NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 25 46 FAVORIT 65712 VI0P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant. 2.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Top sproeiarm Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 Beam-on-Floor De Beam-on-Floor is een lichtstraal die op de keukenvloer onder de deur van het apparaat verschijnt. • Wanneer het programma start, gaat de rode lichtstraal aan. De lichtstraal blijft gedurende het volledige programma zichtbaar. • Wanneer het programma is voltooid, gaat het groene lampje branden.
NEDERLANDS 4. BEDIENINGSPANEEL 1 1 2 3 4 5 2 3 Aan/uit-toets Weergave Delay-toets Program-toets ExtraHygiene-toets 4 6 7 8 9 5 6 7 8 9 TimeSaver-toets XtraDry-toets Reset-toets Indicatielampjes 4.1 Indicatielampjes Aanduiding Beschrijving Einde-indicatielampje. XtraDry-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. TimeSaver-indicatielampje.
www.aeg.
NEDERLANDS Water (l) Energie (kWh) Bereidingsduur (min) P3 12.5 - 14.5 1.4 - 1.6 154 - 164 P4 12 - 14 0.7 - 0.9 75 - 85 P5 10 0.9 30 P6 9 - 10 1.0 - 1.2 219 - 229 Programma 1) 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
www.aeg.com De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten. Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.
NEDERLANDS U kunt de vrij te geven hoeveelheid glansmiddel instellen tussen stand 1 (laagste hoeveelheid) en stand 6 (hoogste hoeveelheid). Niveau 0 schakelt het glansmiddeldoseerbakje uit en er wordt geen glansmiddel afgegeven. Fabrieksinstelling: stand 4. Het instellen van het glansmiddelniveau 2. Druk op en , . , en , , , en gaan knipperen en het display blanco is. , , en gaan knipperen en het display blanco is. en Het apparaat moet in de programmakeuzemodus staan.
www.aeg.com , , en gaan knipperen en het display blanco is. 2. Druk op voeren tegelijkertijd en ingedrukt tot de indicatielampjes • De indicatielampjes en 1. Houd om de gebruikersmodus in te , , gaan uit. • Het indicatielampje blijft knipperen. • Het display toont de huidige instelling: uit. 3. Druk op wijzigen. = Geluidssignaal om de instelling te = Geluidssignaal aan. 4. Druk op de knop aan/uit om de instelling te bevestigen. 6.
NEDERLANDS TimeSaver activeren Druk op . Het bijbehorende indicatielampje gaat nu branden. Als de optie niet van toepassing is op het programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit. Het display geeft de bijgewerkte programmaduur weer. 7.3 ExtraHygiene 13 • Tijdens de droogfase wordt de deur van het apparaat automatisch geopend en op een kier gehouden. • Aan het einde van het programma wordt de deur vanzelf weer dicht getrokken.
www.aeg.com 3. Vul het glansmiddeldoseerbakje. 4. Draai de waterkraan open. 5. Start een programma om resten te verwijderen die misschien nog in het apparaat zijn achtergebleven. Gebruik geen afwasmiddel en gebruik de mandjes niet. Als u een programma start, doet het apparaat er ongeveer 5 minuten over om de hars in de waterontharder te herladen. Het lijkt alsof het apparaat niet werkt. De wasfase start pas nadat deze procedure voltooid is. De procedure wordt periodiek herhaald. 8.
NEDERLANDS Vul het glansmiddeldoseerbakje bij wanneer de indicatie (A) helder wordt. 15 Als u multitabletten gebruikt en het droogresultaat is naar tevredenheid, kan de indicatie voor het glansmiddel worden uitgeschakeld. We raden u aan altijd glansmiddel te gebruiken voor een betere droogprestatie, zelfs in combinatie met wastabletten die glansmiddel bevatten. 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren.
www.aeg.com programma worden op het display 3 seconden weergegeven. 4. Stel de bruikbare opties in. 5. Sluit de deur van de afwasmachine om het programma te starten. Een programma starten met een uitgestelde start 1. Stel een programma in. De uitgestelde start annuleren tijdens het aftellen Als u de uitgestelde start annuleert, moet u het programma en de opties opnieuw instellen. Houd tegelijkertijd Reset ingedrukt tot het apparaat in de programmakeuzemodus staat. 2.
