NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 24 44 FAVORIT 65712 M0P FAVORIT 65712 W0P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant. 2.4 Gebruik • Ga niet op de open deur zitten of staan. • Vaatwasmiddel is gevaarlijk.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 4 7 5 6 6 Option-toets 7 Indicatielampjes 8 Start-toets 4.1 Indicatielampjes Aanduiding Omschrijving Wasfase. Gaat aan wanneer de wasfase loopt. Spoelfase. Gaat aan wanneer de spoelfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. Multitab-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is.
www.aeg.com 5.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) 7 - 14 0.6 - 1.4 40 - 150 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 9 - 10 1.0 - 1.2 219 - 229 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
www.aeg.com de waterontharder in te stellen voor goede wasresultaten. Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.
NEDERLANDS en gaan knipperen en het display blanco is. 2. Druk op Delay. • De indicatielampjes en gaan uit. • Blijft het indicatielampje knipperen • Het display toont de huidige instelling: bijv. = niveau 4. – De glansmiddelniveaus lopen van 0A tot 6A. – Niveau 0 = er wordt geen glansmiddel gebruikt. 3. Druk herhaaldelijk op Delay om de instelling te wijzigen. 4. Druk op de knop aan/uit om de instelling te bevestigen. 6.
www.aeg.com 7.1 Multitab 7.3 ExtraHygiene Activeer deze optie als u multitabletten gebruikt met zout, glansmiddel en wasmiddel in één tablet. Ze bevatten ook andere schoonmaakmiddelen of spoelmiddelen. Met deze optie heeft u betere hygiëneresultaten. Tijdens de spoelfase blijft de temperatuur gedurende minimaal 10 minuten op 70 °C. Deze optie schakelt de afgifte van zout uit. Het zoutindicatielampje gaat niet branden.
NEDERLANDS Het is niet mogelijk om deze optie in te stellen bij andere programma's. Als u de optie AutoOpen wilt uitschakelen, drukt u op Option totdat 13 het bijbehorende indicatielampje uit gaat. Onder deze omstandigheden neemt het energieverbruik van het programma toe. 8. VOORDAT U HET APPARAAT VOOR DE EERSTE KEER GEBRUIKT 1. Controleer of het ingestelde niveau van de waterontharder juist is voor de waterhardheid in uw omgeving. U kunt het niveau van de waterontharder instellen. 2.
www.aeg.com 8.2 Het vullen van het glansmiddeldoseerbakje A LET OP! Gebruik alleen glansspoelmiddel voor afwasautomaten. B 1. Open het deksel (C). 2. Vul het glansmiddeldoseerbakje (B) niet verder dan de aanduiding ''MAX''. 3. Verwijder gemorst glansmiddel met een absorberend doekje om te voorkomen dat er te veel schuim ontstaat. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. Vul het glansmiddeldoseerbakje bij wanneer de indicatie (A) helder wordt. C 9.
NEDERLANDS 9.2 Een programma instellen en starten De Auto Off-functie Deze functie verlaagt het energieverbruik door het apparaat automatisch uit te schakelen als het niet werkt. De functie gaat werken: • 5 minuten na voltooiing van het programma. • Als het programma na 5 minuten nog niet is gestart. Een programma starten 15 Als het aftellen klaar is, start het programma en gaat het indicatielampje van de lopende fase branden. Het lampje uitgestelde start gaat uit.
www.aeg.com 10. AANWIJZINGEN EN TIPS 10.1 Algemeen De volgende tips zorgen voor optimale schoonmaak- en droogresultaten en helpen ook het milieu te beschermen. • Verwijder grotere etensresten van de borden en gooi ze in de vuilnisbak. • Spoel de vaat niet eerst af. Gebruik indien nodig een voorwasprogramma (indien beschikbaar) of selecteer een programma met een voorwasfase. • Gebruik altijd de hele ruimte van de mandjes.
