NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 24 45 FAVORIT 56602 IM0P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 3 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA’S..................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • • Als de voedingskabel beschadigd is, moet de fabrikant, een erkende serviceverlener of een gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt.
NEDERLANDS • Trek niet aan het netsnoer om het apparaat los te koppelen. Trek altijd aan de stekker. • Dit apparaat voldoet aan de EEGrichtlijnen. • Alleen voor VK en Ierland. Het apparaat heeft een stekker van 13 ampère. Als de zekering van de stekker verwisseld moet worden, gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Aan/uit-toets Programma-indicatielampjes Indicatielampjes Weergave Delay-toets ExtraHygiene-toets 7 8 9 10 XtraDry-toets Programmatoets (verder) Programmatoets (terug) Reset-toets 4.1 Indicatielampjes Aanduiding Beschrijving XtraDry-indicatielampje. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is.
www.aeg.com 5.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 4 0.1 14 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
www.aeg.com Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
NEDERLANDS 1. Om de gebruikersmodus in te voeren, drukt u tegelijkertijd totdat de lampjes en , en gaan knipperen en het display leeg is. 2. Druk op . • De indicatielampjes en gaan uit. • Het indicatielampje blijft knipperen. • Het display toont de huidige instelling: bijv. = niveau 4. – De glansmiddelniveaus lopen van 0A tot 6A. – Niveau 0 = er wordt geen glansmiddel gebruikt. 3. Druk herhaaldelijk op om de instelling te wijzigen. 4. Druk op de knop aan/uit om de instelling te bevestigen. 6.
www.aeg.com Het activeren van XtraDry Druk op XtraDry. Het bijbehorende indicatielampje gaat branden. Als de optie niet van toepassing is op het programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit. Het display geeft de bijgewerkte programmaduur weer. 7.2 ExtraHygiene Met deze optie heeft u betere hygiëneresultaten. Tijdens de spoelfase blijft de temperatuur gedurende minimaal 10 minuten op 70 °C.
NEDERLANDS LET OP! Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Start na het bijvullen van het zoutreservoir onmiddellijk een programma om corrosie te voorkomen. 8.2 Het vullen van het glansmiddeldoseerbakje A 13 1. Open het deksel (C). 2. Vul het glansmiddeldoseerbakje (B) niet verder dan de aanduiding ''MAX''. 3. Verwijder gemorst glansmiddel met een absorberend doekje om te voorkomen dat er te veel schuim ontstaat. 4. Sluit het deksel.
www.aeg.com LET OP! Gebruik uitsluitend vaatwasmiddelen die specifiek zijn bedoeld voor gebruik in vaatwassers 1. Druk op de ontgrendelknop (A) om de deksel te openen (C). 2. Doe de vaatwastablet of het poeder in het doseerbakje (B). 3. Plaats een kleine hoeveelheid van het vaatwasmiddel in de binnenkant van de deur van het apparaat als het programma een voorwasfase heeft. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. 9.
NEDERLANDS Het programma annuleren Houd tegelijkertijd Reset ingedrukt tot het apparaat in de programmakeuzemodus staat. Controleer of er afwasmiddel in het afwasmiddeldoseerbakje aanwezig is voordat u een nieuw programma start. Einde van het programma Als het programma is voltooid, wordt op het display 0:00 weergegeven. 15 Alle knoppen zijn inactief behalve de aan/uit knop. 1. Druk op de aan/uit-toets of wacht totdat de Auto Off-functie het apparaat automatisch heeft uitgeschakeld.
www.aeg.com 5. Stel de hoeveelheid glansmiddel in. 6. De aanduiding leeg glansmiddelreservoir activeren. 10.4 De korven inruimen • Gebruik het apparaat alleen om voorwerpen af te wassen die vaatwasbestendig zijn. • Doe geen voorwerpen in het apparaat die gemaakt zijn van hout, hoorn, aluminium, tin en koper. • Plaats geen voorwerpen in het apparaat die water kunnen absorberen (sponzen, keukenhanddoeken). • Verwijder alle voedselresten van de voorwerpen.
NEDERLANDS 17 C B A 1. Draai de filter (B) linksom en verwijder het. 2. Verwijder de filter (C) uit de filter (B). 3. Verwijder de platte filter (A). 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 4. Was de filters.
www.aeg.com 11.2 De bovenste sproeiarm schoonmaken We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt. naar boven in de richting van de lagere pijl en draait u hem tegelijkertijd tegen de wijzers van de klok in, zodat hij op zijn plek vergrendelt. Verstopte gaten kunnen onbevredigende wasresultaten opleveren. 1. Trek het bovenrek naar buiten. 2.
