NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 24 44 FAVORIT 66602 IM0P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant. 2.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 4 7 5 6 6 Option-toets 7 Indicatielampjes 8 Start-toets 4.1 Indicatielampjes Aanduiding Omschrijving Wasfase. Gaat aan wanneer de wasfase loopt. Spoelfase. Gaat aan wanneer de spoelfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. Einde-indicatielampje. Multitab-indicatielampje. Zoutindicatielampje.
www.aeg.com Aanduiding Omschrijving ExtraHygiene-indicatielampje. 5.
NEDERLANDS 9 5.1 Verbruikswaarden Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) 10.2 0.932 225 7 - 14 0.6 - 1.4 40 - 150 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 9 - 10 1.0 - 1.2 219 - 229 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.
www.aeg.com waterhardheid wordt gemeten in de volgende gelijkwaardige schalen. De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten. Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.
NEDERLANDS Het instellen van het glansmiddelniveau Als het doseerbakje wordt gedeactiveerd en u de optie Multitab niet kiest, laat het doseerbakje glansmiddel vrijkomen. Het apparaat moet in de programmakeuzemodus staan. 1. Houd om de gebruikersmodus in te voeren tegelijkertijd Delay en Option ingedrukt tot de indicatielampjes , en gaan knipperen en het display blanco is. 2. Druk op Delay. • De indicatielampjes 11 en gaan uit.
www.aeg.com Niet alle opties kunnen met elkaar worden gecombineerd. Als u opties hebt geselecteerd die niet met elkaar te combineren zijn, dan schakelt het apparaat automatisch één of meerdere opties uit. Alleen de indicatielampjes van de actieve opties blijven aan. 7.2 TimeSaver Met deze optie verhoogt u de druk en de temperatuur van het water. De wasen droogfasen zijn korter. De totale duur van het programma neemt met ongeveer 50% af. De wasresultaten zijn hetzelfde als bij de normale programmaduur.
NEDERLANDS Als u een programma start, doet het apparaat er ongeveer 5 minuten over om de hars in de waterontharder te herladen. Het lijkt alsof het apparaat niet werkt. De wasfase start pas nadat deze procedure voltooid is. De procedure wordt periodiek herhaald. 8.1 Het zoutreservoir LET OP! Gebruik uitsluitend zout dat specifiek is bedoeld voor gebruik in vaatwassers. 13 Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Gevaar voor roest.
www.aeg.com 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de programmakeuzemodus staat. • Vul het zoutreservoir als het zoutindicatielampje brandt. • Vul het glansmiddeldoseerbakje als het indicatielampje van het glansmiddel brandt. 3. Ruim de korven in. 4. Voeg vaatwasmiddel toe. Activeer de Multitab-optie als u multitabletten gebruikt. 5. U dient het juiste programma in te stellen en te starten voor het type lading en de mate van vervuiling. 9.
NEDERLANDS De deur openen als het apparaat in werking is Als u de deur opent terwijl een programma loopt, stopt het apparaat. Als u de deur weer sluit, gaat het apparaat verder vanaf het punt van onderbreking. 15 Controleer of er afwasmiddel in het afwasmiddeldoseerbakje aanwezig is voordat u een nieuw programma start. Einde van het programma Als het programma voltooid is, is het indicatielampje einde aan en toont het display 0:00.
www.aeg.com de schoonmaak- en droogresultaten met het gebruik van multitabletten. • Vaatwasmiddeltabletten lossen bij korte programma's niet geheel op. Om te voorkomen dat vaatwasmiddelresten op het servies achterblijven, raden we u aan om tabletten enkel bij lange programma's te gebruiken. • Gebruik niet meer dan de juiste hoeveelheid vaatwasmiddel. Zie de instructies van de vaatwasmiddelfabrikant. 10.
NEDERLANDS 17 11. ONDERHOUD EN REINIGING WAARSCHUWING! Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Vuile filters en verstopte sproeiarmen verminderen de wasresultaten. Controleer regelmatig de filters en reinig deze zo nodig. 2. Verwijder de filter (C) uit de filter (B). 3. Verwijder de platte filter (A). 4. Was de filters. 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 5.
www.aeg.com LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De bovenste sproeiarm schoonmaken 4. Om de sproeiarm weer aan de korf te bevestigen, duwt u de sproeiarm naar boven in de richting van de lagere pijl en draait u hem tegelijkertijd tegen de wijzers van de klok in, zodat hij op zijn plek vergrendelt. We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt.
NEDERLANDS progamma's met een lange duur te gebruiken. • Om de prestaties van uw apparaat op en top te houden raden we u aan iedere maand een specifiek 19 schoonmaakproduct voor vaatwasmachines te gebruiken. Volg de instructies op de verpakking van de producten zorgvuldig op. 12. PROBLEEMOPLOSSING Het apparaat start of stopt niet tijdens de werking. Kijk voordat u contact opneemt met de klantenservice of u het probleem zelf kunt oplossen met behulp van de informatie in de tabel.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing De anti-overstromingsbevei- • Draai de waterkraan dicht en neem contact op met de liging is aan. klantenservice. Op het display verschijnt . Het apparaat stopt en start meerdere keren tijdens de werking. • Dat is normaal. Dit geeft optimale schoonmaakresultaten en bespaart energie. Het programma duurt te lang. • Kies de tijdsbesparende optie om de programmaduur te verkorten (indien van toepassing).