NEDERLANDS • Plaats holle voorwerpen (bijv. kopjes, glazen en pannen) met de opening naar beneden. • Zorg ervoor dat serviesgoed en bestek niet in elkaar schuiven. Meng lepels met ander bestek. • Zorg er voor dat glazen andere glazen niet aanraken • Leg kleine voorwerpen in de bestekmand. • Leg lichte voorwerpen in het bovenrek. Zorg ervoor dat de voorwerpen niet verschuiven. • Zorg er voor dat de sproeiarm vrij kan ronddraaien voordat u een programma start. 10.
www.aeg.com 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3. Verwijder de platte filter (A). 4. Was de filters. LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De bovenste sproeiarm schoonmaken We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt.
NEDERLANDS om de vuildeeltjes uit de gaten te verwijderen. 19 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 11.4 De binnenkant van de machine reinigen 4.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren. • Zorg dat de stekker in het stopcontact zit. • Zorg dat er geen zekering in de zekeringenkast is doorgebrand. Het programma start niet. • Zorg dat de deur van het apparaat is gesloten. • Druk op Start. • Als de starttijdkeuze start is ingesteld, annuleert u deze functie of wacht u tot het einde van het aftellen. • Het apparaat is begonnen met de oplaadprocedure van de hars in de waterontharder.
NEDERLANDS 21 Probleem en alarmcode Mogelijke oorzaak en oplossing De deur van het apparaat sluit moeilijk. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • Delen van het serviesgoed steken uit de korven. Ratelende / kloppende geluiden vanuit het apparaat. • Het serviesgoed is niet juist in de korven gerangschikt. Raadpleeg de folder over het laden van de korven. • Zorg ervoor dat de sproeiarmen vrij rond kunnen draaien. Het apparaat maakt kortsluiting.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Vlekken en opgedroogde watervlekken op glazen en servies. • De vrijgegeven hoeveelheid glansmiddel is te laag. Zet de dosering van het glansmiddel op een hogere stand. • De kwaliteit van het glansmiddel kan de oorzaak zijn. Het serviesgoed is nat. • Het programma heeft geen droogfase of heeft een droogfase met lage temperatuur. • Het glansmiddeldoseerbakje is leeg. • De kwaliteit van het glansmiddel kan de oorzaak zijn.
NEDERLANDS 23 Raadpleeg "Voor het eerste gebruik", "Dagelijks gebruik" of "Aanwijzingen en tips" voor mogelijke andere oorzaken. 13. TECHNISCHE INFORMATIE Afmetingen Breedte / hoogte / diepte (mm) 596 / 850 / 610 Elektrische aansluiting 1) Voltage (V) 220 - 240 Frequentie (Hz) 50 / 60 bar (minimaal en maximaal) 0.5 - 8 MPa (minimaal en maximaal) 0.05 - 0.8 Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 15 Energieverbruik Modus aan laten (W) 0.
www.aeg.com CONTENTS 1. SAFETY INFORMATION.........................................................................................25 2. SAFETY INSTRUCTIONS........................................................................................ 26 3. PRODUCT DESCRIPTION...................................................................................... 27 4. CONTROL PANEL...................................................................................................28 5. PROGRAMMES................
ENGLISH 1. 25 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
www.aeg.com 5 6 7 8 9 Filters Rating plate Salt container Air vent Rinse aid dispenser 10 11 12 13 Detergent dispenser Lower basket Upper basket Cutlery drawer 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase.
ENGLISH Indicator Description AutoOpen indicator. TimeSaver indicator. Delay indicator. ExtraHygiene indicator. 5.
www.aeg.com Programme 5) Degree of soil Type of load Programme phases • Normal soil • Prewash • Crockery and cut- • Wash 50 °C lery • Rinses • Dry Options • Multitab 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
ENGLISH 31 • The deactivation of the rinse aid dispenser when you want to use the Multitab option without rinse aid. • The level of rinse aid according to the required dosage. Press and hold simultaneously Delay and Option until the appliance is in programme selection mode. These settings will be saved until you change them again. The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance.
www.aeg.com • The indicator continues to flash. • The display shows the current setting: e.g. = level 5. 3. Press Program again and again to change the setting. 4. Press the on/off button to confirm the setting. 6.3 The rinse aid dispenser The rinse aid helps to dry the dishes without streaks and stains. The rinse aid is automatically released during the hot rinse phase. You can set the released quantity of rinse aid between level 1 (minimum quantity) and level 6 (maximum quantity).
