NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 22 40 FAVORIT 65709 VI0P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • Het apparaat moet met de nieuwe slangset worden aangesloten op een kraan. Oude slangsets mogen niet opnieuw worden gebruikt. 1.
NEDERLANDS stekker verwisseld moet worden, gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant. 2.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Top sproeiarm Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 Beam-on-Floor De Beam-on-Floor is een lichtstraal die op de keukenvloer onder de deur van het apparaat verschijnt. • Wanneer het programma start, gaat de rode lichtstraal aan. De lichtstraal blijft gedurende het volledige programma zichtbaar. • Wanneer het programma is voltooid, gaat het groene lampje branden.
NEDERLANDS 4. BEDIENINGSPANEEL 1 1 2 3 4 5 2 Aan/uit-toets Weergave Delay-toets Program-toets ProBoost-toets 3 4 6 7 8 9 5 6 7 8 9 TimeSaver-toets Multitab-toets RESET-toets Indicatielampjes 4.1 Indicatielampjes Aanduiding Omschrijving Einde-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. 5.
www.aeg.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) P2 7 - 14 0.6 - 1.4 40 - 150 P3 14 - 16 1.2 - 1.5 139 - 149 P4 12.5 - 14.5 1.4 - 1.6 154 - 164 P5 12 - 14 0.7 - 0.9 75 - 85 P6 9.5 - 10.5 1.10 - 1.30 55 - 65 P7 10 0.9 30 P8 9 - 10 1.0 - 1.2 219 - 229 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.
www.aeg.com programmakeuzemodus op de volgende manier instellen: waterhardheid wordt gemeten in de volgende gelijkwaardige schalen. Houd tegelijkertijd RESET ingedrukt tot het apparaat in de programmakeuzemodus staat. De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten. 6.
NEDERLANDS 6.3 Het glansmiddeldoseerbakje Het is mogelijk het glansmiddeldoseerbakje te deactiveren. In dit geval laat het doseerbakje geen glansmiddel vrijkomen mits de optie Multitab wordt geactiveerd. Met glansmiddel wordt het serviesgoed zonder vlekken of strepen gedroogd. Het glansmiddel wordt automatisch vrijgegeven tijdens de warme spoelfase. U kunt de vrij te geven hoeveelheid glansmiddel instellen tussen stand 1 (laagste hoeveelheid) en stand 6 (hoogste hoeveelheid).
www.aeg.com Na het beëindigen van het programma klinkt er tevens een geluidssignaal. Dit geluidssignaal is standaard uitgeschakeld, maar kan worden geactiveerd. • De indicatielampjes instelling: uit. 3. Druk op wijzigen. Het apparaat moet in de programmakeuzemodus staan. = Geluidssignaal om de instelling te = Geluidssignaal aan. 4. Druk op de knop aan/uit om de instelling te bevestigen. 1.
NEDERLANDS De wasresultaten zijn hetzelfde als bij de normale programmaduur. De droogresultaten nemen mogelijk iets af. TimeSaver activeren Druk op . Het bijbehorende indicatielampje gaat nu branden. Als de optie niet van toepassing is op het programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit. Het display geeft de bijgewerkte programmaduur weer. 13 De wasresultaten zijn ook heel goed bij zwaar vervuild wasgoed.
www.aeg.com LET OP! Gebruik alleen glansspoelmiddel voor afwasautomaten. 5. Draai de dop van het zoutreservoir rechtsom om het zoutreservoir te sluiten. Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Gevaar voor roest. Start om dit te voorkomen een programma nadat u het zoutreservoir heeft bijgevuld. 1. Open het deksel (C). 2. Vul het glansmiddeldoseerbakje (B) niet verder dan de aanduiding ''MAX''. 3.
