EN FR DE User Manual Dishwasher Notice d'utilisation Lave-vaisselle Benutzerinformation Geschirrspüler 2 23 46 F56369M0
www.aeg.com CONTENTS 1. SAFETY INFORMATION...........................................................................................3 2. SAFETY INSTRUCTIONS.......................................................................................... 4 3. PRODUCT DESCRIPTION........................................................................................ 5 4. CONTROL PANEL ....................................................................................................6 5. PROGRAMMES.............
ENGLISH 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH • The water inlet hose has a safety valve and a sheath with an inner mains cable. • • • • WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging.
www.aeg.com 3 4 5 6 7 8 Lower spray arm Filters Rating plate Salt container Air vent Rinse aid dispenser 9 10 11 12 Detergent dispenser Cutlery basket Lower basket Upper basket 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Start button 7 Indicators 8 Option button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Drying phase. It comes on when the drying phase operates.
ENGLISH Indicator 7 Description Salt indicator. It is always off while the programme operates. 5.
www.aeg.com Programme 1) Water (l) Energy (kWh) Duration (min) 7 - 12 0.7 - 1.5 45 - 160 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 4 0.1 14 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes For all the necessary information for test performance, send an email to: info.test@dishwasher-production.
ENGLISH 9 Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
www.aeg.com How to deactivate the rinse aid empty notification • The indicators The appliance must be in programme selection mode. • The indicator continues to flash. • The display shows the current setting: 1. To enter the user mode, press and hold simultaneously Delay and Start until the indicators , , and start to flash and the display is blank. 2. Press Option. • The indicators , and and – = Acoustic signal off. – = Acoustic signal on. 3. Press Delay to change the setting. 4.
ENGLISH until the indicators , , and start to flash and the display is blank. 2. Press Start. • The indicators , and go off. 11 • The display shows the current setting: = AirDry activated. 3. Press Start to change the setting: = AirDry deactivated. 4. Press the on/off button to confirm the setting. • The indicator continues to flash. 7. OPTIONS Desired options must be activated every time before you start a programme.
www.aeg.com 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
ENGLISH CAUTION! Only use rinse aid specifically designed for dishwashers. 13 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity).
www.aeg.com Starting a programme 1. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 2. Close the appliance door. 3. Press Program again and again until the indicator of the programme you want to select comes on. The display shows the programme duration. 4. Set the applicable options. 5. Press Start to start the programme. • The washing phase indicator comes on . • The programme duration starts to decrease with steps of 1 minute.
ENGLISH 15 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
www.aeg.com • Make sure that the spray arms can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct. • The programme is applicable for the type of load and for the degree of soil.
ENGLISH 17 CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7.
www.aeg.com Authorised Service Centre, check if you can solve the problem by yourself with the help of the information in the table. WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems, the display shows an alarm code. The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre.
ENGLISH Problem and alarm code 19 Possible cause and solution The remaining time in the • This is not a defect. The appliance is working correctly. display increases and skips nearly to the end of program time. Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not levelled.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 21 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
www.aeg.com your local recycling facility or contact your municipal office.
FRANÇAIS 23 TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ............................................................................ 24 2. CONSIGNES DE SÉCURITÉ................................................................................... 25 3. DESCRIPTION DE L'APPAREIL.............................................................................. 27 4. BANDEAU DE COMMANDE ................................................................................ 28 5. PROGRAMMES...............................
1. www.aeg.com INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • • • 25 Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
www.aeg.com électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
FRANÇAIS 3.
www.aeg.com 4. BANDEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Touche Program Voyants de programme Affichage Touche Delay 3 4 7 5 6 6 Touche Start 7 Voyants 8 Touche Option 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant TimeSaver. Voyant XtraDry. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme.
FRANÇAIS 29 5.
www.aeg.com Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 7 - 12 0.7 - 1.5 45 - 160 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 4 0.1 14 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut 31 vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage.
www.aeg.com Le liquide de rinçage est automatiquement libéré au cours de la phase de rinçage chaud. Lorsque le réservoir du liquide de rinçage est vide, l'indicateur du liquide de rinçage apparaît pour vous indiquer qu'il doit être rempli. Si vous utilisez des pastilles tout en 1 contenant un agent de rinçage et que vous êtes satisfait des résultats du séchage, vous pouvez désactiver la notification de remplissage du liquide de rinçage.
