NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 23 43 FAVORIT 56602 ID0P FAVORIT 56602 IM0P FAVORIT 56602 IW0P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant. 2.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Aan/uit-toets Programma-indicatielampjes Indicatielampjes Weergave Delay-toets ExtraHygiene-toets 7 8 9 10 Multitab-toets Programmatoets (verder) Programmatoets (terug) Reset-toets 4.1 Indicatielampjes Aanduiding Omschrijving Multitab-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is.
www.aeg.com 5.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 4 0.1 14 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
www.aeg.com Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
NEDERLANDS • Het display toont de huidige instelling: bijv. = niveau 4. – De glansmiddelniveaus lopen van 0A tot 6A. – Niveau 0 = er wordt geen glansmiddel gebruikt. om de 3. Druk herhaaldelijk op instelling te wijzigen. 4. Druk op de knop aan/uit om de instelling te bevestigen. 6.4 Gebruik van glansmiddel en multitabletten De fabrieksinstelling voor het glansmiddeldoseerbakje wordt met het doseerbakje geactiveerd. Dit betekent dat het glansmiddeldoseerbakje altijd glansmiddel vrij laat komen.
www.aeg.com Multitab is geen permanente optie en moet elke cyclus geselecteerd worden. Multitab activeren Druk op Multitab. Het bijbehorende indicatielampje gaat branden. 7.2 ExtraHygiene Met deze optie heeft u betere hygiëneresultaten. Tijdens de spoelfase blijft de temperatuur gedurende minimaal 10 minuten op 70 °C. ExtraHygiene activeren Druk op ExtraHygiene, het bijbehorende indicatielampje gaat nu branden.
NEDERLANDS Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Gevaar voor roest. Start om dit te voorkomen een programma nadat u het zoutreservoir heeft bijgevuld. 8.2 Het vullen van het glansmiddeldoseerbakje A B 13 LET OP! Gebruik alleen glansspoelmiddel voor afwasautomaten. 1. Open het deksel (C). 2. Vul het glansmiddeldoseerbakje (B) niet verder dan de aanduiding ''MAX''. 3. Verwijder gemorst glansmiddel met een absorberend doekje om te voorkomen dat er te veel schuim ontstaat.
www.aeg.com LET OP! Gebruik uitsluitend vaatwasmiddelen die specifiek zijn bedoeld voor gebruik in vaatwassers 1. Druk op de ontgrendelknop (A) om de deksel te openen (C). 2. Doe de vaatwastablet of het poeder in het doseerbakje (B). 3. Plaats een kleine hoeveelheid van het vaatwasmiddel in de binnenkant van de deur van het apparaat als het programma een voorwasfase heeft. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. 9.
NEDERLANDS Het programma annuleren Houd tegelijkertijd Reset ingedrukt tot het apparaat in de programmakeuzemodus staat. Controleer of er afwasmiddel in het afwasmiddeldoseerbakje aanwezig is voordat u een nieuw programma start. Einde van het programma Als het programma is voltooid, wordt op het display 0:00 weergegeven. 15 Alle knoppen zijn inactief behalve de aan/uit knop. 1. Druk op de aan/uit-toets of wacht totdat de Auto Off-functie het apparaat automatisch heeft uitgeschakeld.
www.aeg.com 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4.
NEDERLANDS 17 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
www.aeg.com 11.2 De bovenste sproeiarm schoonmaken We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt. naar boven in de richting van de lagere pijl en draait u hem tegelijkertijd tegen de wijzers van de klok in, zodat hij op zijn plek vergrendelt. Verstopte gaten kunnen onbevredigende wasresultaten opleveren. 1. Trek het bovenrek naar buiten. 2.
NEDERLANDS WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. 19 Bij sommige problemen wordt er op de display een alarmcode weergegeven. Het merendeel van de voorkomende problemen kan worden opgelost zonder contact op te hoeven nemen met een erkend servicecentrum. Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing De resterende duur in het display wordt verlengd en schakelt bijna naar het eind van de programmaduur. • Dit is geen storing. Het apparaat werkt goed. Weinig lekkage uit de deur van het apparaat. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • De deur van het apparaat is niet gecentreerd op de kuip. Verstel de achterpoot (indien van toepassing). De deur van het apparaat sluit moeilijk.