NEDERLANDS 21 12.1 De was- en droogresultaten zijn niet naar tevredenheid Probleem Mogelijke oorzaak en oplossing Slechte wasresultaten. • Raadpleeg "Dagelijks gebruik", "Aanwijzingen en tips" en de folder voor het laden van de korf. • Gebruik intensievere wasprogramma´s. • Schakel altijd de optie Multitab in als u multitabletten gebruikt. Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan. • Het glansmiddel is op of de dosering van glansmiddel is niet voldoende.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water. middeldoseerbakje. • Het water kan het vaatwasmiddel niet uit het vaatwasmiddeldoseerbakje spoelen. Zorg ervoor dat de bovenste sproeiarm niet geblokkeerd of verstopt is.
NEDERLANDS 23 14. MILIEUBESCHERMING Recycle de materialen met het symbool . Gooi de verpakking in een geschikte verzamelcontainer om het te recyclen. Help om het milieu en de volksgezondheid te beschermen en recycle het afval van elektrische en elektronische apparaten. Gooi apparaten gemarkeerd met het symbool niet weg met het huishoudelijk afval. Breng het product naar het milieustation bij u in de buurt of neem contact op met de gemeente.
www.aeg.com CONTENTS 1. SAFETY INFORMATION.........................................................................................25 2. SAFETY INSTRUCTIONS........................................................................................ 26 3. PRODUCT DESCRIPTION...................................................................................... 27 4. CONTROL PANEL...................................................................................................28 5. PROGRAMMES................
ENGLISH 1. 25 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
www.aeg.com 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Cutlery basket 11 Lower basket 12 Upper basket 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase.
ENGLISH Indicator Description Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates. TimeSaver indicator. Delay indicator. ExtraHygiene indicator. 5.
www.aeg.com Programme 5) Degree of soil Type of load Programme phases • Normal soil • Prewash • Crockery and cut- • Wash 50 °C lery • Rinses • Dry Options • Multitab 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
ENGLISH 31 • The deactivation of the rinse aid dispenser when you want to use the Multitab option without rinse aid. • The level of rinse aid according to the required dosage. Press and hold simultaneously Delay and Option until the appliance is in programme selection mode. These settings will be saved until you change them again. The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance.
www.aeg.com • The indicator continues to flash. • The display shows the current setting: e.g. = level 5. 3. Press Program again and again to change the setting. 4. Press the on/off button to confirm the setting. 6.3 The rinse aid dispenser The rinse aid helps to dry the dishes without streaks and stains. The rinse aid is automatically released during the hot rinse phase. You can set the released quantity of rinse aid between level 1 (minimum quantity) and level 6 (maximum quantity).
ENGLISH 33 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on. 7.
www.aeg.com 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. When you start a programme, the appliance can take up to 5 minutes to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure will be repeated periodically. 8.1 The salt container 5.
ENGLISH 35 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. If you use multitablets, activate the option Multitab. 5. Set and start the correct programme for the type of load and the degree of soil. 9.2 Setting and starting a programme 9.
www.aeg.com the running phase comes on. The delay indicator goes off. Opening the door while the appliance operates If you open the door while a programme is running, the appliance stops. When you close the door, the appliance continues from the point of interruption. Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Press simultaneously Delay and Option until the appliance is in programme selection mode.
ENGLISH drying results with the use of multitablets. • Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with long programmes. • Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1.
www.aeg.com 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 1. Turn the filter (B) counterclockwise and remove it. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B).
ENGLISH 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. 39 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. Clogged holes can cause unsatisfactory washing results. 1. Pull out the upper basket. 2.
www.aeg.com With some problems, the display shows an alarm code. to contact an Authorised Service Centre. The majority of problems that can occur can be solved without the need Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The programme does not start. • Make sure that the appliance door is closed. • Press Start.
ENGLISH 41 Problem and alarm code Possible cause and solution Small leak from the appliance door. • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • Parts of the tableware are protruding from the baskets.
www.aeg.com Problem Possible cause and solution The dishes are wet. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together. The interior of the appliance is • This is not a defect of the appliance. it is caused by wet.
ENGLISH Voltage (V) 220 - 240 Frequency (Hz) 50 / 60 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 0.99 Power consumption Off-mode (W) 0.10 Electrical connection 1) Water supply pressure 43 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g.
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 45 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 46 3. DESCRIPTION DE L'APPAREIL.............................................................................. 48 4. PANNEAU DE COMMANDE................................................................................. 49 5. PROGRAMMES..........................
FRANÇAIS 1. 45 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3.
FRANÇAIS 49 4. PANNEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Program touche Voyants de programme Affichage Delay touche 3 4 7 5 6 6 Option touche 7 Voyants 8 Start touche 4.1 Voyants Voyant Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de rinçage. Il s'allume au cours de la phase de rinçage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant de fin. Voyant Multitab. Voyant du réservoir de sel régénérant.
www.aeg.com Voyant Description Voyant ExtraHygiene. 5.