NEDERLANDS 9.1 Vaatwasmiddel gebruiken A B C LET OP! Gebruik uitsluitend vaatwasmiddelen die specifiek zijn bedoeld voor gebruik in vaatwassers 1. Druk op de ontgrendelknop (A) om de deksel te openen (C). 2. Doe de vaatwastablet of het poeder in het doseerbakje (B). 3. Plaats een kleine hoeveelheid van het vaatwasmiddel in de binnenkant van de deur van het apparaat als het programma een voorwasfase heeft. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. 9.
www.aeg.com De uitgestelde start annuleren tijdens het aftellen Als u de uitgestelde start annuleert, moet u het programma en de opties opnieuw instellen. Houd tegelijkertijd RESET ingedrukt tot het apparaat in de programmakeuzemodus staat. Controleer of er afwasmiddel in het afwasmiddeldoseerbakje aanwezig is voordat u een nieuw programma start. Einde van het programma Wanneer het programma is voltooid en u opent de deur, wordt het apparaat automatisch uitgeschakeld. Draai de waterkraan dicht.
NEDERLANDS 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4. Als het programma is voltooid, wijzigt u de waterontharder in de waterhardheid van uw omgeving. 5.
www.aeg.com 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
NEDERLANDS 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 19 11.
www.aeg.com Probleem en alarmcode Mogelijke oplossing De anti-overstromingsbevei- • Draai de waterkraan dicht en neem contact op met de liging is aan. klantenservice. Op het display verschijnt . Schakel het apparaat na controle aan en uit. Als het probleem opnieuw optreedt, neemt u contact op met onze klantenservice. Voor alarmcodes die niet in de tabel vermeld zijn, neemt u contact op met de klantenservice. 12.
NEDERLANDS Vermogen Couverts 15 Energieverbruik Modus aan laten (W) 0.99 Energieverbruik Uit-modus (W) 0.10 21 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door een alternatieve, milieuvriendelijkere energiebron geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14. MILIEUBESCHERMING Recycle de materialen met het symbool . Gooi de verpakking in een geschikte verzamelcontainer om het te recyclen.
www.aeg.com CONTENTS 1. SAFETY INFORMATION.........................................................................................23 2. SAFETY INSTRUCTIONS........................................................................................ 24 3. PRODUCT DESCRIPTION...................................................................................... 25 4. CONTROL PANEL...................................................................................................26 5. PROGRAMMES................
ENGLISH 1. 23 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com 1.2 Children and vulnerable people safety • • • • • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Do not let children play with the appliance. Keep all detergents away from children.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
www.aeg.com 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Lower basket 11 Upper basket 12 Cutlery drawer 3.1 Beam-on-Floor • When the appliance has a malfunction, the red light flashes. The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door. The Beam-on-Floor goes off when the appliance is deactivated. • When the programme starts, a red light comes on and stays on for all the duration of the programme.
ENGLISH 5.
www.aeg.com Programme Degree of soil Type of load Programme phases Options P8 • Normal soil • Crockery and cutlery • • • • • Multitab 6) Prewash Wash 50 °C Rinses Dry 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
ENGLISH 5.2 Information for test institutes 29 info.test@dishwasher-production.com For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.1 Programme selection mode and user mode When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. How to set the water softener level The appliance must be in programme selection mode. 1. To enter the user mode, press and hold simultaneously until the indicators and , . • The indicators go off. , and continues to • The indicator flash.
ENGLISH The use of the option Multitab with the rinse aid dispenser deactivated may not give satisfying drying results. When the rinse aid dispenser is deactivated, the rinse aid indicator is always off when the option Multitab is activated. How to deactivate the rinse aid dispenser The appliance must be in programme selection mode. 1. To enter the user mode, press and until the indicators , . • The indicators go off. , and • The indicator continues to flash.
www.aeg.com 7.1 Multitab Activate this option when you use multitablets that integrate the salt, rinse aid and detergent functions. They can also contain other cleaning or rinsing agents. This option deactivates the release of salt. The salt indicator does not come on. This option also deactivates the release of rinse aid but only when the rinse aid dispenser is deactivated, (rinse aid indicator does not come on).
