EN DE User Manual Dishwasher Benutzerinformation Geschirrspüler 2 20 FAVORIT 66682 M0P
www.aeg.com CONTENTS 1. SAFETY INFORMATION...........................................................................................3 2. SAFETY INSTRUCTIONS.......................................................................................... 4 3. PRODUCT DESCRIPTION........................................................................................ 5 4. CONTROL PANEL.....................................................................................................6 5. PROGRAMMES.............
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com 1.2 Children and vulnerable people safety • • • • • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Do not let children play with the appliance. Keep all detergents away from children.
ENGLISH • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed. There can be detergent on the dishes. • The appliance can release hot steam if you open the door while a programme operates. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. 2.
www.aeg.com 3.1 Beam-on-Floor • When the appliance has a malfunction, the red light flashes. The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door. The Beam-on-Floor goes off when the appliance is deactivated. • When the programme starts, a red light comes on and stays on for all the duration of the programme. • When the programme is completed, a green light comes on. 4.
ENGLISH Programme Degree of soil Type of load Programme phases Options • All AUTOSENSE 2) • Crockery, cutlery, pots and pans • Prewash • Wash from 45 °C to 70 °C • Rinses • Dry • Multitab P3 • Mixed soil • Crockery, cutlery, pots and pans • • • • Prewash Wash 50 °C and 65 °C Rinses Dry • TimeSaver • Multitab • Heavy soil • Crockery, cutlery, pots and pans • • • • Prewash Wash 70 °C Rinses Dry • TimeSaver • Multitab P5 GLASS • Normal or light soil • Delicate crockery and glassware • Wash 4
www.aeg.com 5.1 Consumption values Water (l) Energy (kWh) Duration (min) P1 ECO 10.2 0.932 225 P2 AUTOSENSE 7 - 14 0.6 - 1.4 40 - 150 P3 PROZONE 14 - 16 1.2 - 1.5 139 - 149 12.5 - 14.5 1.4 - 1.6 154 - 164 P5 GLASS 12 - 14 0.7 - 0.9 75 - 85 P6 30MIN 10 0.9 30 P7 PREWASH 4 0.1 14 9 - 10 1.0 - 1.
ENGLISH can set the programme selection mode in the following way: Press and hold RESET until the appliance is in programme selection mode. 6.2 The water softener The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance. 9 The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales.
www.aeg.com will deactivate the rinse aid dispenser and no rinse aid will be released. Factory setting: level 4. How to set the rinse aid level The appliance must be in programme selection mode. 1. To enter the user mode, press and and hold simultaneously until the indicators , , and start to flash and the display is blank. 2. Press . • The indicators off. , and go • The indicator continues to flash. • The display shows the current = level 4. setting: e.g.
ENGLISH • If options have been saved together with the programme, the indicators related to the options come on. 6.6 Acoustic signals Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals. There is also an acoustic signal that sounds when the programme is completed. By default this acoustic signal is deactivated but it is possible to activate it. How to activate the acoustic signal for the end of programme 11 1.
www.aeg.com The washing results are the same as with the normal programme duration. The drying results can decrease. How to activate TimeSaver Press If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated programme duration. , the related indicator comes on. 8. BEFORE FIRST USE 1.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 13 CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. C 9. DAILY USE 1. Open the water tap. 2.
www.aeg.com Starting a programme 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press repeatedly until the display shows the number of the programme you want to start. The display will show the programme number for approximately 3 seconds and then show the programme duration. • If you want to select the MyFavourite programme, press .
ENGLISH can use the multi-tablets (e.g. ''3in1'', ''4in1'', ''All in 1''). Follow the instructions written on the packaging. • Select the programme according to the type of load and degree of soil. With the ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance.
www.aeg.com 10.6 Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket. At the end of the programme water can still remain on the sides and on the door of the appliance. 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket.
ENGLISH 17 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.
www.aeg.com Problem and alarm code Possible solution The programme does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. The appliance does not fill with water. • Make sure that the water tap is open.
ENGLISH 19 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 850 / 610 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 0.99 Power consumption Off-mode (W) 0.10 Water supply pressure 1) Refer to the rating plate for other values.
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.......................................................................... 21 2. SICHERHEITSANWEISUNGEN.............................................................................. 22 3. GERÄTEBESCHREIBUNG.......................................................................................24 4. BEDIENFELD........................................................................................................... 25 5. PROGRAMME.................
DEUTSCH 1. 21 SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Allgemeine Sicherheit • • • • • • • • • Dieses Gerät ist für die Verwendung im Haushalt und ähnliche Zwecke vorgesehen, wie z. B.
www.aeg.com • • Die Lüftungsöffnungen im Gerätesockel (falls vorhanden) dürfen nicht von einem Teppichboden blockiert werden. Das Gerät muss mit den mitgelieferten neuen Schläuchen an die Wasserversorgung angeschlossen werden. Alte Schläuche dürfen nicht wieder verwendet werden. 1.
DEUTSCH • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist.
www.aeg.com 3. GERÄTEBESCHREIBUNG 1 2 3 4 13 12 1 2 3 4 5 6 7 11 10 9 Arbeitsplatte Oberster Sprüharm Oberer Sprüharm Unterer Sprüharm Filter Typenschild Salzbehälter 3.1 Beam-on-Floor Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Küchenboden projiziert wird. • Nach dem Start des Programms leuchtet der rote Lichtstrahl auf und bleibt während der gesamten Programmdauer eingeschaltet.