NEDERLANDS 17 multitabletten (bijv. ''3in1'', ''4in1'', ''All in 1''). Volg de aanwijzing op de verpakking. • U dient het juiste programma in te stellen voor het type lading en de mate van vervuiling. Het programma ECO biedt het meest efficiënte wateren energieverbruik voor normaal vervuild serviesgoed en bestek. 3. Start het kortste programma met een spoelfase. Voeg geen vaatwasmiddel toe en ruim de mandjes niet in. 4.
www.aeg.com • De positie van de items in de mandjes correct is. • Het programma van toepassing is op het type lading en de mate van bevuiling. • De juiste hoeveelheid afwasmiddel is gebruikt. borden zijn gevoelig voor beschadigingen. 2. Ruim eerst het onderrek en dan het bovenrek uit Aan het einde van het programma kan er water aan de zijkanten en de deur van het apparaat achterblijven. 10.6 De rekken uitruimen 1. Laat de borden afkoelen voordat u deze uit het apparaat neemt Hete 11.
NEDERLANDS 19 11.2 De bovenste sproeiarm schoonmaken We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt. Verstopte gaten kunnen onbevredigende wasresultaten opleveren. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A).
www.aeg.com 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. de deur, met een zachte, vochtige doek. • Als u regelmatig korte programma's gebruikt dan kunnen er vetresten en kalkaanslag achterblijven in het apparaat. Om dit te voorkomen raden we aan minstens 2 keer per maand progamma's met een lange duur te gebruiken.
NEDERLANDS 21 Probleem en alarmcode Mogelijke oorzaak en oplossing Het programma begint niet. • Zorg dat de deur van het apparaat is gesloten. • Als de starttijdkeuze start is ingesteld, annuleert u deze functie of wacht u tot het einde van het aftellen. • Het apparaat is begonnen met de oplaadprocedure van de hars in de waterontharder. De duur van de procedure is ongeveer 5 minuten. Het apparaat neemt geen water. Op het display verschijnt • Controleer of de waterkraan is geopend.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing Ratelende / kloppende geluiden vanuit het apparaat. • Het serviesgoed is niet juist in de korven gerangschikt. Raadpleeg de folder voor het laden van de korven. • Zorg ervoor dat de sproeiarmen vrij kunnen ronddraaien. Het apparaat maakt kortsluiting. • De stroomsterkte is onvoldoende om alle tegelijk werkende apparaten van stroom te voorzien.
NEDERLANDS 23 Probleem Mogelijke oorzaak en oplossing Het serviesgoed is nat. • Activeer voor de beste droogprestatie de optie XtraDry. • Het programma heeft geen droogfase of heeft een droogfase met lage temperatuur. • Het glansmiddeldoseerbakje is leeg. • De kwaliteit van het glansmiddel kan de oorzaak zijn. • De kwaliteit van de multitabletten kan de oorzaak zijn. Probeer een ander merk of activeer het glansmiddeldoseerbakje en gebruik het glansmiddel samen met de multitabletten.
www.aeg.com 13. TECHNISCHE INFORMATIE Afmetingen Breedte / hoogte / diepte (mm) 596 / 818-898 / 550 Elektrische aansluiting 1) Voltage (V) 200 - 240 Frequentie (Hz) 50 / 60 bar (minimaal en maximaal) 0.5 - 8 MPa (minimaal en maximaal) 0.05 - 0.8 Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 15 Energieverbruik Modus aan laten (W) 0.99 Energieverbruik Uit-modus (W) 0.10 Watertoevoerdruk 1) Zie het typeplaatje voor andere waarden.
ENGLISH 25 CONTENTS 1. SAFETY INFORMATION.........................................................................................26 2. SAFETY INSTRUCTIONS........................................................................................ 27 3. PRODUCT DESCRIPTION...................................................................................... 28 4. CONTROL PANEL...................................................................................................29 5. PROGRAMMES....................
1. www.aeg.com SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
ENGLISH • • • • • • 27 Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
www.aeg.com WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
ENGLISH 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Lower basket 11 Upper basket 12 Cutlery drawer 3.1 Beam-on-Floor • When the appliance has a malfunction, the red light flashes. The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door. The Beam-on-Floor goes off when the appliance is deactivated. • When the programme starts, a red light comes on and stays on for all the duration of the programme.
www.aeg.com Indicator Description Delay indicator. ExtraHygiene indicator. 5.
ENGLISH 31 5.1 Consumption values Water (l) Energy (kWh) Duration (min) P1 11 0.857 225 P2 7 - 14 0.6 - 1.4 40 - 150 P3 12.5 - 14.5 1.4 - 1.6 154 - 164 P4 12 - 14 0.7 - 0.9 75 - 85 P5 10 0.9 30 P6 9 - 10 1.0 - 1.2 219 - 229 Programme 1) 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
www.aeg.com 6.2 The water softener The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance. The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area.