ENGLISH The salt is used to recharge the resin in the water softener and to assure good washing results in the daily use. How to fill the salt container 33 8.2 How to fill the rinse aid dispenser A B 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (Only for the first time). 3. Fill the salt container with dishwasher salt. C 4. Remove the salt around the opening of the salt container. 5.
www.aeg.com 9.1 Using the detergent A B C CAUTION! Only use detergent specifically designed for dishwashers. 1. Press the release button (A) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (B). 3. If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the lid locks into position. 9.
ENGLISH 35 Cancelling the programme End of programme Press and hold RESET until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme. When the programme is completed and you open the door, the appliance is automatically deactivated. Close the water tap. 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment.
www.aeg.com • Do not put in the appliance items that can absorb water (sponges, household cloths). • Remove remaining food from the items. • Make soft the remaining burned food on the items. • Put hollow items (cups, glasses and pans) with the opening down. • Make sure that cutlery and dishes do not bond together. Mix spoons with other cutlery. • Make sure that glasses do not touch other glasses. • Put small items in the cutlery basket. • Put light items in the upper basket.
ENGLISH 37 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.
www.aeg.com • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. 12. TROUBLESHOOTING If the appliance does not start or it stops during operation. Before you contact an Authorised Service Centre, check if you can solve the problem by yourself with the help of the information in the table. With some problems, the display shows an alarm code.
ENGLISH 39 12.1 The washing and drying results are not satisfactory Problem Possible solution There are whitish streaks or bluish layers on glasses and dishes. • The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position. • The quantity of detergent is too much. There are stains and dry water drops on glasses and dishes. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid selector to a higher position.
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 41 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 42 3. DESCRIPTION DE L'APPAREIL.............................................................................. 44 4. BANDEAU DE COMMANDE................................................................................. 45 5. PROGRAMMES..........................
FRANÇAIS 1. 41 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • L'appareil doit être raccordé au réseau de distribution d'eau en utilisant les ensembles de raccordement neufs fournis avec l'appareil, il convient de ne pas réutiliser des ensembles de raccordement usagés. 1.
FRANÇAIS débrancher l'appareil. Tirez toujours sur la fiche. • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 45 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ProBoost 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche Multitab Touche RESET Voyants 4.1 Voyants Voyant Description Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.
FRANÇAIS Eau (l) Consommation électrique (kWh) Durée (min) P2 7 - 14 0.6 - 1.4 40 - 150 P3 14 - 16 1.2 - 1.5 139 - 149 P4 12.5 - 14.5 1.4 - 1.6 154 - 164 P5 12 - 14 0.7 - 0.9 75 - 85 P6 9.5 - 10.5 1.10 - 1.30 55 - 65 P7 10 0.9 30 P8 9 - 10 1.0 - 1.
www.aeg.com Comment régler le mode Programmation impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'appareil est en mode Programmation lorsque le numéro de programmeP1 s'affiche. Lorsque vous allumez l'appareil, il est généralement en mode Programmation.
FRANÇAIS • L'affichage indique le réglage actuel : Par ex., = niveau 5. 3. Appuyez sur la touche à plusieurs reprises pour modifier le réglage. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.3 Le distributeur de liquide de rinçage Le liquide de rinçage permet de sécher la vaisselle sans laisser de traînées ni de taches. Le liquide de rinçage est automatiquement ajouté au cours du rinçage chaud.
www.aeg.com liquide de rinçage est activé (réglage usine). 3. Appuyez sur la touche modifier le réglage. pour = le distributeur de liquide de rinçage est désactivé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.5 Signaux sonores Les signaux sonores se déclenchent en cas d''anomalie de fonctionnement de l'appareil. Il est impossible de désactiver ces signaux sonores. Un signal sonore retentit également lorsque le programme est terminé.