FRANÇAIS Durant la phase de séchage, un dispositif ouvre la porte de l'appareil. Elle est alors maintenue entrouverte. ATTENTION! Ne tentez pas de refermer la porte de l'appareil dans les 2 minutes suivant son ouverture automatique. Vous risqueriez d'endommager l'appareil. L'option AirDry est automatiquement activée avec tous les programmes, à l'exception des programmes et (si disponibles). Pour améliorer les performances de séchage, reportez-vous à l'option XtraDry ou activez l'option AirDry. 1.
www.aeg.com Si cette option n'est pas compatible avec le programme, le voyant correspondant ne s'allume pas ou clignote rapidement pendant quelques secondes, puis s'éteint. L'affichage indique la durée du programme réactualisée. 7.2 TimeSaver Cette option augmente la pression et la température de l'eau. Les phases de lavage et de séchage sont réduites. La durée totale du programme diminue d'environ 50 %. programme. Les résultats de séchage peuvent être moins satisfaisants.
FRANÇAIS 35 B A M AX 4 5. Tournez le couvercle du réservoir de sel régénérant vers la droite pour refermer le réservoir de sel régénérant. ATTENTION! De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Après avoir rempli le réservoir de sel régénérant, lancez imédiatement un programme pour éviter la corrosion. 8.
www.aeg.com 9.1 Utilisation du produit de lavage Départ d'un programme D A B 1. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 2. Fermez la porte de l'appareil. 3. Appuyez sur Program à plusieurs reprises jusqu'à ce que le voyant du programme que vous souhaitez sélectionner s'allume. L'affichage indique la durée du programme. 4. Sélectionnez les options compatibles. 5. Appuyez sur la touche Start pour lancer le programme.
FRANÇAIS Durant la phase de séchage, si la porte est ouverte pendant plus de 30 secondes, le programme en cours s'arrête. Ceci ne se produit pas si la porte est ouverte par la fonction AirDry. Ne tentez pas de refermer la porte dans les 2 minutes suivant son ouverture automatique par la fonction AirDry car vous pourriez endommager l'appareil. Si par la suite vous refermez la porte pendant 3 minutes, le programme en cours se termine.
www.aeg.com 10.2 Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil.
FRANÇAIS 10.6 Déchargement des paniers 39 2. Commencez par décharger le panier inférieur, puis le panier supérieur. À la fin du programme, il peut rester de l'eau sur les parois et la porte de l'appareil. 1. Attendez que la vaisselle refroidisse avant de la retirer de l'appareil. La vaisselle encore chaude est sensible aux chocs. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
www.aeg.com bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le vers la droite jusqu'à la butée.
FRANÇAIS 41 La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé. Problème et code d'alarme Cause et solution possibles L'appareil ne s'allume pas. • Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. • Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles. Le programme ne démarre pas. • Vérifiez que la porte de l'appareil est fermée. • Appuyez sur Start.
www.aeg.com Problème et code d'alarme Cause et solution possibles Le temps restant sur l'affichage augmente et passe presque instantanément à la fin du programme. • Ceci est normal. L'appareil fonctionne correctement. Petite fuite au niveau de la porte de l'appareil. • L'appareil n'est pas de niveau. Desserrez ou serrez les pieds réglables (si disponibles). • La porte de l'appareil n'est pas centrée avec la cuve. Réglez le pied arrière (si disponible). La porte de l'appareil est difficile à fermer.
FRANÇAIS 43 Problème Cause et solution possibles Résultats de séchage insatisfaisants. • La vaisselle est restée trop longtemps à l'intérieur de l'appareil, porte fermée. • Il n'y a pas de liquide de rinçage ou le dosage du liquide de rinçage n'est pas suffisant. Augmentez le niveau de distributeur de liquide de rinçage. • Les articles en plastiques peuvent avoir besoin d'être essuyés. • Pour de meilleures performances de séchage, activez l'option XtraDry et réglez AirDry.
www.aeg.com Problème Cause et solution possibles Il y a des résidus de produit de lavage dans le distributeur de produit à la fin du programme. • La pastille de détergent est restée coincée dans le distributeur de produit de lavage et n'a donc pas été entièrement éliminée par l'eau. • L'eau ne peut pas éliminer le produit de lavage du distributeur. Assurez-vous que le bras d'aspersion n'est pas bloqué ou obstrué.