ENGLISH The rinse aid is automatically released during the hot rinse phase. You can set the released quantity of rinse aid between level 1 (minimum quantity) and level 6 (maximum quantity). Level 0 will deactivate the rinse aid dispenser and no rinse aid will be released. Factory setting: level 4. The appliance must be in programme selection mode. 1. To enter the user mode, press and and hold simultaneously the indicators , , , until and start to flash and the display is blank. 2. Press .
www.aeg.com • The indicators , , and go off. • The indicator continues to flash. • The display shows the current setting: 3. Press = Acoustic signal off. to change the setting. = Acoustic signal on. 4. Press the on/off button to confirm the setting. 6.6 How to deactivate AutoOpen The appliance must be in programme selection mode. the indicators , , , and start to flash and the display is blank. 2. Press . • The indicators , , and go off. continues to • The indicator flash.
ENGLISH not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated programme duration. 7.3 ExtraHygiene With this option you have better hygiene results. During the last rinsing phase, the temperature stays at 70 °C for at least 10 minutes. How to activate ExtraHygiene Press , the related indicator comes on If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off.
www.aeg.com 8.1 The salt container CAUTION! Only use salt specifically designed for dishwashers. 8.2 How to fill the rinse aid dispenser A B The salt is used to recharge the resin in the water softener and to assure good washing results in the daily use. How to fill the salt container 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (Only for the first time). 3. Fill the salt container with dishwasher salt.
ENGLISH • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent A B 37 Starting a programme 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3.
www.aeg.com Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Make sure that there is detergent in the detergent dispenser before you start a new programme. End of programme Press and hold Reset until the appliance is in programme selection mode. When the programme is completed and you open the door, the appliance is automatically deactivated. Cancelling the programme Close the water tap.
ENGLISH 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5.
www.aeg.com C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 4. Wash the filters.
ENGLISH 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. 41 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. Clogged holes can cause unsatisfactory washing results. 1. Pull out the upper basket. 2.
www.aeg.com With some problems, the display shows an alarm code. to contact an Authorised Service Centre. The majority of problems that can occur can be solved without the need Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The program does not start. • Make sure that the appliance door is closed.
ENGLISH 43 Problem and alarm code Possible cause and solution Small leak from the appliance door. • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • Parts of the tableware are protruding from the baskets.
www.aeg.com Problem Possible cause and solution There are stains and dry water drops on glasses and dishes. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • The quality of the rinse aid can be the cause. The dishes are wet. • For the best drying performance activate the option XtraDry. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty.
ENGLISH 45 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818-898 / 550 Electrical connection 1) Voltage (V) 200 - 240 Frequency (Hz) 50 / 60 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 15 Power consumption Left-on mode (W) 0.99 Power consumption Off-mode (W) 0.10 Water supply pressure 1) Refer to the rating plate for other values.
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 47 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 48 3. DESCRIPTION DE L'APPAREIL.............................................................................. 50 4. BANDEAU DE COMMANDE................................................................................. 51 5. PROGRAMMES..........................
FRANÇAIS 1. 47 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 51 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche XtraDry Touche Reset Voyants 4.1 Voyants Indicateur Désignation Voyant de fin. Voyant XtraDry. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme.
www.aeg.
FRANÇAIS Eau (l) Consommation électrique (kWh) Durée (min) P2 7 - 14 0.6 - 1.4 40 - 150 P3 12.5 - 14.5 1.4 - 1.6 154 - 164 P4 12 - 14 0.7 - 0.9 75 - 85 P5 10 0.9 30 P6 9 - 10 1.0 - 1.2 219 - 229 Programme 1) 53 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com 6.2 Adoucisseur d'eau L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région.
FRANÇAIS • L'affichage indique le réglage actuel : Par ex., = niveau 5. 3. Appuyez sur la touche à plusieurs reprises pour modifier le réglage. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.3 Le distributeur de liquide de rinçage Le liquide de rinçage permet de sécher la vaisselle sans laisser de traînées ni de taches. Le liquide de rinçage est automatiquement ajouté au cours du rinçage chaud.
www.aeg.com = le distributeur de liquide de rinçage est désactivé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.5 Signaux sonores Les signaux sonores se déclenchent en cas d''anomalie de fonctionnement de l'appareil. Il est impossible de désactiver ces signaux sonores. Un signal sonore retentit également lorsque le programme est terminé. Par défaut, ce signal sonore est désactivé, mais il est possible de l'activer.
