NL FR DE Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle Benutzerinformation Geschirrspüler 2 22 43 FAVORIT56322IM0
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Aan/uit-toets Programma-indicatielampjes Indicatielampjes Weergave Delay-toets TimeSaver-toets 7 8 9 10 Multitab-toets Programmakeuzetoets (omhoog) Programmakeuzetoets (omlaag) Reset-toets 4.1 Indicatielampjes Aanduiding Omschrijving Multitab-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje.
www.aeg.com 5.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) 13 - 15 1.3 - 1.5 140 - 160 13 - 14 0.7 - 0.9 70 - 80 9 0.9 30 4 0.1 14 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten info.test@dishwasher-production.com Schrijf het productnummer (PNC) op dat u op het typeplaatje vindt.
www.aeg.com Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Fabrieksinstelling. 2) Gebruik geen zout op dit niveau.
NEDERLANDS Glansmiddeldosering geactiveerd. 3. Druk op om de instelling te 11 Het lampje glansmiddel gaat uit. 4. Druk op de knop aan/uit om de instelling te bevestigen. wijzigen. = Glansmiddeldosering gedeactiveerd. 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd. De opties kunnen niet worden in- of uitgeschakeld als een programma in werking is. 7.1 Multitab Activeer deze optie als u multitabletten gebruikt met zout, glansmiddel en wasmiddel in één tablet.
www.aeg.com 8.1 Het zoutreservoir LET OP! Gebruik uitsluitend zout dat specifiek is bedoeld voor gebruik in vaatwassers. 8.2 Het vullen van het glansmiddeldoseerbakje A D B Het zout wordt gebruikt om de hars in de waterontharder te herladen en voor goede wasresultaten voor dagelijks gebruik. Het zoutreservoir vullen: 1. Draai de dop linksom om het zoutreservoir te openen. 2. Doe 1 liter water in het zoutreservoir (alleen de eerste keer). 3. Vul het zoutreservoir met regenereerzout.
NEDERLANDS 13 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de keuzemodus Programma staat. • Vul het zoutreservoir als het zoutindicatielampje brandt. • Vul het glansmiddeldoseerbakje als het indicatielampje van het glansmiddel brandt. 3. Ruim de korven in. 4. Voeg vaatwasmiddel toe. Activeer de optie Multitab als u multitabletten gebruikt. 5.
www.aeg.com Een programma starten met een uitgestelde start De uitgestelde start annuleren tijdens het aftellen 1. Stel een programma in. 2. Blijf op Delay drukken tot het display de uitgestelde tijd toont die u wilt instellen (van 1 tot 24 uur). Het indicatielampje van het geselecteerde programma blijft knipperen. 3. Sluit de deur van het apparaat om het aftellen te starten. Het programma-indicatielampje stopt met knipperen en gaat branden.
NEDERLANDS 10.2 Gebruik van zout, glansmiddel en vaatwasmiddel • Gebruik enkel zout, glansmiddel en vaatwasmiddel voor afwasautomaten. Overige producten kunnen het apparaat beschadigen. • Multitabletten zijn doorgaans geschikt voor een waterhardheid tot 21 °dH. Bij een hogere waterhardheid moet zout, glansmiddel en vaatwasmiddel worden gebruikt naast het gebruik van multitabletten.
www.aeg.com 10.6 De rekken uitruimen Aan het einde van het programma kan er water aan de zijkanten en de deur van het apparaat achterblijven. 1. Laat de borden afkoelen voordat u deze uit het apparaat neemt Hete borden zijn gevoelig voor beschadigingen. 2. Ruim eerst het onderrek en dan het bovenrek uit 11. ONDERHOUD EN REINIGING WAARSCHUWING! Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht.
NEDERLANDS 17 openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit.
www.aeg.com Het merendeel van de voorkomende problemen kan worden opgelost zonder contact op te hoeven nemen met een erkend servicecentrum. Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren. • Zorg dat de stekker in het stopcontact zit. • Zorg dat er geen zekering in de zekeringenkast is doorgebrand. Het programma start niet. • Zorg dat de deur van het apparaat is gesloten.
