NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 24 45 F56352M0 F56352W0
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 2 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL ................................................................................................ 7 5. PROGRAMMA’S..................
NEDERLANDS 3 niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • • • Houd rekening met het maximale aantal 13 plaatsen. Als de voedingskabel beschadigd is, moet de fabrikant, een erkende serviceverlener of een gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Leg het bestek in de besteklade met de scherpe randen naar beneden of leg ze horizontaal in de besteklade met de scherpe randen naar beneden. Laat om ongelukken te voorkomen het apparaat niet onbeheerd achter met open deur.
NEDERLANDS • • • • vervangen, dan moet dit gebeuren door onze Klantenservice. Steek de stekker pas in het stopcontact als de installatie is voltooid. Zorg ervoor dat het netsnoer na installatie bereikbaar is. Trek niet aan het netsnoer om het apparaat los te koppelen. Trek altijd aan de stekker. Dit apparaat voldoet aan de EUrichtlijnen. Alleen het Verenigd Koninkrijk en Ierland. Het apparaat is voorzien van een 13 ampère stekker.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 4 7 5 6 6 Start-toets 7 Indicatielampjes 8 Option-toets 4.1 Indicatielampjes Aanduiding Beschrijving Wasfase. Gaat aan wanneer de wasfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. TimeSaver-indicatielampje. XtraDry-indicatielampje. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Zoutindicatielampje.
www.aeg.com 5.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Programmaduur (min.) 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 4 0.1 14 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Om de nodige informatie te ontvangen over het uitvoeren van prestatietesten (bijv. volgens EN60436) stuurt u een email naar: info.test@dishwasher-production.
www.aeg.com Hoe hoger het gehalte van deze mineralen, des te harder is het water. De waterhardheid wordt gemeten in de volgende gelijkwaardige schalen. De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten.
NEDERLANDS droogprestaties dient u echter altijd glansmiddel te gebruiken. Schakel de aanduiding in om de glansmiddelindicator actief te houden als u standaard wasmiddel of multitabletten zonder glansmiddel gebruikt. Het uitschakelen van de melding van een leeg glansmiddeldoseerbakje (indien van toepassing). 1. Druk op Option. en • Het indicatielampje blijft knipperen. • Het display toont de huidige instelling.
www.aeg.com 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd. De opties kunnen niet worden in- of uitgeschakeld als een programma in werking is. De knop Option schakelt tussen de beschikbare opties en hun mogelijke combinaties. Niet alle opties kunnen met elkaar worden gecombineerd. Als u opties hebt geselecteerd die niet met elkaar te combineren zijn, dan schakelt het apparaat automatisch één of meerdere opties uit.
NEDERLANDS de waterhardheid in uw omgeving. Indien niet, stel dan de stand van de waterontharder juist in. 2. Vul het zoutreservoir. 3. Vul het glansmiddeldoseerbakje. 4. Draai de waterkraan open. 5. Start een programma om resten te verwijderen die misschien nog in het apparaat zijn achtergebleven. Gebruik geen afwasmiddel en belaadt de manden niet. Na het starten van een programma, doet het apparaat er ongeveer 5 minuten over om de hars in de waterontharder te herladen.
www.aeg.com LET OP! Gebruik alleen glansspoelmiddel voor afwasautomaten. voorkomen dat er te veel schuim ontstaat. 4. Sluit het deksel. Zorg ervoor dat het ontgrendelknopje op zijn plaats dichtklikt. 1. Druk op de ontgrendelknop (D) om de deksel te openen (C). 2. Giet het glansmiddel in het doseervakje (A) tot de vloeistof het niveau 'max' heeft bereikt. 3.
NEDERLANDS Een programma starten 15 Probeer de deur van het apparaat niet binnen 2 minuten nadat AirDry hem automatisch opent te openen, want dit kan schade aan het apparaat veroorzaken. Als hierna de deur gedurende nog 3 minuten wordt gesloten, beëindigt het draaiende programma. 1. Druk op de aan/uit-knop om het apparaat te activeren. Zorg dat het apparaat in de keuzemodus Programma staat. 2. Sluit de deur van het apparaat. 3.
www.aeg.com 10. AANWIJZINGEN EN TIPS 10.1 Algemeen De volgende tips zorgen voor optimale schoonmaak- en droogresultaten en helpen ook het milieu te beschermen. • Verwijder grotere etensresten van de borden en gooi ze in de vuilnisbak. • Spoel de vaat niet eerst af. Gebruik indien nodig een voorwasprogramma (indien beschikbaar) of selecteer een programma met een voorwasfase. • Gebruik altijd de hele ruimte van de mandjes.