FRANÇAIS améliorer les résultats de lavage et de séchage offerts par les pastilles tout-enun. Multitab n'est pas une option permanente et doit être sélectionnée à chaque cycle. Comment activer l'option Multitab Appuyez sur la touche . Le voyant correspondant s'allume. 7.2 TimeSaver Cette option augmente la pression et la température de l'eau. Les phases de lavage et de séchage sont réduites. La durée totale du programme diminue d'environ 50 %.
www.aeg.com Remplissage du réservoir de sel régénérant 1. Tournez le couvercle du réservoir de sel régénérant vers la gauche et retirez-le. 2. Versez 1 litre d'eau dans le réservoir de sel régénérant (uniquement la première fois). 3. Remplissez le réservoir avec du sel régénérant. 8.2 Comment remplir le distributeur de liquide de rinçage A B C 4. Enlevez le sel qui se trouve autour de l'ouverture du réservoir de sel régénérant. 5.
FRANÇAIS 53 • Si le voyant du liquide de rinçage est allumé, remplissez le distributeur de liquide de rinçage. 3. Chargez les paniers. 4. Ajoutez le produit de lavage. Si vous utilisez des pastilles de détergent tout en 1, activez l'option Multitab. 5. Réglez et lancez le programme adapté au type de vaisselle et au degré de salissure. automatiquement l'appareil lorsqu'il ne fonctionne pas. 9.1 Utilisation du produit de lavage 1. Laissez la porte de l'appareil entrouverte. 2.
www.aeg.com Ouverture de la porte au cours du fonctionnement de l'appareil Si vous ouvrez la porte lorsqu'un programme est en cours, l'appareil s'arrête. Lorsque vous refermez la porte, l'appareil reprend là où il a été interrompu. Durant la phase de séchage, si la porte est ouverte pendant plus de 30 secondes, le programme en cours s'arrête. Annulation du programme Appuyez sur RESET jusqu'à ce que l'appareil soit en mode de sélection du programme.
FRANÇAIS 21 °dH. Dans les régions où la dureté dépasse cette limite, du liquide de rinçage et du sel régénérant doivent être utilisés en complément des pastilles tout en 1. Cependant, dans les régions où l'eau est dure ou très dure, nous recommandons l'utilisation séparée d'un détergent simple (poudre, gel, pastille, sans fonction supplémentaire), de liquide de rinçage et de sel régénérant pour des résultats de lavage et de séchage optimaux.
www.aeg.com 10.6 Déchargement des paniers 1. Attendez que la vaisselle refroidisse avant de la retirer du lave-vaisselle. La vaisselle encore chaude est sensible aux chocs. 2. Déchargez d'abord le panier inférieur, puis le panier supérieur. À la fin du programme, les côtés et la porte de l'appareil peuvent être mouillés. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
FRANÇAIS 57 ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d’aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A).
www.aeg.com 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête en cours de programme. Avant de contacter le service après-vente, vérifiez d'abord si vous ne pouvez pas résoudre le problème vous même à l'aide des informations du tableau. Pour certaines anomalies, l'écran affiche un code d'alarme. Problème et code d'alarme Solution possible L'appareil ne s'allume pas. • Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant.
FRANÇAIS 59 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Solution possible Traînées blanchâtres ou pellicules bleuâtres sur les verres et la vaisselle. • La quantité de liquide de rinçage libérée est trop importante. Placez le sélecteur de dosage du liquide de rinçage sur un niveau plus faible. • La quantité de produit de lavage est excessive. Taches et traces de gouttes • La quantité de liquide de rinçage libérée n'est pas sufd'eau séchées sur les verres et fisante.
www.aeg.com Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour les autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple, panneaux solaires ou énergie éolienne), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 14. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le électroniques. Ne jetez pas les appareils symbole .
FRANÇAIS 61
www.aeg.
FRANÇAIS 63
117900691-A-312014 www.aeg.