NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 22 40 FAVORIT 65712 VI0P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • Het apparaat moet met de nieuwe slangset worden aangesloten op een kraan. Oude slangsets mogen niet opnieuw worden gebruikt. 1.
NEDERLANDS • Alleen voor VK en Ierland. Het apparaat heeft een stekker van 13 ampère. Als de zekering van de stekker verwisseld moet worden, gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Top sproeiarm Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 Beam-on-Floor De Beam-on-Floor is een lichtstraal die op de keukenvloer onder de deur van het apparaat verschijnt. • Wanneer het programma start, gaat de rode lichtstraal aan. De lichtstraal blijft gedurende het volledige programma zichtbaar. • Wanneer het programma is voltooid, gaat het groene lampje branden.
NEDERLANDS 4. BEDIENINGSPANEEL 1 1 2 3 4 5 2 Aan/uit-toets Weergave Delay-toets Program-toets ExtraHygiene-toets 3 4 6 7 8 9 5 6 7 8 9 TimeSaver-toets Multitab-toets AutoOpen-toets Indicatielampjes 4.1 Indicatielampjes Aanduiding Omschrijving Einde-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. 5.
www.aeg.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) P6 9 - 10 1.0 - 1.2 219 - 229 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.com Schrijf het productnummer (PNC) op dat u op het typeplaatje vindt. 6. INSTELLINGEN 6.
www.aeg.com Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
NEDERLANDS • Het display toont de huidige instelling: bijv. = niveau 4. – De glansmiddelniveaus lopen van 0A tot 6A. – Niveau 0 = er wordt geen glansmiddel gebruikt. 3. Druk herhaaldelijk op om de instelling te wijzigen. 4. Druk op de knop aan/uit om de instelling te bevestigen. • Blijft het indicatielampje knipperen. • Het display toont de huidige instelling: = het doseerbakje voor glansmiddel is geactiveerd (fabrieksinstelling). 3. Druk op wijzigen.
www.aeg.com 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd. De opties kunnen niet worden in- of uitgeschakeld als een programma in werking is. Niet alle opties kunnen met elkaar worden gecombineerd. Als u opties hebt geselecteerd die niet met elkaar te combineren zijn, dan schakelt het apparaat automatisch één of meerdere opties uit. Alleen de indicatielampjes van de actieve opties blijven aan. 7.
NEDERLANDS 13 Deze optie wordt automatisch geactiveerd als u het programma instelt Het indicatielampje branden. gaat Het is niet mogelijk om deze optie in te stellen bij andere programma's. Als u de optie AutoOpen wilt uitschakelen, drukt u op . Het betrokken indicatielampje gaat uit. Onder deze omstandigheden neemt het energieverbruik van het programma toe. • Als de droogfase in werking is, wordt de deur van het apparaat op een kier gezet. • Aan het einde van het programma wordt de deur dichtgetrokken.
www.aeg.com 8.2 Het vullen van het glansmiddeldoseerbakje A B 4. Verwijder het zout rond de opening van het zoutreservoir. C 5. Draai de dop van het zoutreservoir rechtsom om het zoutreservoir te sluiten. Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Gevaar voor roest. Start om dit te voorkomen een programma nadat u het zoutreservoir heeft bijgevuld. LET OP! Gebruik alleen glansspoelmiddel voor afwasautomaten. 1. Open het deksel (C). 2.
NEDERLANDS 9.1 Vaatwasmiddel gebruiken A B C LET OP! Gebruik uitsluitend vaatwasmiddelen die specifiek zijn bedoeld voor gebruik in vaatwassers 1. Druk op de ontgrendelknop (A) om de deksel te openen (C). 2. Doe de vaatwastablet of het poeder in het doseerbakje (B). 3. Plaats een kleine hoeveelheid van het vaatwasmiddel in de binnenkant van de deur van het apparaat als het programma een voorwasfase heeft. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. 9.
www.aeg.com De uitgestelde start annuleren tijdens het aftellen Als u de uitgestelde start annuleert, moet u het programma en de opties opnieuw instellen. Houd tegelijkertijd en ingedrukt tot het apparaat in de programmakeuzemodus staat. Controleer of er afwasmiddel in het afwasmiddeldoseerbakje aanwezig is voordat u een nieuw programma start. Einde van het programma Wanneer het programma is voltooid en u opent de deur, wordt het apparaat automatisch uitgeschakeld. Draai de waterkraan dicht.
NEDERLANDS 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4. Als het programma is voltooid, wijzigt u de waterontharder in de waterhardheid van uw omgeving. 5.
www.aeg.com 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
NEDERLANDS 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 19 11.
www.aeg.com Probleem en alarmcode Mogelijke oplossing De anti-overstromingsbevei- • Draai de waterkraan dicht en neem contact op met de liging is aan. klantenservice. Op het display verschijnt . Schakel het apparaat na controle aan en uit. Als het probleem opnieuw optreedt, neemt u contact op met onze klantenservice. Voor alarmcodes die niet in de tabel vermeld zijn, neemt u contact op met de klantenservice. 12.