ENGLISH 33 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on. The total programme duration decreases by approximately 50%.
www.aeg.com • While the drying phase operates, a device opens the appliance door and keeps it ajar. • At the end of the programme, the device and the appliance door retract. The appliance is automatically deactivated. CAUTION! Do not try to close the appliance door while the device keeps the door ajar. This can cause damage to the appliance. This option is automatically activated when you select the programme The indicator . comes on. It is not possible to select this option with other programmes.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 35 CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. C 9. DAILY USE 1. Open the water tap. 2.
www.aeg.com Starting a programme 1. Close the appliance door. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press Program again and again until the indicator of the programme you want to select comes on. The display shows the programme duration. 4. Set the applicable options. 5. Press Start to start the programme. • The indicator of the running phase comes on. • The programme duration starts to decrease with steps of 1 minute.
ENGLISH the water released from the spray arm nozzles. Make sure that items do not touch or cover each other. • You can use dishwasher detergent, rinse aid and salt separately or you can use the multi-tablets (e.g. ''3in1'', ''4in1'', ''All in 1''). Follow the instructions written on the packaging. • Select the programme according to the type of load and degree of soil. With the ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. 10.
www.aeg.com • The correct quantity of detergent is used. 10.6 Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket. At the end of the programme water can still remain on the sides and on the door of the appliance. 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket.
ENGLISH 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the upper spray arm 39 3. Wash the spray arm under running water. Use a thin pointed tool, e.g. toothpick, to remove particles of soil from the holes. 4.
www.aeg.com 11.4 Internal cleaning • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. • To maintain the performance of your appliance at its best, we recommend to use monthly a specific cleaning product for dishwashers.
ENGLISH Problem and alarm code Possible cause and solution The appliance does not drain the water. • Make sure that the sink spigot is not clogged. • Make sure that the filter in the outlet hose is not clogged. • Make sure that the interior filter system is not clogged. • Make sure that the drain hose has no kinks or bends. The display shows . The anti-flood device is on. The display shows . 41 • Close the water tap and contact an Authorised Service Centre. The appliance stops and • It is normal.
www.aeg.com 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results. • Refer to "Daily use", "Hints and tips" and basket loading leaflet. • Use more intensive washing programs. • If you use multi-tablets, always switch on the option Multitab. Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level.
ENGLISH 43 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • Refer to "The water softener". Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13.
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 45 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 46 3. DESCRIPTION DE L'APPAREIL.............................................................................. 48 4. PANNEAU DE COMMANDE................................................................................. 49 5. PROGRAMMES..........................
FRANÇAIS 1. 45 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3.
FRANÇAIS 49 4. PANNEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Program touche Voyants de programme Affichage Delay touche 3 4 7 5 6 6 Option touche 7 Voyants 8 Start touche 4.1 Voyants Voyant Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de rinçage. Il s'allume au cours de la phase de rinçage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant Multitab. Voyant du réservoir de sel régénérant.
www.aeg.com 5.
FRANÇAIS 51 5.1 Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 11 0.857 225 7 - 14 0.6 - 1.4 40 - 150 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 9 - 10 1.0 - 1.2 219 - 229 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com 6.2 Adoucisseur d'eau L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région.
FRANÇAIS Si le distributeur est désactivé et que vous ne sélectionnez pas l'option Multitab, le distributeur distribuera du liquide de rinçage. 6 (dosage maximum). Le dosage 0 désactive le distributeur de liquide de rinçage, et le liquide n'est pas diffusé. Réglage usine : dosage 4. Comment régler le dosage de liquide de rinçage L'appareil doit être en mode de sélection de programme. 1.
www.aeg.com 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver d'options pendant le déroulement d'un programme. Certaines options ne sont pas compatibles entre elles. Si vous avez choisi des options incompatibles, l'appareil en désactivera automatiquement une ou plusieurs. Seuls les voyants correspondant aux options encore actives resteront allumés. 7.