NEDERLANDS WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. 19 Bij sommige problemen wordt er op de display een alarmcode weergegeven. Het merendeel van de problemen die ontstaan kunnen worden opgelost zonder contact op te nemen met een erkend servicecentrum. Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing Kleine lekkage uit de deur van het apparaat. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • De deur van het apparaat is niet gecentreerd op de kuip. Verstel de achterpoot (indien van toepassing). De deur van het apparaat sluit moeilijk. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • Delen van het serviesgoed steken uit de korven.
NEDERLANDS 21 Probleem Mogelijke oorzaak en oplossing Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan. • Het glansmiddel is op of de dosering van glansmiddel is niet voldoende. Stel de dosering van het glansmiddel in op een hogere stand. • Plastic voorwerpen moeten mogelijk met een doek worden afgedroogd. • Activeer voor de beste droogprestatie de optie XtraDry. • We raden aan altijd glansmiddel te gebruiken, zelfs in combinatie met wastabletten.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water. middeldoseerbakje. • Het water kan het vaatwasmiddel niet uit het vaatwasmiddeldoseerbakje spoelen. Zorg ervoor dat de bovenste sproeiarm niet geblokkeerd of verstopt is.
NEDERLANDS Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.10 23 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door een alternatieve, milieuvriendelijkere energiebron geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14. MILIEUBESCHERMING Recycle de materialen met het symbool . Gooi de verpakking in een geschikte verzamelcontainer om het te recyclen.
www.aeg.com CONTENTS 1. SAFETY INFORMATION........................................................................................... 25 2. SAFETY INSTRUCTIONS...........................................................................................26 3. PRODUCT DESCRIPTION.........................................................................................28 4. CONTROL PANEL..................................................................................................... 29 5. PROGRAMMES......
ENGLISH 1. 25 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH 27 • Ensure that there are no visible water leaks during and after the first use of the appliance. • The water inlet hose has a safety valve and a sheath with an inner mains cable. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed. There can be detergent on the dishes.
www.aeg.com 3.
ENGLISH 4. CONTROL PANEL 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 On/off button Programme indicators Indicators Display Delay button ExtraHygiene button 7 8 9 10 XtraDry button Programme button (forward) Programme button (backward) Reset button 4.1 Indicators Indicator Description XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. ExtraHygiene indicator. 5.
www.aeg.
ENGLISH Programme 1) Water (l) Energy (kWh) Duration (min) 4 0.1 14 31 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes info.test@dishwasher-production.com For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level.
ENGLISH 3. Press again and again to change the setting. 4. Press the on/off button to confirm the setting. 6.4 The rinse aid empty notification The rinse aid helps to dry the dishes without streaks and stains. The rinse aid is automatically released during the hot rinse phase. When rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid.
www.aeg.com How to activate ExtraHygiene Press ExtraHygiene, the related indicator comes on If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated programme duration. 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 35 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. If you use multi-tablets and the drying performance is satisfactory, the rinse aid refill indication can be disabled.
www.aeg.com detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the lid locks into position. 9.2 Setting and starting a programme The Auto Off function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. Starting a programme 1. Keep the appliance door ajar. 2.
ENGLISH If you open the door before the activation of Auto Off, the appliance is automatically deactivated. 37 2. Close the water tap. 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase.
www.aeg.com • Make sure that cutlery and dishes do not bond together. Mix spoons with other cutlery. • Make sure that glasses do not touch other glasses. • Put small items in the cutlery basket. • Put light items in the upper basket. Make sure that the items do not move. • Make sure that the spray arm can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • There is dishwasher salt and rinse aid (unless you use multi- tablets).
ENGLISH 39 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 5.
www.aeg.com 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth.
ENGLISH 41 Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The program does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener.
www.aeg.com Problem and alarm code Possible cause and solution Rattling/knocking sounds from inside the appliance. • The tableware is not properly arranged in the baskets. Refer to basket loading leaflet. • Make sure that the spray arms can rotate freely. The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use.
ENGLISH 43 Problem Possible cause and solution The dishes are wet. • For the best drying performance activate the option XtraDry. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
www.aeg.com Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818 - 898 / 575 Electrical connection 1) Voltage (V) 200 - 240 Frequency (Hz) 50 / 60 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.
FRANÇAIS 45 TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................46 2. CONSIGNES DE SÉCURITÉ......................................................................................47 3. DESCRIPTION DE L'APPAREIL.................................................................................49 4. BANDEAU DE COMMANDE....................................................................................50 5. PROGRAMMES.......................