NEDERLANDS Vermogen Couverts 15 Energieverbruik Modus aan laten (W) 0.99 Energieverbruik Uit-modus (W) 0.10 21 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door een alternatieve, milieuvriendelijkere energiebron geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14. MILIEUBESCHERMING Recycle de materialen met het symbool . Gooi de verpakking in een geschikte verzamelcontainer om het te recyclen.
www.aeg.com CONTENTS 1. SAFETY INFORMATION.........................................................................................23 2. SAFETY INSTRUCTIONS........................................................................................ 24 3. PRODUCT DESCRIPTION...................................................................................... 25 4. CONTROL PANEL...................................................................................................26 5. PROGRAMMES................
ENGLISH 1. 23 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com 1.2 Children and vulnerable people safety • • • • • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Do not let children play with the appliance. Keep all detergents away from children.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
www.aeg.com 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Lower basket 11 Upper basket 12 Cutlery drawer 3.1 Beam-on-Floor • When the appliance has a malfunction, the red light flashes. The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door. The Beam-on-Floor goes off when the appliance is deactivated. • When the programme starts, a red light comes on and stays on for all the duration of the programme.
ENGLISH 27 5.
www.aeg.com Programme 1) Water (l) Energy (kWh) Duration (min) P2 7 - 14 0.6 - 1.4 40 - 150 P3 12.5 - 14.5 1.4 - 1.6 154 - 164 P4 12 - 14 0.7 - 0.9 75 - 85 P5 10 0.9 30 P6 9 - 10 1.0 - 1.2 219 - 229 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes For all the necessary information for test performance, send an email to: info.
ENGLISH The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in 29 your area. Your local water authority can advise you on the hardness of the water in your area. It is important to set the right level of the water softener to assure good washing results.
www.aeg.com the indicators , , and start to flash and the display is blank. 2. Press . • The indicators off. , and go continues to • The indicator flash. • The display shows the current setting: e.g. = level 4. – The levels of rinse aid are from 0A to 6A. – Level 0 = no rinse aid is released. • The indicators off. , and go • The indicator continues to flash. • The display shows the current = the rinse aid setting: dispenser is activated (factory setting). 3. Press to change the setting.
ENGLISH 31 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on. The total programme duration decreases by approximately 50%.
www.aeg.com • While the drying phase operates, a device opens the appliance door and keeps it ajar. • At the end of the programme, the device and the appliance door retract. The appliance is automatically deactivated. CAUTION! Do not try to close the appliance door while the device keeps the door ajar. This can cause damage to the appliance. This option is automatically activated when you select the programme The indicator . comes on. It is not possible to select this option with other programmes.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 33 CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. C 9. DAILY USE 1. Open the water tap. 2.
www.aeg.com Starting a programme 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press repeatedly until the display shows the number of the programme you want to start. The display will show the programme number for approximately 3 seconds and then show the programme duration. The display will show the programme number for approximately 3 seconds and then show the programme duration. 4.
ENGLISH • You can use dishwasher detergent, rinse aid and salt separately or you can use the multi-tablets (e.g. ''3in1'', ''4in1'', ''All in 1''). Follow the instructions written on the packaging. • Select the programme according to the type of load and degree of soil. With the ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher.
www.aeg.com • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct. • The programme is applicable for the type of load and for the degree of soil. • The correct quantity of detergent is used. 10.6 Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket.
ENGLISH 37 CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 11.
www.aeg.com With some problems, the display shows an alarm code. Problem and alarm code Possible solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The programme does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown.
ENGLISH 39 Problem Possible solution The dishes are wet. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together. Refer to "Hints and tips" for other possible causes. 13.
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 41 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 42 3. DESCRIPTION DE L'APPAREIL.............................................................................. 44 4. BANDEAU DE COMMANDE................................................................................. 45 5. PROGRAMMES..........................
FRANÇAIS 1. 41 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • L'appareil doit être raccordé au réseau de distribution d'eau en utilisant les ensembles de raccordement neufs fournis avec l'appareil, il convient de ne pas réutiliser des ensembles de raccordement usagés. 1.
FRANÇAIS • Ne tirez jamais sur le câble d'alimentation électrique pour débrancher l'appareil. Tirez toujours sur la fiche. • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 45 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 9 8 Touche TimeSaver Touche Multitab Touche AutoOpen Voyants 4.1 Voyants Voyant Description Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.
FRANÇAIS Programme 1) P6 Eau (l) Consommation électrique (kWh) Durée (min) 9 - 10 1.0 - 1.2 219 - 229 47 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.2 Informations pour les instituts de test Pour toute information relative aux performances de test, envoyez un courrier électronique à l'adresse : info.
www.aeg.com Dureté de l'eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.
