utilisez le programme de prélavage (si disponible) ou sélectionnez un programme avec une phase de prélavage. • Utilisez toujours tout l'espace des paniers.
www.aeg.com en fonction de la dureté de l'eau dans votre région. 5. Ajustez la quantité de liquide de rinçage libérée. 10.4 Chargement des paniers • Utilisez uniquement cet appareil pour laver des articles qui peuvent passer au lave-vaisselle. • Ne mettez pas dans le lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre. • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage).
FRANÇAIS 59 C B A 1. Tournez le filtre (B) vers la gauche et sortez-le. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat (A) en place. Assurez-vous qu'il est correctement positionné sous les 2 guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
www.aeg.com ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres.
FRANÇAIS 61 Problème et code d'alarme Cause et solution possibles Le programme ne démarre pas. • Vérifiez que la porte de l'appareil est fermée. • Appuyez sur Start. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte. • L'appareil a lancé la procédure de rechargement de la résine dans l'adoucisseur d'eau. La durée de cette procédure est d'environ 5 minutes. L'appareil ne se remplit pas d'eau. • Assurez-vous que le robinet d'eau est ouvert.
www.aeg.com Problème et code d'alarme Cause et solution possibles Bruit de cliquetis ou de battement à l'intérieur de l'appareil. • La vaisselle n'est pas correctement rangée dans les paniers. Reportez-vous au manuel de chargement du panier. • Assurez-vous que les bras d'aspersion peuvent tourner librement. L'appareil déclenche le disjoncteur. • L'ampérage n'est pas suffisant pour alimenter tous les appareils en cours de fonctionnement simultanément.
FRANÇAIS 63 Problème Cause et solution possibles Il y a des taches et traces de gouttes d'eau séchées sur les verres et la vaisselle. • La quantité de liquide de rinçage libérée n'est pas suffisante. Placez le sélecteur de dosage du liquide de rinçage sur un niveau plus élevé. • Il se peut que la qualité du liquide de rinçage soit en cause. La vaisselle est mouillée. • Le programme ne contient pas de phase de séchage ou une phase de séchage à basse température.
www.aeg.com Problème Cause et solution possibles Vaisselle ternie, décolorée ou ébréchée. • Assurez-vous de ne placer dans l'appareil que des articles adaptés au lave-vaisselle. • Chargez et déchargez le panier avec précautions. Reportez-vous au manuel de chargement du panier. • Placez les objets délicats dans le panier supérieur. Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 13.
FRANÇAIS 65
www.aeg.
FRANÇAIS 67
100001371-A-152015 www.aeg.