NEDERLANDS • Leg lichte voorwerpen in het bovenrek. Zorg ervoor dat de voorwerpen niet kunnen verschuiven. • Doe bestek en kleine items in het bestekmand. • Zorg er voor dat de sproeiarmen vrij kunnen ronddraaien voordat u een programma start. 10.5 Voor het starten van een programma Controleer of: • De filters schoon zijn en correct zijn geplaatst. • De dop van het zoutreservoir goed dicht zit. • De sproeiarmen niet zijn verstopt.
www.aeg.com 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3. Verwijder de platte filter (A). 4. Was de filters. LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp.
NEDERLANDS schoonmaakproduct voor vaatwasmachines te gebruiken. Volg 19 de instructies op de verpakking van de producten zorgvuldig op. 12. PROBLEEMOPLOSSING Als het apparaat niet start of stopt tijdens de bediening, kijk dan of u het probleem zelf kunt oplossen met behulp van de informatie in de tabel of door contact op te nemen met een erkend servicecentrum. WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing De anti-overstromingsbevei- • Draai de waterkraan dicht en neem contact op met de liging is ingeschakeld. service-afdeling. Op het display verschijnt . Het apparaat stopt en start meerdere keren tijdens de werking. • Dat is normaal. Het voorziet in optimale reinigingsresultaten en energiebesparing. Het programma duurt te lang. • Kies de optie TimeSaver om de programmaduur te verkorten.
NEDERLANDS 21 12.1 De was- en droogresultaten zijn niet naar tevredenheid Probleem Mogelijke oorzaak en oplossing Slechte wasresultaten. • Raadpleeg "Dagelijks gebruik", "Aanwijzingen en tips" en de folder voor het laden van de korf. • Gebruik intensievere wasprogramma´s. • Maak de inspuiters van de sproeiarm en het filter schoon. Zie "Onderhoud en reiniging". Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Roestresten op bestek. • Er wordt voor het wassen teveel zout in het water gebruikt. Zie 'De waterontharder instellen'. • Zilver en roestvrijstalen bestek zijn samen geplaatst. Zet zilveren en roestvrijstalen voorwerpen niet dicht bij elkaar. Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water.
NEDERLANDS Watertoevoerdruk Min. / max. bar (MPa) Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 13 Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.10 23 0.5 (0.05) / 8 (0.8) 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door alternatieve, milieuvriendelijkere energiebronnen geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14.
www.aeg.com CONTENTS 1. SAFETY INFORMATION........................................................................................... 24 2. SAFETY INSTRUCTIONS...........................................................................................26 3. PRODUCT DESCRIPTION.........................................................................................28 4. CONTROL PANEL .................................................................................................... 29 5. PROGRAMMES......
ENGLISH 25 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses. • Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear. • Ensure that there are no visible water leaks during and after the first use of the appliance. • The water inlet hose has a safety valve and a sheath with an inner mains cable. 27 2.
www.aeg.com 3.
ENGLISH 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Start button 7 Indicators 8 Option button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Drying phase. It comes on when the drying phase operates. TimeSaver indicator. XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates.
www.aeg.com 5.
ENGLISH Programme 1) Water (l) Energy (kWh) Duration (min) 13 - 14 0.9 - 1.1 70 - 85 4 0.1 14 31 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes To receive the necessary information for conducting performance tests (e.g. according to EN60436), send an email to: info.test@dishwasher-production.
www.aeg.com Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
ENGLISH – = rinse aid empty notification deactivated. 2. Press Option to change the setting. 3. Press on/off to confirm the setting. 6.4 AirDry AirDry improves the drying results with less energy consumption. 33 AirDry is automatically activated with all programmes excluding applicable). (if To improve the drying performance refer to the XtraDry option or activate AirDry. CAUTION! If children have access to the appliance, it is advised to deactivate AirDry as opening the door may pose a danger.
www.aeg.com Activating options can affect the water and energy consumption as well as the programme duration. 7.1 XtraDry Activate this option to boost the drying performance. With XtraDry on, the duration of some programmes, water consumption and the last rinse temperature can be affected. XtraDry is a permanent option for all and need programmes other than not to be selected at every cycle. In the other programmes the setting of XtraDry is permanent and it is automatically used in next cycles.