FRANÇAIS Pression de l'arrivée d'eau Min. / max. bar (MPa) Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.10 45 0.5 (0.05) / 8 (0.8) 1) Reportez-vous à la plaque signalétique pour d'autres valeurs.
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE.........................................................................................47 2. SICHERHEITSANWEISUNGEN.............................................................................. 48 3. GERÄTEBESCHREIBUNG.......................................................................................50 4. BEDIENFELD .......................................................................................................... 51 5. PROGRAMME........
DEUTSCH 1. 47 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • • • • • • • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden.
DEUTSCH • Schließen Sie das Gerät unbedingt an eine sachgemäß installierte Schutzkontaktsteckdose an. • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose.
www.aeg.com • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in dem Gerät einschließen. 3.
DEUTSCH 51 4. BEDIENFELD 1 2 8 1 2 3 4 5 Taste „Ein/Aus“ Taste Program Programmkontrolllampen Display Taste Delay 3 4 7 5 6 6 Taste Start 7 Kontrolllampen 8 Taste Option 4.1 Kontrolllampen Kontrolllampe Beschreibung Hauptspülgang. Leuchtet während des Hauptspülgangs auf. Trockenphase. Leuchtet während der Trocknungsphase auf. Kontrolllampe TimeSaver. Kontrolllampe XtraDry. Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs. Kontrolllampe Salz.
www.aeg.com 5.
DEUTSCH 53 5.1 Verbrauchswerte Programm1) Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (min.) 9,9 0.832 240 7 - 12 0.7 - 1.5 45 - 160 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 4 0.1 14 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.
www.aeg.com Je höher der Mineralgehalt ist, um so härter ist das Wasser. Die Wasserhärte wird in gleichwertigen Einheiten gemessen. Der Enthärter muss entsprechend der Wasserhärte in Ihrem Gebiet eingestellt werden. Ihr lokales Wasserwerk kann Sie über die Wasserhärte in Ihrem Gebiet informieren. Der Wasserenthärter muss unbedingt auf die richtige Stufe eingestellt werden, um gute Spülergebnisse zu garantieren.
DEUTSCH 6.3 Klarspülmittelnachfüllanzeige Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. 55 3. Drücken Sie Option zum Ändern der Einstellung. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 6.4 Signaltöne Das Klarspülmittel wird automatisch während der heißen Spülphasen abgegeben. Bei einer Störung des Geräts ertönen akustische Signale. Es ist nicht möglich, diese Signaltöne auszuschalten.
www.aeg.com Zur Verbesserung der Trocknungsleistung beachten Sie die XtraDry-Option oder schalten Sie AirDry ein. So schalten Sie AirDry aus Das Gerät muss sich im Programmwahlmodus befinden. 1. Halten Sie zum Aufrufen des Benutzermodus gleichzeitig Delay und Start gedrückt, bis die Kontrolllampen Während der Trockenphase wird die Gerätetür durch eine Vorrichtung geöffnet. Die Tür bleibt dann einen Spaltbreit geöffnet.
DEUTSCH Durch das Einschalten der Option XtraDry wird der TimeSaver ausgeschaltet und umgekehrt. So schalten Sie XtraDry ein Drücken Sie Option, bis die Kontrolllampe leuchtet. Ist die Option nicht mit dem Programm kombinierbar, leuchtet die entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. Das Display zeigt die aktualisierte Programmdauer an. 7.2 TimeSaver Wenn diese Option eingeschaltet ist, erhöht sich der Wasserdruck und die Wassertemperatur.
www.aeg.com B A M AX 4 5. Drehen Sie den Deckel des Salzbehälters im Uhrzeigersinn, um den Salzbehälter zu schließen. VORSICHT! Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Starten Sie nach dem Füllen des Salzbehälters umgehend ein Programm, um Korrosion zu verhindern. 8.2 Füllen des KlarspülmittelDosierers A D B C 9. TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten.