FRANÇAIS 51 5.1 Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 10.2 0.932 225 7 - 14 0.6 - 1.4 40 - 150 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 9 - 10 1.0 - 1.2 219 - 229 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com 6.2 Adoucisseur d'eau L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région.
FRANÇAIS Si le distributeur est désactivé et que vous ne sélectionnez pas l'option Multitab, le distributeur distribuera du liquide de rinçage. 6 (dosage maximum). Le dosage 0 désactive le distributeur de liquide de rinçage, et le liquide n'est pas diffusé. Réglage usine : dosage 4. Comment régler le dosage de liquide de rinçage L'appareil doit être en mode de sélection de programme. 1.
www.aeg.com 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver d'options pendant le déroulement d'un programme. Certaines options ne sont pas compatibles entre elles. Si vous avez choisi des options incompatibles, l'appareil en désactivera automatiquement une ou plusieurs. Seuls les voyants correspondant aux options encore actives resteront allumés. 7.
FRANÇAIS 55 8. AVANT LA PREMIÈRE UTILISATION 1. Assurez-vous que le réglage actuel de l'adoucisseur d'eau est compatible avec la dureté de l'arrivée d'eau. Si ce n'est pas le cas, réglez le niveau de l'adoucisseur d'eau. 2. Remplissez le réservoir de sel régénérant. 3. Remplissez le distributeur de liquide de rinçage. 4. Ouvrez le robinet d'eau. 5. Lancez un programme pour éliminer tous les résidus qui peuvent toujours se trouver à l'intérieur de l'appareil.
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. B 1. Ouvrez le couvercle (C). 2. Remplissez le distributeur (B) jusqu'à ce que le liquide de rinçage atteigne le repère « MAX ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement.
FRANÇAIS petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. 9.2 Réglage et départ d'un programme Fonction Auto Off Cette fonction réduit la consommation d'énergie en éteignant automatiquement l'appareil lorsqu'il ne fonctionne pas. La fonction s'active : • 5 minutes après la fin du programme de lavage. • Au bout de 5 minutes si le programme n'a pas démarré. Départ d'un programme 1.
www.aeg.com Toutes les touches sont inactives, sauf la touche marche/arrêt. 1. Pour éteindre l'appareil, appuyez sur la touche marche/arrêt ou attendez que la fonction Auto Off l'éteigne automatiquement. Si vous ouvrez la porte avant l'activation de Auto Off, l'appareil est automatiquement éteint. 2. Fermez le robinet d'arrivée d'eau. 10. CONSEILS 10.
FRANÇAIS 10.3 Que faire si vous ne voulez plus utiliser de pastilles de détergent multifonctions Avant de commencer à utiliser du produit de lavage, du sel régénérant et du liquide de rinçage séparément, effectuez la procédure suivante : 1. Réglez l'adoucisseur d'eau au niveau maximal. 2. Assurez-vous que le réservoir de sel régénérant et le distributeur de liquide de rinçage sont pleins. 3. Lancez le programme le plus court avec une phase de rinçage.
www.aeg.com Les filtres sales et les bras d'aspersion obstrués diminuent les résultats de lavage. Contrôlez-les régulièrement et nettoyezles si nécessaire. 11.1 Nettoyage des filtres Le système de filtrage se compose de trois éléments. 4. Lavez les filtres. C B A 1. Faites pivoter le filtre (B) dans le sens antihoraire puis sortez-le. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 5.
FRANÇAIS ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 61 4. Pour réinstaller le bras d'aspersion supérieur sur le panier, poussez le bras d'aspersion vers le haut, dans la direction indiquée par la flèche du bas, tout en le tournant vers la gauche jusqu'à ce qu'il se bloque en place.
www.aeg.com • Pour maintenir des performances optimales, nous vous recommandons d'utiliser un produit de nettoyage spécifique pour lave-vaisselle une fois par mois. Reportez-vous aux instructions figurant sur l'emballage de ces produits. 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête en cours de programme. Avant de contacter le service après-vente agréé, vérifiez si vous pouvez résoudre le problème par vous-même à l'aide des informations du tableau.
FRANÇAIS 63 Problème et code d'alarme Cause et solution possibles L'appareil ne vidange pas l'eau. L'affichage indique . Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Assurez-vous que le siphon de l'évier n'est pas obstrué. • Assurez-vous que le filtre du tuyau de vidange de l'eau n'est pas obstrué. • Assurez-vous que le système du filtre intérieur n'est pas obstrué. • Assurez-vous que le tuyau de vidange n'est pas tordu ni plié.
www.aeg.com Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. Après avoir vérifié l'appareil, éteignez puis rallumez-le. Si le problème persiste, contactez le service après-vente agréé. Pour les codes d'alarme ne figurant pas dans le tableau, contactez le service après-vente agréé. 12.
FRANÇAIS 65 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com Pression de l'arrivée d'eau bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 0.99 Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour les autres valeurs.
FRANÇAIS 67
117901152-A-052015 www.aeg.