FRANÇAIS mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur la touche • Les voyants s'éteignent. , . et continue à • Le voyant clignoter. • L'affichage indique le réglage actuel : Par ex., = niveau 4. – Les niveaux de liquide de rinçage s'échelonnent de 0A à 6A. – Niveau 0 = aucun liquide de rinçage n'est libéré. 3. Appuyez sur la touche à plusieurs reprises pour modifier le réglage. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
www.aeg.com mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. , = Signal sonore activé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. et continue à clignoter. • Le voyant • L'affichage indique le réglage actuel : désactivé. 3. Appuyez sur réglage. = Signal sonore pour modifier le 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme.
FRANÇAIS pendant quelques secondes, puis s'éteint. L'affichage indique la durée du programme réactualisée. 7.3 ExtraHygiene Cette option assure des résultats plus hygiéniques. Au cours de la dernière phase de rinçage, la température reste à 70 °C pendant au moins 10 minutes. • Durant la phase de séchage, un dispositif entrouvre la porte de l'appareil. • À la fin du programme, le dispositif se rétracte et la porte de l'appareil se referme. L'appareil s'éteint automatiquement.
www.aeg.com N'utilisez pas de produit de lavage et ne chargez pas les paniers. Lorsque vous démarrez un programme, l'appareil peut prendre 5 minutes pour recharger la résine dans l'adoucisseur d'eau. Pendant ce temps, l'appareil semble ne pas fonctionner. La phase de lavage ne démarre qu'une fois cette procédure achevée. La procédure sera répétée régulièrement. 8.1 Réservoir de sel régénérant ATTENTION! Utilisez uniquement du sel régénérant conçu pour les lave-vaisselle.
FRANÇAIS absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. 53 Remplissez le distributeur de liquide de rinçage lorsque le voyant (A) s'allume. 9. UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. • Si le voyant du réservoir de sel régénérant est allumé, remplissez le réservoir.
www.aeg.com que vous souhaitez lancer. Le numéro du programme s'affiche pendant environ 3 secondes, puis la durée du programme s'affiche. Le numéro du programme s'affiche pendant environ 3 secondes, puis la durée du programme s'affiche. 4. Sélectionnez les options compatibles. 5. Fermez la porte de l'appareil pour démarrer le programme. Démarrage d'un programme avec départ différé 1. Sélectionnez un programme. 2.
FRANÇAIS pas ou ne se recouvrent pas les uns les autres. • Vous pouvez utiliser du détergent, du liquide de rinçage et du sel régénérant séparément, ou des pastilles tout en 1 (par ex. « 3 en 1 », « 4 en 1 » ou « tout en 1 »). Suivez les instructions indiquées sur l'emballage. • Sélectionnez le programme en fonction du type de vaisselle et du degré de salissure. Le programme ECO vous permet d'optimiser votre consommation d'eau et d'énergie pour la vaisselle et les couverts normalement sales. 10.
www.aeg.com • Placez les petits articles dans le panier à couverts. • Placez les objets légers dans le panier supérieur. Disposez-les de façon à ce qu'ils ne puissent pas se retourner. • Assurez-vous que le bras d'aspersion tourne librement avant de lancer un programme. 10.5 Avant le démarrage d'un programme Assurez-vous que : • Les filtres sont propres et correctement installés. • Le bouchon du réservoir de sel régénérant est vissé. • Les bras d'aspersion ne sont pas obstrués.
FRANÇAIS 57 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 4. Lavez les filtres. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A). Vérifiez qu'il est correctement positionné sous les deux guides.
www.aeg.com 11.4 Nettoyage intérieur • Nettoyez soigneusement l'appareil, y compris le joint caoutchouc du hublot avec un chiffon doux humide. • Si vous utilisez régulièrement des programmes de courte durée, des dépôts de graisse et des dépôts calcaires peuvent se former à l'intérieur de l'appareil. Pour éviter cela, nous recommandons de lancer un programme long au moins 2 fois par mois. 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête en cours de programme.
FRANÇAIS 59 Si des codes d'alarme non décrits dans le tableau fourni s'affichent, contactez le service après-vente. 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Solution possible Traînées blanchâtres ou pellicules bleuâtres sur les verres et la vaisselle. • La quantité de liquide de rinçage libérée est trop importante. Placez le sélecteur de dosage du liquide de rinçage sur un niveau plus faible. • La quantité de produit de lavage est excessive.
www.aeg.com Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour les autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple, panneaux solaires ou énergie éolienne), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 14. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le électroniques. Ne jetez pas les appareils symbole .
FRANÇAIS 61
www.aeg.
FRANÇAIS 63
117900861-A-302014 www.aeg.