ENGLISH 35 B A M AX 4 4. Carefully shake the funnel by its handle to get the last granules inside. 5. Remove the salt around the opening of the salt container. 6. Turn the cap of the salt container clockwise to close the salt container. CAUTION! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion. 8.2 How to fill the rinse aid dispenser A D B C 9. DAILY USE 1. Open the water tap.
www.aeg.com 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent 20 C 30 The function comes into operation: • 5 minutes after the completion of the programme.
ENGLISH Opening the door while the appliance operates Opening the door while a programme is running stops the appliance. It may affect the energy consumption and the programme duration. After closing the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function.
www.aeg.com 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose.
ENGLISH 39 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A).
www.aeg.com 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object.
ENGLISH 41 Problem and alarm code Possible cause and solution The program does not start. • Make sure that the appliance door is closed. • Press Start. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. The appliance does not fill with water. • Make sure that the water tap is open.
www.aeg.com Problem and alarm code Possible cause and solution The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. • Internal electrical fault of the appliance. Contact an Authorised Service Centre. Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes.
ENGLISH 43 Problem Possible cause and solution The dishes are wet. • For the best drying performance activate the option XtraDry and set AirDry . • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
www.aeg.com Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 600 / 850 / 625 Electrical connection 1) Voltage (V) 200 - 240 Frequency (Hz) 50 / 60 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.
FRANÇAIS 45 TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................45 2. CONSIGNES DE SÉCURITÉ......................................................................................47 3. DESCRIPTION DE L'APPAREIL.................................................................................49 4. BANDEAU DE COMMANDE ...................................................................................50 5. PROGRAMMES.......................
www.aeg.com pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables.
FRANÇAIS • • • • • • • • • 47 La pression de l'eau en fonctionnement (minimale et maximale) doit se situer entre 0.5 (0.05) / 8 (0.8) bar (MPa) Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger.
www.aeg.com • Vérifiez que les paramètres figurant sur la plaque signalétique correspondent aux données électriques de votre réseau. • Utilisez toujours une prise de courant de sécurité correctement installée. • N'utilisez pas d'adaptateurs multiprises ni de rallonges. • Veillez à ne pas endommager la fiche secteur ni le câble d'alimentation. Le remplacement du câble d'alimentation de l'appareil doit être effectué par notre service après-vente agréé.
FRANÇAIS 2.6 Mise au rebut • Coupez le câble d'alimentation et mettez-le au rebut. • Retirez le dispositif de verrouillage de la porte pour empêcher les enfants et les animaux de s'enfermer dans l'appareil. AVERTISSEMENT! Risque de blessure ou d'asphyxie. • Débranchez l'appareil de l'alimentation électrique. 3.
www.aeg.com 4. BANDEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Touche Program Voyants de programme Affichage Touche Delay 3 4 7 5 6 6 Touche Start 7 Voyants 8 Touche Option 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant TimeSaver. Voyant XtraDry. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme.
FRANÇAIS 51 5.
www.aeg.com Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 7 - 12 0.7 - 1.5 45 - 160 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 4 0.1 14 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS 53 Pour entrer en mode utilisateur, maintenez les touches Delay et Start enfoncées jusqu'à ce que les voyants Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. , et se mettent à clignoter et que plus rien ne s'affiche. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région.
www.aeg.com 2. Appuyez sur la touche Program plusieurs fois pour modifier le réglage. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.3 Notification de liquide de rinçage vide 2. Appuyez sur Option pour modifier le réglage. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.4 AirDry AirDry améliore les résultats de séchage en utilisant moins d'énergie. Le liquide de rinçage permet à la vaisselle de sécher sans traces ni taches.