1. www.aeg.com INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • • • 47 Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
www.aeg.com changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
FRANÇAIS 3.
www.aeg.com 4. BANDEAU DE COMMANDE 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Touche Marche/Arrêt Voyants de programme Voyants Affichage Touche Delay Touche ExtraHygiene 7 8 9 10 Touche XtraDry Touche Programme (avant) Touche Programme (arrière) Touche Reset 4.1 Voyants Indicateur Description Voyant XtraDry. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de sel régénérant.
FRANÇAIS 51 5.
www.aeg.com Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 7 - 14 0.6 - 1.4 40 - 150 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 4 0.1 14 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région. Il est important de régler 53 l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage. Dureté eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.
www.aeg.com Vous pouvez définir la quantité de liquide de rinçage libérée entre le niveau 1 (quantité minimale) et le niveau 6 (quantité maximale). Le dosage 0 désactive le distributeur de liquide de rinçage et le liquide de rinçage n'est pas diffusé. Réglage d'usine : niveau 4. Comment régler le niveau de liquide de rinçage L'appareil doit être en mode Programmation. 1.
FRANÇAIS 55 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver ces options pendant le déroulement d'un programme. 7.1 XtraDry Activez cette option lorsque vous voulez améliorer les performances de séchage. En utilisant cette option, la durée de certains programmes, la consommation d'eau et la température du dernier rinçage peuvent être affectés.
www.aeg.com 2. Versez 1 litre d'eau dans le réservoir de sel régénérant (uniquement la première fois). 3. Remplissez le réservoir avec du sel régénérant. 4. Enlevez le sel qui se trouve autour de l'ouverture du réservoir de sel régénérant. 8.2 Comment remplir le distributeur de liquide de rinçage A B C ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. 5.
FRANÇAIS 57 Si vous utilisez des pastilles de détergent multifonctions et que les performances du séchage sont satisfaisantes, l'indication de remplissage du liquide de rinçage peut être désactivée. Pour de meilleures performances de séchage, nous vous recommandons de toujours utiliser du liquide de rinçage, même si vous utilisez déjà des pastilles tout-en-1 contenant un agent de rinçage. 9. UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil.
www.aeg.com Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3. Appuyez sur ou pour sélectionner un programme. • Le voyant du programme sélectionné clignote. • L'affichage indique la durée du programme. 4. Sélectionnez les options compatibles. 5. Fermez la porte de l'appareil pour démarrer le programme.
FRANÇAIS 59 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable. En cas de besoin, utilisez le programme de prélavage (si disponible) ou sélectionnez un programme avec une phase de prélavage. • Utilisez toujours tout l'espace des paniers.
www.aeg.com • Ne mettez pas dans le lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre. • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage). • Enlevez les restes d'aliments sur les articles. • Laissez tremper les casseroles contenant des restes d'aliments brûlés. • Chargez les articles creux (tasses, verres et casseroles) en les retournant.
FRANÇAIS 61 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 5.
www.aeg.com 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices.
FRANÇAIS problème par vous-même à l'aide des informations du tableau. AVERTISSEMENT! Des réparations mal entreprises peuvent entraîner un grave danger pour l'utilisateur. Toute réparation ne doit être effectuée que par un technicien qualifié. 63 Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé. Problème et code d'alarme Cause et solution possibles L'appareil ne s'allume pas.
www.aeg.com Problème et code d'alarme Cause et solution possibles Le programme dure trop longtemps. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte. Le temps restant sur l'affi• Ceci est normal. L'appareil fonctionne correctement. chage augmente et passe presque instantanément à la fin du programme. Petite fuite au niveau de la porte de l'appareil. • L'appareil n'est pas de niveau. Desserrez ou serrez les pieds réglables (si disponibles).
FRANÇAIS 65 Problème Cause et solution possibles Résultats de séchage insatisfaisants. • La vaisselle est restée trop longtemps à l'intérieur de l'appareil, porte fermée. • Il n'y a pas de liquide de rinçage ou le dosage du liquide de rinçage n'est pas suffisant. Augmentez le niveau de distributeur de liquide de rinçage. • Les articles en plastiques peuvent avoir besoin d'être essuyés. • Pour de meilleures performances de séchage, activez l'option XtraDry.
www.aeg.com Problème Cause et solution possibles Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble. Évitez de placer les couverts en argent et en acier inoxydable les uns à côté des autres. Il y a des résidus de produit de lavage dans le distributeur de produit à la fin du programme.
FRANÇAIS 67 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818 - 898 / 575 Branchement électrique1) Tension (V) 200 - 240 Fréquence (Hz) 50 / 60 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.
117900254-A-392016 www.aeg.