NEDERLANDS 19 Probleem en alarmcode Mogelijke oorzaak en oplossing Weinig lekkage uit de deur van het apparaat. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • De deur van het apparaat is niet gecentreerd op de kuip. Verstel de achterpoot (indien van toepassing). De deur van het apparaat sluit moeilijk. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • Delen van het serviesgoed steken uit de korven.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Witte strepen of een blauwe waas op glazen en serviesgoed. • De vrijgegeven hoeveelheid glansmiddel is te hoog. Zet de dosering van het glansmiddel op een lagere stand. • Er is te veel vaatwasmiddel gebruikt. Vlekken en opgedroogde watervlekken op glazen en servies. • De vrijgegeven hoeveelheid glansmiddel is te laag. Zet de dosering van het glansmiddel op een hogere stand. • De kwaliteit van het glansmiddel kan de oorzaak zijn.
NEDERLANDS 21 Probleem Mogelijke oorzaak en oplossing Dof, ontkleurd of afgeschilverd serviesgoed. • Zorg dat alleen vaatwasmachinebestendige voorwerpen in het apparaat worden gewassen. • Laad de korf voorzichtig in en uit. Raadpleeg de folder laden van de korf. • Leg tere voorwerpen in het bovenrek. Raadpleeg "Voor het eerste gebruik", "Dagelijks gebruik" of "Aanwijzingen en tips" voor mogelijke andere oorzaken. 13.
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 23 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 24 3. DESCRIPTION DE L'APPAREIL.............................................................................. 26 4. BANDEAU DE COMMANDE................................................................................. 27 5. PROGRAMMES..........................
FRANÇAIS 1. 23 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3.
FRANÇAIS 27 4. BANDEAU DE COMMANDE 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Touche Marche/Arrêt Voyants de programme Voyants Affichage Touche Delay Touche TimeSaver 7 8 9 10 Touche Multitab Touche Programme (haut) Touche Programme (bas) Touche Reset 4.1 Voyants Voyant Description Voyant Multitab. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage.
www.aeg.com 5.
FRANÇAIS Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 7 - 12 0.6 - 1.4 40 - 150 13 - 15 1.3 - 1.5 140 - 160 13 - 14 0.7 - 0.9 70 - 80 9 0.9 30 4 0.1 14 29 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com Dureté de l'eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.
FRANÇAIS Comment désactiver le distributeur de liquide de rinçage L'appareil doit être en mode Programmation. 1. Pour entrer en mode utilisateur, maintenez les touches et enfoncées jusqu'à ce que les voyants , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur la touche • Les voyants s'éteignent. 31 • Le voyant continue à clignoter. • L'affichage indique le réglage actuel : = distributeur de liquide de rinçage activé 3. Appuyez sur pour modifier le réglage.
www.aeg.com 2. Remplissez le réservoir de sel régénérant. 3. Remplissez le distributeur de liquide de rinçage. 4. Ouvrez le robinet d'eau. 5. Lancez un programme pour éliminer tous les résidus qui peuvent toujours se trouver à l'intérieur de l'appareil. N'utilisez pas de produit de lavage et ne chargez pas les paniers. Lorsque vous démarrez un programme, l'appareil peut prendre 5 minutes pour recharger la résine dans l'adoucisseur d'eau. Pendant ce temps, l'appareil semble ne pas fonctionner.
FRANÇAIS ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. 33 absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le bouton d'ouverture se verrouille correctement. Vous pouvez tourner le sélecteur de quantité délivrée (B) entre la position 1 (quantité minimale) et la position 4 ou 6 (quantité maximale). 1. Appuyez sur le bouton d'ouverture (D) pour ouvrir le couvercle (C). 2.
www.aeg.com • 5 minutes après la fin du programme de lavage. • Au bout de 5 minutes si le programme n'a pas démarré. Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3. Appuyez sur ou pour sélectionner un programme. • Le voyant du programme sélectionné clignote. • L'affichage indique la durée du programme. 4. Sélectionnez les options compatibles. 5.
FRANÇAIS 35 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable. En cas de besoin, utilisez le programme de prélavage (si disponible) ou sélectionnez un programme avec une phase de prélavage. • Utilisez toujours tout l'espace des paniers.
www.aeg.com en fonction de la dureté de l'eau dans votre région. 5. Ajustez la quantité de liquide de rinçage libérée. 10.5 Avant le démarrage d'un programme 10.4 Chargement des paniers • Les filtres sont propres et correctement installés. • Le bouchon du réservoir de sel régénérant est vissé. • Les bras d'aspersion ne sont pas obstrués. • Vous avez utilisé du sel régénérant et du liquide de rinçage (sauf si vous utilisez des pastilles tout en 1).
FRANÇAIS 37 C B A 1. Tournez le filtre (B) vers la gauche et sortez-le. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat (A) en place. Assurez-vous qu'il est correctement positionné sous les 2 guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
www.aeg.com ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d’aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres.