DEUTSCH 9.1 Verwenden von Reinigungsmittel • Nach 5 Minuten, wenn das Programm nicht gestartet wurde. Starten eines Programms D A B 1. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. 2. Schließen Sie die Gerätetür. 3. Drücken Sie Program wiederholt, bis die Kontrolllampe des gewünschten Programms leuchtet. Im Display wird die Programmdauer angezeigt. 4. Stellen Sie die verfügbaren Optionen ein. 5.
www.aeg.com Wenn die Tür während der Trockenphase länger als 30 Sekunden geöffnet wird, wird das laufende Programm beendet. Dies geschieht nicht, wenn die Tür durch die Funktion AirDry geöffnet wird. Versuchen Sie nicht, die Gerätetür innerhalb der ersten 2 Minuten nach der automatischen Öffnung durchAirDry zu schließen, da das Gerät beschädigt werden könnte. Wird die Tür danach für weitere 3 Minuten geschlossen, wird das laufende Programm beendet.
DEUTSCH • Wir empfehlen in Bereichen mit hartem und sehr hartem Wasser Reinigungsmittel ohne Zusätze (Pulver, Gel oder Tabs ohne Zusätze), Klarspülmittel und Salz getrennt zu verwenden, um optimale Reinigungsund Trocknungsergebnisse zu erzielen. • Schalten Sie das Gerät mindestens einmal im Monat mit einem Geschirrspülerreinigungsmittel, das speziell für diesen Zweck vorgesehen ist, ein. • Geschirrspüler-Tabs lösen sich bei kurzen Programmen nicht vollständig auf.
www.aeg.com Am Programmende kann sich noch Wasser an den Seitenwänden und der Gerätetür befinden. 11. REINIGUNG UND PFLEGE WARNUNG! Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden. Verschmutzte Filter und verstopfte Sprüharme beeinträchtigen das Spülergebnis. Prüfen Sie die Filter regelmäßig und reinigen Sie diese, falls nötig. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 11.
DEUTSCH 63 sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger. • Benutzen Sie keine Scheuermittel, scheuernde Reinigungsschwämmchen oder Lösungsmittel. 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet.
www.aeg.com Bei manchen Störungen zeigt das Display einen Alarmcode an. der autorisierte Kundendienst gerufen werden muss. Die meisten Störungen, die auftreten, können behoben werden, ohne dass Störung und Alarmcode Mögliche Ursache und Abhilfe Das Gerät lässt sich nicht einschalten. • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. Das Programm startet nicht.
DEUTSCH 65 Störung und Alarmcode Mögliche Ursache und Abhilfe Die verbleibende Zeit im Display erhöht sich und springt bis kurz vor die Programmende-Zeit. • Dies ist keine Störung. Das Gerät arbeitet ordnungsgemäß. Aus der Gerätetür tritt ein wenig Wasser aus. • Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden). • Die Gerätetür ist nicht mittig zur Wanne positioniert. Stellen Sie den hinteren Fuß ein (sofern vorhanden).
www.aeg.com Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät. • Es ist kein Klarspülmittel vorhanden oder die Klarspülmittelmenge ist nicht ausreichend. Stellen Sie den Klarspülmittel-Dosierer auf eine höhere Einstellung. • Kunststoffteile müssen eventuell mit einem Tuch abgetrocknet werden. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen.
DEUTSCH 67 Störung Mögliche Ursache und Abhilfe Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen. • Das Wasser kann das Reinigungsmittel nicht aus dem Behälter ausspülen. Achten Sie darauf, dass der Sprüharm nicht blockiert oder verstopft ist. • Stellen Sie sicher, dass die im Korb eingeordneten Gegenstände ein Öffnen des Reinigungsmittelbehälters nicht verhindern.
www.aeg.com Wasserversorgung Kalt- oder Warmwasser 2) max. 60 °C Fassungsvermögen Maßgedecke 13 Leistungsaufnahme Ein-Zustand (W) 5.0 Leistungsaufnahme Aus-Zustand (W) 0.10 1) Weitere Angaben finden Sie auf dem Typenschild. 2) Wenn Sie Heißwasser mit umweltfreundlichen, alternativen Energiequellen (z. B. Solaranlagen oder Windkraft) aufbereiten, können Sie durch den Anschluss des Geräts an die Heißwasserversorgung Energie sparen. 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol .
DEUTSCH 69
www.aeg.
DEUTSCH 71
156904750-A-312016 www.aeg.