NEDERLANDS 21 Probleem Mogelijke oorzaak en oplossing Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan. • Het glansmiddel is op of de dosering van glansmiddel is niet voldoende. Stel de dosering van het glansmiddel in op een hogere stand. • Plastic voorwerpen moeten mogelijk met een doek worden afgedroogd. Witte strepen of een blauwe waas op glazen en serviesgoed. • De vrijgegeven hoeveelheid glansmiddel is te hoog.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Kalkresten op het serviesgoed, op de kuip en aan de binnenkant van de deur. • Zie 'De waterontharder instellen'. Dof, ontkleurd of afgeschilverd serviesgoed. • Zorg dat alleen vaatwasmachinebestendige voorwerpen in het apparaat worden gewassen. • Laad de korf voorzichtig in en uit. Raadpleeg de folder laden van de korf. • Leg tere voorwerpen in het bovenrek.
ENGLISH 23 CONTENTS 1. SAFETY INFORMATION.........................................................................................24 2. SAFETY INSTRUCTIONS........................................................................................ 25 3. PRODUCT DESCRIPTION...................................................................................... 26 4. CONTROL PANEL...................................................................................................27 5. PROGRAMMES....................
1. www.aeg.com SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
ENGLISH • • • • • • 25 Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
www.aeg.com WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
ENGLISH 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Cutlery basket 11 Lower basket 12 Upper basket 4. CONTROL PANEL 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 On/off button Programme indicators Indicators Display Delay button ExtraHygiene button 7 8 9 10 Multitab button Programme button (forward) Programme button (backward) Reset button 4.1 Indicators Indicator Description Multitab indicator. Salt indicator. It is always off while the programme operates.
www.aeg.com 5.
ENGLISH Programme 1) Water (l) Energy (kWh) Duration (min) 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 4 0.1 14 29 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes info.test@dishwasher-production.com For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level.
ENGLISH – Level 0 = no rinse aid is released. 3. Press again and again to change the setting. 4. Press the on/off button to confirm the setting. How to deactivate the rinse aid dispenser The appliance must be in programme selection mode. 1. To enter the user mode, press and 6.4 Use of rinse aid and multitablets hold simultaneously The factory setting of the rinse aid dispenser is with the dispenser activated. This means that the rinse aid dispenser always releases rinse aid. blank.
www.aeg.com How to activate ExtraHygiene Press ExtraHygiene, the related indicator comes on If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated programme duration. 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 33 CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. C 9. DAILY USE 1. Open the water tap. 2.
www.aeg.com Starting a programme 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press or to select a programme. • The indicator of the selected programme flashes. • The display shows the programme duration. 4. Set the applicable options. 5. Close the appliance door to start the programme. • The programme indicator stops flashing and comes on with fixed light.
ENGLISH 35 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
www.aeg.com • Put light items in the upper basket. Make sure that the items do not move. • Make sure that the spray arm can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct.
ENGLISH 37 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 1. Pull out the upper basket. 2.
www.aeg.com 11.4 Internal cleaning 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance.
ENGLISH 39 Problem and alarm code Possible cause and solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows . The appliance does not drain the water.
www.aeg.com Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
ENGLISH 41 Problem Possible cause and solution There are residues of detergent in the dispenser at the end of the program. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water. • Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged. • Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening. Odours inside the appliance. • Refer to "Internal cleaning".
www.aeg.com 14. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
FRANÇAIS 43 TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 44 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 45 3. DESCRIPTION DE L'APPAREIL.............................................................................. 47 4. BANDEAU DE COMMANDE................................................................................. 48 5. PROGRAMMES.............................
1. www.aeg.com CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • • • 45 Respectez le nombre maximum de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
www.aeg.com • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
FRANÇAIS 3.
www.aeg.com 4. BANDEAU DE COMMANDE 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Touche Marche/Arrêt Voyants de programme Voyants Affichage Touche Delay Touche ExtraHygiene 7 8 9 10 Touche Multitab Touche Programme (avant) Touche Programme (arrière) Touche Reset 4.1 Voyants Voyant Description Voyant Multitab. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage.
FRANÇAIS 49 5.
www.aeg.com Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 7 - 14 0.6 - 1.4 40 - 150 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 4 0.1 14 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région. Il est important de régler 51 l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage. Dureté de l'eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.
www.aeg.com Comment régler le niveau de liquide de rinçage L'appareil doit être en mode Programmation. 1. Pour entrer en mode utilisateur, et maintenez les touches enfoncées jusqu'à ce que les voyants , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. . et • Le voyant continue à clignoter. • L'affichage indique le réglage actuel : Par ex., = niveau 4. – Les niveaux de liquide de rinçage s'échelonnent de 0A à 6A.