FRANÇAIS 39 Problème et code d'alarme Cause et solution possibles Le programme ne démarre pas. • Vérifiez que la porte de l'appareil est fermée. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte. • L'appareil a lancé la procédure de rechargement de la résine dans l'adoucisseur d'eau. La durée de cette procédure est d'environ 5 minutes. L'appareil ne se remplit pas d'eau. • Assurez-vous que le robinet d'eau est ouvert.
www.aeg.com Problème et code d'alarme Cause et solution possibles Bruit de cliquetis ou de battement à l'intérieur de l'appareil. • La vaisselle n'est pas correctement rangée dans les paniers. Reportez-vous au manuel de chargement du panier. • Assurez-vous que les bras d'aspersion peuvent tourner librement. L'appareil déclenche le disjoncteur. • L'ampérage n'est pas suffisant pour alimenter tous les appareils en cours de fonctionnement simultanément.
FRANÇAIS 41 Problème Cause et solution possibles Il y a des taches et traces de gouttes d'eau séchées sur les verres et la vaisselle. • La quantité de liquide de rinçage libérée n'est pas suffisante. Placez le sélecteur de dosage du liquide de rinçage sur un niveau plus élevé. • Il se peut que la qualité du liquide de rinçage soit en cause. La vaisselle est mouillée. • Le programme ne contient pas de phase de séchage ou une phase de séchage à basse température.
www.aeg.com Problème Cause et solution possibles Vaisselle ternie, décolorée ou ébréchée. • Assurez-vous de ne placer dans l'appareil que des articles adaptés au lave-vaisselle. • Chargez et déchargez le panier avec précautions. Reportez-vous au manuel de chargement du panier. • Placez les objets délicats dans le panier supérieur. Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 13.
DEUTSCH 43 INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.......................................................................... 44 2. SICHERHEITSANWEISUNGEN.............................................................................. 45 3. GERÄTEBESCHREIBUNG.......................................................................................47 4. BEDIENFELD........................................................................................................... 48 5. PROGRAMME.....................
1. www.aeg.com SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
DEUTSCH • • • • • • • • 45 Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. Stellen Sie Messer und Besteck mit scharfen Spitzen mit der Spitze nach unten in den Besteckkorb oder legen Sie sie waagerecht in das Gerät.
www.aeg.com • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist.
DEUTSCH • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in dem Gerät einschließen. 3.
www.aeg.com 4. BEDIENFELD 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Taste „Ein/Aus“ Programmkontrolllampen Kontrolllampen Display Taste Delay Taste TimeSaver 7 8 9 10 Taste Multitab Programmtaste (nach oben) Programmtaste (nach unten) Taste Reset 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Multitab Kontrolllampe Salz Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel Sie erlischt während des Programmbetriebs.
DEUTSCH 49 5.
www.aeg.com 5.1 Verbrauchswerte Programm 1) Wasser (l) Energieverbrauch (kWh) Dauer (Min.) 9.9 0.932 195 7 - 12 0.6 - 1.4 40 - 150 13 - 15 1.3 - 1.5 140 - 160 13 - 14 0.7 - 0.9 70 - 80 9 0.9 30 4 0.1 14 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Möchten Sie Informationen zum Leistungstest erhalten, schicken Sie eine E-Mail an: info.
DEUTSCH 51 Wasserhärte Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH). mmol/l Clarke Was- Einstellung für den serhärteWasserenthärter grade 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.
www.aeg.com Ausschalten des KlarspülmittelDosierers Das Gerät muss sich im Programmwahlmodus befinden. Einstellung angezeigt: Klarspülmittel-Dosierer eingeschaltet. 1. Halten Sie zum Aufrufen des Benutzermodus gleichzeitig und gedrückt, bis die Kontrolllampen , und blinken und das Display nichts anzeigt. 2. Drücken Sie . • Die Kontrolllampen erlöschen. • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle und 3. Drücken Sie = zum Ändern der Einstellung.
DEUTSCH in Ihrem Gebiet entspricht. Wenn nicht, stellen Sie die Wasserenthärterstufe ein. 2. Füllen Sie den Salzbehälter. 3. Füllen Sie den KlarspülmittelDosierer. 4. Öffnen Sie den Wasserhahn. 5. Starten Sie ein Programm, um Fertigungsrückstände, die sich möglicherweise noch im Gerät befinden können, zu beseitigen. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. Wenn Sie ein Programm starten, kann es bis zu 5 Minuten dauern das Filterharz des Wasserenthärters zu regenerieren.
www.aeg.com ACHTUNG! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. Tuch auf, um zu große Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet. 1. Drücken Sie die Entriegelungstaste (D), um den Deckel (C) zu öffnen. 2. Füllen Sie den KlarspülmittelDosierer (A) bis zur Markierung „max“. 3.