FRANÇAIS 7.1 XtraDry Activez cette option lorsque vous voulez améliorer les performances de séchage. En utilisant cette option, la durée de certains programmes, la consommation d'eau et la température du dernier rinçage peuvent être affectés. L'option XtraDry n'est pas une option permanente et doit être sélectionnée à chaque cycle. Comment activer l'option XtraDry Appuyez sur . Le voyant correspondant s'allume.
www.aeg.com Si vous souhaitez désactiver l'option AutoOpen, reportez-vous au chapitre « Réglages ». Dans ces conditions, la consommation d'énergie du programme augmente et les performances de séchage sont considérablement réduites. Pour améliorer les performances de séchage, reportez-vous à l'option XtraDry. 8. AVANT LA PREMIÈRE UTILISATION 1. Assurez-vous que le réglage actuel de l'adoucisseur d'eau est compatible avec la dureté de l'arrivée d'eau.
FRANÇAIS 8.2 Comment remplir le distributeur de liquide de rinçage A B 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. Remplissez le distributeur de liquide de rinçage lorsque le voyant (A) s'allume.
www.aeg.com ATTENTION! Utilisez uniquement un produit de lavage spécial pour lave-vaisselle. 1. Appuyez sur la touche de déverrouillage (A) pour ouvrir le couvercle (C). 2. Versez le produit de lavage sous forme de poudre ou tablette dans le compartiment approprié (B). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. 9.
FRANÇAIS Annulation du programme Fin de programme Appuyez sur Reset jusqu'à ce que l'appareil soit en mode de sélection du programme. Assurez-vous que le distributeur de produit de lavage n'est pas vide avant de démarrer un nouveau programme de lavage. Lorsque le programme est terminé et que vous ouvrez la porte, l'appareil s'éteint automatiquement. 61 Fermez le robinet d'eau. 10. CONSEILS 10.
www.aeg.com 10.3 Que faire si vous ne voulez plus utiliser de pastilles de détergent multifonctions Avant de commencer à utiliser du produit de lavage, du sel régénérant et du liquide de rinçage séparément, effectuez la procédure suivante. 1. Réglez l'adoucisseur d'eau au niveau maximal. 2. Assurez-vous que le réservoir de sel régénérant et le distributeur de liquide de rinçage sont pleins. 3. Lancez le programme le plus court avec une phase de rinçage.
FRANÇAIS 63 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur. Les filtres sales et les bras d'aspersion obstrués diminuent les résultats de lavage. Contrôlez-les régulièrement et nettoyezles si nécessaire. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 11.1 Nettoyage des filtres Le système de filtrage se compose de trois éléments. 4. Lavez les filtres. C B A 1.
www.aeg.com 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices. 4.
FRANÇAIS • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur • Nettoyez soigneusement l'appareil, y compris le joint en caoutchouc de la porte, avec un chiffon doux humide. • Si vous utilisez régulièrement des programmes de courte durée, des dépôts de graisse et des dépôts calcaires peuvent se former à 65 l'intérieur de l'appareil. Pour éviter cela, nous recommandons de lancer un programme long au moins 2 fois par mois.
www.aeg.com Problème et code d'alarme Cause et solution possibles L'appareil n'est pas approvi- • Assurez-vous que le robinet d'eau est ouvert. sionné en eau. • Assurez-vous que la pression de l'arrivée d'eau n'est pas trop basse. Pour obtenir cette information, contactez . L'affichage indique votre compagnie des eaux. • Assurez-vous que le robinet d'eau n'est pas obstrué. • Assurez-vous que le filtre du tuyau d'arrivée d'eau n'est pas obstrué.
FRANÇAIS 67 Problème et code d'alarme Cause et solution possibles L'appareil déclenche le disjoncteur. • L'ampérage n'est pas suffisant pour alimenter tous les appareils en cours de fonctionnement simultanément. Vérifiez l'ampérage de la prise et la capacité du mètre, ou éteignez l'un des appareils qui sont en cours de fonctionnement. • Défaut électrique interne de l'appareil. Faites appel à un service après vente agréé.
www.aeg.com Problème Cause et solution possibles La vaisselle est mouillée. • Pour de meilleurs performances de séchage, activez l'option XtraDry. • Le programme ne contient pas de phase de séchage ou une phase de séchage à basse température. • Le distributeur de liquide de rinçage est vide. • Il se peut que la qualité du liquide de rinçage soit en cause. • Il se peut que la qualité des pastilles tout-en-1 soit en cause.
FRANÇAIS 69 Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818-898 / 550 Branchement électrique1) Tension (V) 200 - 240 Fréquence (Hz) 50 / 60 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude2) max.
www.aeg.
FRANÇAIS 71
117900863-A-162015 www.aeg.