FRANÇAIS 53 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver ces options pendant le déroulement d'un programme. 7.1 Multitab Activez cette option lorsque vous utilisez des pastilles tout-en-un contenant le sel régénérant, le liquide de rinçage et le produit de lavage. Elles peuvent également contenir d'autres agents de lavage ou de rinçage. Cette option désactive la libération du sel régénérant.
www.aeg.com Le sel permet de recharger la résine dans l'adoucisseur d'eau et de garantir de bons résultats de lavage en utilisation quotidienne. 8.2 Comment remplir le distributeur de liquide de rinçage Remplissage du réservoir de sel régénérant A B 1. Tournez le couvercle du réservoir de sel régénérant vers la gauche et retirez-le. 2. Versez 1 litre d'eau dans le réservoir de sel régénérant (uniquement la première fois). 3. Remplissez le réservoir avec du sel régénérant.
FRANÇAIS Assurez-vous que l'appareil est en mode Programmation. • Si le voyant du réservoir de sel régénérant est allumé, remplissez le réservoir. • Si le voyant du liquide de rinçage est allumé, remplissez le distributeur de liquide de rinçage. 3. Chargez les paniers. 4. Ajoutez le produit de lavage. Si vous utilisez des pastilles de détergent tout en 1, activez l'option Multitab. 5. Réglez et lancez le programme adapté au type de vaisselle et au degré de salissure. 9.
www.aeg.com Le voyant du programme sélectionné continue à clignoter. 3. Fermez la porte de l'appareil pour démarrer le décompte. Le voyant de programme s'arrête de clignoter et s'allume en continu. • Lorsque le décompte est terminé, le programme démarre. • Pendant le décompte, seules les touches Reset et Delay sont actives. Vous ne pouvez pas modifier le programme ou les options.
FRANÇAIS degré de salissure. Le programme ECO vous permet d'optimiser votre consommation d'eau et d'énergie pour la vaisselle et les couverts normalement sales. 10.2 Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil.
www.aeg.com • Assurez-vous que le bras d'aspersion tourne librement avant de lancer un programme. 10.5 Avant le démarrage d'un programme Assurez-vous que : • Les filtres sont propres et correctement installés. • Le bouchon du réservoir de sel régénérant est vissé. • Les bras d'aspersion ne sont pas obstrués. • Vous avez utilisé du sel régénérant et du liquide de rinçage (sauf si vous utilisez des pastilles tout en 1). • La vaisselle est bien positionnée dans les paniers.
FRANÇAIS 59 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur Nous vous conseillons de nettoyer régulièrement le bras d'aspersion supérieur afin d'éviter que ses orifices ne se bouchent.
www.aeg.com toutes les particules de saleté incrustées dans les orifices. 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur 4.
FRANÇAIS 61 Problème et code d'alarme Cause et solution possibles L'appareil ne s'allume pas. • Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. • Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles. Le programme ne démarre pas. • Vérifiez que la porte de l'appareil est fermée. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte.
www.aeg.com Problème et code d'alarme Cause et solution possibles La porte de l'appareil est difficile à fermer. • L'appareil n'est pas de niveau. Desserrez ou serrez les pieds réglables (si disponibles). • De la vaisselle dépasse des paniers. Bruit de cliquetis ou de battement à l'intérieur de l'appareil. • La vaisselle n'est pas correctement rangée dans les paniers. Reportez-vous au manuel de chargement du panier. • Assurez-vous que les bras d'aspersion peuvent tourner librement.
FRANÇAIS 63 Problème Cause et solution possibles Il y a des taches et traces de gouttes d'eau séchées sur les verres et la vaisselle. • La quantité de liquide de rinçage libérée n'est pas suffisante. Placez le sélecteur de dosage du liquide de rinçage sur un niveau plus élevé. • Il se peut que la qualité du liquide de rinçage soit en cause. La vaisselle est mouillée. • Le programme ne contient pas de phase de séchage ou une phase de séchage à basse température.
www.aeg.com Problème Cause et solution possibles Vaisselle ternie, décolorée ou ébréchée. • Assurez-vous de ne placer dans l'appareil que des articles adaptés au lave-vaisselle. • Chargez et déchargez le panier avec précautions. Reportez-vous au manuel de chargement du panier. • Placez les objets délicats dans le panier supérieur. Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 13.
FRANÇAIS 65
www.aeg.
FRANÇAIS 67
117900252-A-052015 www.aeg.