DEUTSCH 55 • Nach 5 Minuten, wenn das Programm nicht gestartet wurde. Öffnen der Tür während eines laufenden Programms Starten eines Programms Wenn Sie die Tür während eines laufenden Programms öffnen, stoppt das Gerät. Wenn Sie die Tür wieder schließen, läuft das Programm ab dem Zeitpunkt der Unterbrechung weiter. 1. Lassen Sie die Gerätetür einen Spaltbreit offen. 2. Drücken Sie die Taste „Ein/Aus“, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. 3.
www.aeg.com 10. TIPPS UND HINWEISE 10.1 Allgemeines Die folgenden Hinweise stellen optimale Reinigungs- und Trocknungsergebnisse im täglichen Gebrauch sicher, und tragen auch zum Umweltschutz bei. • Schütten Sie größere Lebensmittelreste auf dem Geschirr in den Abfallbehälter. • Spülen Sie das Geschirr nicht von Hand vor. Verwenden Sie bei Bedarf das Vorspülprogramm (wenn verfügbar) oder wählen Sie ein Programm mit Vorspülgang. • Nutzen Sie die Körbe immer ganz aus.
DEUTSCH • Spülen Sie im Gerät keine Geschirrteile aus Holz, Horn, Aluminium, Zinn oder Kupfer. • Spülen Sie in diesem Gerät keine Gegenstände, die Wasser aufnehmen können (Schwämme, Geschirrtücher usw.). • Entfernen Sie Speisereste vom Geschirr. • Weichen Sie eingebrannte Essensreste ein. • Ordnen Sie hohle Gefäße (z. B. Tassen, Gläser, Pfannen) mit der Öffnung nach unten ein. • Stellen Sie sicher, dass Geschirr und Besteck nicht aneinander haften. Mischen Sie Löffel mit anderem Besteck.
www.aeg.com C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein. Stellen Sie sicher, dass er korrekt unter den beiden Führungen eingesetzt wurde. 7.
DEUTSCH ACHTUNG! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger.
www.aeg.com Problem und Alarmcode Mögliche Ursachen und Abhilfe Das Programm startet nicht. • Vergewissern Sie sich, dass die Tür geschlossen ist. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab, oder warten Sie, bis sie abgelaufen ist. • Das Gerät regeneriert das Filterharz des Wasserenthärters. Dieser Vorgang dauert ca. 5 Minuten. Es läuft kein Wasser in das Gerät. • Vergewissern Sie sich, dass der Wasserzulauf geöffnet ist.
DEUTSCH 61 Problem und Alarmcode Mögliche Ursachen und Abhilfe Die Gerätetür ist schwer zu schließen. • Das Gerät steht nicht waagrecht. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden). • Teile des Geschirrs ragen aus den Körben heraus. Klappernde/schlagende Geräusche aus dem Geräteinneren. • Das Geschirr ist nicht richtig in den Körben eingeordnet. Siehe Broschüre zum Beladen der Körbe. • Achten Sie darauf, dass sich die Sprüharme frei drehen können.
www.aeg.com Problem Mögliche Ursachen und Abhilfe Wasserflecken und andere Flecken auf Gläsern und Geschirr. • Die zugegebene Klarspülmittelmenge ist zu niedrig. Stellen Sie den Dosierwähler für Klarspülmittel höher ein. • Die Ursache kann in der Qualität des Klarspülmittels liegen. Das Geschirr ist nass. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur. • Der Klarspülmittel-Dosierer ist leer.
DEUTSCH 63 Siehe „Vor der ersten Inbetriebnahme“, „Täglicher Gebrauch“ oder „Tipps und Hinweise“ bezüglich anderer möglicher Ursachen. 13. TECHNISCHE DATEN Abmessungen Breite/Höhe/Tiefe (mm) 596 / 818 - 898 / 575 Elektrischer Anschluss 1) Spannung (V) 200 - 240 Frequenz (Hz) 50 / 60 Wasserdruck Min./max. bar (MPa) 0.5 (0.05) / 8 (0.8) Wasserversorgung Kalt- oder Warmwasser 2) max. 60 °C Fassungsvermögen Maßgedecke 13 Leistungsaufnahme Ein-Zustand (W) 0.
100003391-B-112015 www.aeg.