DE Benutzerinformation Geschirrspüler FAVORIT 66600 VI1P
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................... 4 3. GERÄTEBESCHREIBUNG...............................................................................................6 4. BEDIENFELD................................................................................................................... 7 5.
DEUTSCH 1. 3 SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Allgemeine Sicherheit • • • • • • • • • Dieses Gerät ist für die Verwendung im Haushalt und ähnliche Zwecke vorgesehen, wie z. B.
www.aeg.com • • Die Lüftungsöffnungen im Gerätesockel (falls vorhanden) dürfen nicht von einem Teppichboden blockiert werden. Das Gerät muss mit den mitgelieferten neuen Schläuchen an die Wasserversorgung angeschlossen werden. Alte Schläuche dürfen nicht wieder verwendet werden. 1.
DEUTSCH • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist.
www.aeg.com 3. GERÄTEBESCHREIBUNG 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Oberster Sprüharm Oberer Sprüharm Unterer Sprüharm Filter Typenschild Salzbehälter Lüftungsschlitze 3.1 Beam-on-Floor Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Küchenboden projiziert wird. • Nach dem Start des Programms leuchtet der rote Lichtstrahl auf und bleibt während der gesamten Programmdauer eingeschaltet.
DEUTSCH 4. BEDIENFELD 1 1 2 3 4 5 2 3 Taste „Ein/Aus“ Display Delay Taste Program Taste ExtraHygiene Taste 4 6 7 8 9 5 6 7 8 9 TimeSaver Taste Multitab Taste RESET Taste Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Programmende Kontrolllampe Salz Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel Sie erlischt während des Programmbetriebs. 5.
www.aeg.
DEUTSCH Wasser (l) Energieverbrauch (kWh) Dauer (Min.) P5 10 0.9 30 P6 9 - 10 1.0 - 1.2 219 - 229 Programm 1) 9 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Möchten Sie Informationen zum Leistungstest erhalten, schicken Sie eine E-Mail an: info.test@dishwasher-production.com Notieren Sie die Produktnummer (PNC), die Sie auf dem Typenschild finden.
www.aeg.com Wasserhärte Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH). mmol/l Clarke Was- Einstellung für den serhärteWasserenthärter grade 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.
DEUTSCH , , und blinken und das Display nichts anzeigt. 2. Drücken Sie . • Die Kontrolllampen , und erlöschen. • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle Einstellung angezeigt: z.B. = Stufe 4. – Die Klarspülmittelstufen reichen von 0A bis 6A. – Stufe 0 = Es wird kein Klarspülmittel zugegeben. wiederholt, um die 3. Drücken Sie Einstellung zu ändern. 4. Drücken Sie die Taste „Ein/Aus“ zum Bestätigen der Einstellung. 6.
www.aeg.com • Die Kontrolllampen , und erlöschen. • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle = Signalton ist eingeschaltet. 4. Drücken Sie die Taste „Ein/Aus“ zum Bestätigen der Einstellung. Einstellung angezeigt: = Signalton ist ausgeschaltet. 3. Drücken Sie Einstellung. zum Ändern der 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten. Es ist nicht möglich, Optionen während eines laufenden Programms einoder auszuschalten.
DEUTSCH 7.3 ExtraHygiene Diese Option sorgt für hygienischere Ergebnisse. Während der letzten Spülphase wird die Temperatur für mindestens 10 Minuten auf 70 °C gehalten. 13 Ist die Option nicht mit dem Programm kombinierbar, leuchtet die entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. Das Display zeigt die aktualisierte Programmdauer an. Einschalten von ExtraHygiene Drücken Sie , die entsprechende Kontrolllampe leuchtet auf. 8.
www.aeg.com Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Korrosionsgefahr. Starten Sie ein Programm, nachdem Sie den Salzbehälter befüllt haben, um die Korrosion zu vermeiden. 8.2 Füllen des KlarspülmittelDosierers A B ACHTUNG! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. 1. Öffnen Sie den Deckel (C). 2. Füllen Sie den Dosierer (B) mit Klarspülmittel bis zur Marke „MAX“. 3.
DEUTSCH ACHTUNG! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (A), um den Deckel (C) zu öffnen. 2. Füllen Sie das Reinigungsmittel ein oder legen Sie eine Reinigungstablette in den Behälter (B). 3. Wenn das Programm einen Vorspülgang hat, schütten Sie eine kleine Menge Reinigungsmittel auf die Innenseite der Gerätetür. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. 9.
www.aeg.com Beenden des Programms Programmende Halten Sie RESET gedrückt, bis sich das Gerät im Programmwahlmodus befindet. Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist. Wenn das Programm beendet ist und Sie die Tür öffnen, schaltet sich das Gerät automatisch aus. Schließen Sie den Wasserhahn. 10. TIPPS UND HINWEISE 10.
DEUTSCH Reinigungsmittel, Salz und Klarspülmittel zu kehren: 1. Stellen Sie die höchste Wasserenthärterstufe ein. 2. Stellen Sie sicher, dass der Salzbehälter und der KlarspülmittelDosierer gefüllt sind. 3. Starten Sie das kürzeste Programm mit einer Spülphase. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. 4. Stellen Sie den Wasserenthärter nach Ablauf des Programms auf die Wasserhärte in Ihrer Region ein. 5. Stellen Sie die Menge des Klarspülmittels ein. 10.
www.aeg.com 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein.
DEUTSCH ACHTUNG! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger.
www.aeg.com Problem und Alarmcode Mögliche Abhilfe Das Gerät pumpt das Wasser nicht ab. • Vergewissern Sie sich, dass der Siphon nicht verstopft ist. • Vergewissern Sie sich, dass der Ablaufschlauch nicht geknickt oder zu stark gekrümmt ist. Im Display erscheint . Das Wasserauslauf-Schutzsystem ist eingeschaltet. Im Display erscheint • Drehen Sie den Wasserhahn zu und wenden Sie sich an einen autorisierten Kundendienst. . Schalten Sie nach der Überprüfung das Gerät aus und wieder ein.
DEUTSCH Spannung (V) 220 - 240 Frequenz (Hz) 50 bar (Mindest- und Höchstwert) 0.5 - 8 MPa (Mindest- und Höchstwert) 0.05 - 0.8 Wasserversorgung Kalt- oder Warmwasser2) max. 60 °C Fassungsvermögen Maßgedecke 13 Leistungsaufnahme Ein-Zustand (W) 0.99 Leistungsaufnahme Aus-Zustand (W) 0.10 Elektrischer Anschluss 1) Wasserdruck 21 1) Weitere Angaben finden Sie auf dem Typenschild. 2) Wenn Sie Heißwasser mit umweltfreundlichen, alternativen Energiequellen (z. B.
www.aeg.
DEUTSCH 23
117906711-A-302014 www.aeg.