FRANÇAIS Comment désactiver l'option AirDry Assurez-vous que l'appareil est en mode Utilisateur. 1. Appuyez sur Delay. • Les voyants éteints. et sont 55 • Le voyant clignote toujours. • L'affichage indique le réglage actuel : = AirDry activé. 2. Appuyez sur la touche Delay pour modifier le réglage : = AirDry désactivé. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 7. OPTIONS Les options souhaitées doivent être activées à chaque fois, avant de lancer un programme.
www.aeg.com La durée totale du programme diminue d'environ 50 %. Les résultats de lavage seront les mêmes qu'avec la durée normale du programme. Les résultats de séchage peuvent être moins satisfaisants. Comment activer l'option TimeSaver Appuyez sur la touche Option jusqu'à ce que le voyant s'allume. L'affichage indique la durée du programme réactualisée. 8. AVANT LA PREMIÈRE UTILISATION 1. Assurez-vous que le réglage actuel de l'adoucisseur d'eau est compatible avec la dureté de l'arrivée d'eau.
FRANÇAIS ATTENTION! De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Afin d'éviter la corrosion, lancez immédiatement un programme après avoir rempli le réservoir de sel régénérant. ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. 1. Appuyez sur le bouton d'ouverture (D) pour ouvrir le couvercle (C). 2. Versez le liquide de rinçage dans le distributeur (A) jusqu'à ce qu'il atteigne le niveau « max ». 3.
www.aeg.com 9.1 Utilisation du produit de lavage Départ d'un programme D A B 1. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 2. Fermez la porte de l'appareil. 3. Appuyez sur Program à plusieurs reprises jusqu'à ce que le voyant du programme que vous souhaitez sélectionner s'allume. L'affichage indique la durée du programme. 4. Sélectionnez les options compatibles. 5. Appuyez sur la touche Start pour lancer le programme.
FRANÇAIS Durant la phase de séchage, si la porte est ouverte pendant plus de 30 secondes, le programme en cours s'arrête. Ceci ne se produit pas si la porte est ouverte par la fonction AirDry. Ne tentez pas de refermer la porte dans les 2 minutes suivant son ouverture automatique par la fonction AirDry car vous pourriez endommager l'appareil. Si par la suite vous refermez la porte pendant 3 minutes, le programme en cours se termine.
www.aeg.com 10.2 Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil.
FRANÇAIS 10.6 Déchargement des paniers 61 2. Commencez par décharger le panier inférieur, puis le panier supérieur. À la fin du programme, il peut rester de l'eau sur les parois et la porte de l'appareil. 1. Attendez que la vaisselle refroidisse avant de la retirer de l'appareil. La vaisselle encore chaude est sensible aux chocs. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
www.aeg.com bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le vers la droite jusqu'à la butée.
FRANÇAIS 63 La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé. Problème et code d'alarme Cause et solution possibles L'appareil ne s'allume pas. • Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. • Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles. Le programme ne démarre pas. • Vérifiez que le hublot de l'appareil est fermé. • Appuyez sur Start.
www.aeg.com Problème et code d'alarme Cause et solution possibles Le temps restant sur l'affi• Ceci est normal. L'appareil fonctionne correctement. chage augmente et passe presque instantanément à la fin du programme. Petite fuite au niveau de la porte de l'appareil. • L'appareil n'est pas de niveau. Desserrez ou serrez les pieds réglables (si disponibles). • La porte de l'appareil n'est pas centrée avec la cuve. Réglez le pied arrière (si disponible). La porte de l'appareil est difficile à fermer.
FRANÇAIS 65 Problème Cause et solution possibles Résultats de séchage insatisfaisants. • La vaisselle est restée trop longtemps à l'intérieur de l'appareil, porte fermée. • Il n'y a pas de liquide de rinçage ou le dosage du liquide de rinçage n'est pas suffisant. Augmentez le niveau de distributeur de liquide de rinçage. • Les articles en plastiques peuvent avoir besoin d'être essuyés. • Pour de meilleures performances de séchage, activez l'option XtraDry et sélectionnez AirDry.
www.aeg.com Problème Cause et solution possibles Il y a des résidus de détergent • La pastille de détergent est restée coincée dans le disdans le distributeur de produit tributeur de produit de lavage, qui n'a donc pas été de lavage à la fin du programentièrement éliminée par l'eau. me • L'eau ne peut pas éliminer le détergent du distributeur de produit de lavage. Assurez-vous que le bras d'aspersion n'est pas bloqué ou obstrué.
FRANÇAIS Pression de l'arrivée d'eau Min. / max. bar (MPa) Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.10 67 0.5 (0.05) / 8 (0.8) 1) Reportez-vous à la plaque signalétique pour d'autres valeurs.
156904711-A-092018 www.aeg.