FRANÇAIS 55 ATTENTION! N'essayez pas de fermer la porte de l'appareil lorsque le dispositif la maintient entrouverte. Vous risqueriez d'endommager l'appareil. Cette option s'active automatiquement lorsque vous sélectionnez le programme . Le voyant s'allume. Cette option n'est pas compatible avec d'autres programmes. • Durant la phase de séchage, un dispositif entrouvre la porte de l'appareil. • À la fin du programme, le dispositif se rétracte et la porte de l'appareil se referme.
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A B 4. Enlevez le sel qui se trouve autour de l'ouverture du réservoir de sel régénérant. C ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. 5. Tournez le couvercle du réservoir de sel régénérant vers la droite pour refermer le réservoir. De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion.
FRANÇAIS 9.1 Utilisation du produit de lavage A B C ATTENTION! Utilisez uniquement un produit de lavage spécial pour lave-vaisselle. 1. Appuyez sur la touche de déverrouillage (A) pour ouvrir le couvercle (C). 2. Versez le produit de lavage sous forme de poudre ou tablette dans le compartiment approprié (B). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle.
www.aeg.com Annulation du départ différé au cours du décompte démarrer un nouveau programme de lavage. Lorsque vous annulez le départ différé, vous devez régler de nouveau le programme et les options. Fin du programme Enfoncez simultanément les touches Delay et Option jusqu'à ce que l'appareil se mette en mode de sélection du programme. Annulation du programme Maintenez enfoncées simultanément les touches Delay et Option jusqu'à ce que l'appareil se mette en mode de sélection des programmes.
FRANÇAIS résultats de lavage et de séchage optimaux. • Si vous utilisez des pastille tout en 1, vous pouvez sélectionner l'option Multitab (si disponible). Cette option améliore les résultats de lavage et de séchage avec l'utilisation de pastilles tout en 1. • Les tablettes de détergent ne se dissolvent pas complètement durant les programmes courts.
www.aeg.com À la fin du programme, les côtés et la porte de l'appareil peuvent être mouillés. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur. Les filtres sales et les bras d'aspersion obstrués diminuent les résultats de lavage. Contrôlez-les régulièrement et nettoyezles si nécessaire. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 11.
FRANÇAIS 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 61 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices. 4.
www.aeg.com • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur • Nettoyez soigneusement l'appareil, y compris le joint en caoutchouc de la porte, avec un chiffon doux humide. • Si vous utilisez régulièrement des programmes de courte durée, des dépôts de graisse et des dépôts calcaires peuvent se former à l'intérieur de l'appareil. Pour éviter cela, nous recommandons de lancer un programme long au moins 2 fois par mois.
FRANÇAIS 63 Problème et code d'alarme Cause et solution possibles L'appareil ne se remplit pas d'eau. L'affichage indique . L'appareil ne vidange pas l'eau. L'affichage indique . Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Assurez-vous que le robinet d'eau est ouvert. • Assurez-vous que la pression de l'arrivée d'eau n'est pas trop basse. Pour obtenir cette information, contactez votre compagnie des eaux. • Assurez-vous que le robinet d'eau n'est pas obstrué.
www.aeg.com Problème et code d'alarme Cause et solution possibles L'appareil déclenche le disjoncteur. • L'ampérage n'est pas suffisant pour alimenter tous les appareils en cours de fonctionnement simultanément. Vérifiez l'ampérage de la prise et la capacité du mètre, ou éteignez l'un des appareils qui sont en cours de fonctionnement. • Défaut électrique interne de l'appareil. Faites appel à un service après vente agréé.
FRANÇAIS 65 Problème Cause et solution possibles La vaisselle est mouillée. • Le programme ne contient pas de phase de séchage ou une phase de séchage à basse température. • Le distributeur de liquide de rinçage est vide. • Il se peut que la qualité du liquide de rinçage soit en cause. • Il se peut que la qualité des pastilles tout-en-1 soit en cause. Essayez une marque différente ou activez le distributeur de liquide de rinçage et utilisez du liquide de rinçage avec les pastilles tout-en-1.
www.aeg.com Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 850 / 610 Branchement électrique1) Tension (V) 220 - 240 Fréquence (Hz) 50 / 60 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude2) max.
FRANÇAIS 67
117899552-A-052015 www.aeg.