DEUTSCH 25 4. BEDIENFELD 2 1 1 2 3 4 5 Taste „Ein/Aus“ Display Taste Program Taste Delay Taste MyFavourite 3 6 7 8 9 4 5 6 7 8 9 Taste TimeSaver Taste Multitab Taste RESET Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Salz Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel Sie erlischt während des Programmbetriebs. 5.
www.aeg.
DEUTSCH 27 5.1 Verbrauchswerte Wasser (l) Energieverbrauch (kWh) Dauer (Min.) P1 ECO 10.2 0.932 225 P2 AUTOSENSE 7 - 14 0.6 - 1.4 40 - 150 P3 PROZONE 14 - 16 1.2 - 1.5 139 - 149 12.5 - 14.5 1.4 - 1.6 154 - 164 P5 GLASS 12 - 14 0.7 - 0.9 75 - 85 P6 30MIN 10 0.9 30 P7 PREWASH 4 0.1 14 9 - 10 1.0 - 1.
www.aeg.com Wenn Sie das Gerät einschalten, befindet es sich normalerweise im Programmwahlmodus. Anderenfalls können Sie den Programmwahlmodus folgendermaßen einstellen: Je höher der Mineralgehalt ist, um so härter ist das Wasser. Die Wasserhärte wird in gleichwertigen Einheiten gemessen. Halten Sie RESET gedrückt, bis sich das Gerät im Programmwahlmodus befindet. 6.
DEUTSCH 6.3 Klarspülmittel-Dosierer Klarspülmittel ermöglichen das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphasen abgegeben. Sie können die Zugabemenge für Klarspülmittel zwischen Stufe 1 (Mindestmenge) und Stufe 6 (Höchstmenge) einstellen. Bei Stufe 0 wird der Klarspülmittel-Dosierer ausgeschaltet und es wird kein Klarspülmittel zugegeben. Werkseitige Einstellung: Stufe 4. Das Gerät muss sich im Programmwahlmodus befinden.
www.aeg.com Sie können nur 1 Programme speichern. Wenn Sie ein anderes Programm speichern, wird das zuvor gespeicherte Programm gelöscht. Es ertönt auch ein Signalton, wenn das Programm beendet ist. Standardmäßig ist dieser Signalton ausgeschaltet, es ist jedoch möglich, ihn einzuschalten. So speichern Sie das Programm MyFavourite: So schalten Sie den Signalton für das Programmende ein 1. Stellen Sie das Programm ein, das Sie speichern möchten.
DEUTSCH die Salz, Klarspül- und Reinigungsmittel enthalten. Sie enthalten zum Teil auch andere Reinigungs- und Spülmittel. Diese Option schaltet die Zufuhr von Salz aus. Die Salz-Kontrolllampe leuchtet nicht. Diese Option schaltet auch die Zufuhr von Klarspülmittel aus, wenn der Klarspülmittel-Dosierer ausgeschaltet ist (die Kontrolllampe des KlarspülmittelDosierers leuchtet nicht).
www.aeg.com 8.2 Füllen des KlarspülmittelDosierers A B 4. Entfernen Sie das Salz, das sich um die Öffnung des Salzbehälters herum angesammelt hat. C 5. Drehen Sie den Deckel des Salzbehälters im Uhrzeigersinn, um den Salzbehälter zu schließen. Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Korrosionsgefahr. Starten Sie ein Programm, nachdem Sie den Salzbehälter befüllt haben, um die Korrosion zu vermeiden. ACHTUNG! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler.
DEUTSCH 9.1 Verwenden des Reinigungsmittels A B 33 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. 3. Drücken Sie wiederholt , bis im Display die Nummer des gewünschten Programms erscheint. Die Programmnummer wird etwa 3 Sekunden lang im Display angezeigt, anschließend erscheint die Programmdauer. • Wenn Sie das Programm MyFavourite wählen möchten, C ACHTUNG! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1.
www.aeg.com schließen, läuft das Programm ab dem Zeitpunkt der Unterbrechung weiter. Wenn die Tür während der Trockenphase länger als 30 Sekunden geöffnet wird, wird das laufende Programm beendet. Abbrechen einer eingestellten Zeitvorwahl während des Countdowns Wenn Sie die eingestellte Zeitvorwahl abbrechen, müssen das Programm und die Optionen erneut eingestellt werden. Halten Sie RESET gedrückt, bis sich das Gerät im Programmwahlmodus befindet.
DEUTSCH Reinigungsmittel-Rückstände auf dem Geschirr zurückbleiben. • Verwenden Sie nicht mehr als die angegebene Reinigungsmittelmenge. Siehe hierzu die Angaben auf der Reinigungsmittelverpackung. 10.3 Was tun, wenn Sie keine Multi-Reinigungstabletten mehr verwenden möchten Vorgehensweise, um zurück zur separaten Verwendung von Reinigungsmittel, Salz und Klarspülmittel zu kehren: 1. Stellen Sie die höchste Wasserenthärterstufe ein. 2.
www.aeg.com 11. REINIGUNG UND PFLEGE WARNUNG! Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden. Verschmutzte Filter und verstopfte Sprüharme beeinträchtigen das Spülergebnis. Prüfen Sie die Filter regelmäßig und reinigen Sie diese, falls nötig. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. 4. Reinigen Sie die Filter.
DEUTSCH 37 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger.
www.aeg.com Problem und Alarmcode Mögliche Abhilfe Das Programm startet nicht. • Vergewissern Sie sich, dass die Tür geschlossen ist. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab, oder warten Sie, bis sie abgelaufen ist. • Das Gerät regeneriert das Filterharz des Wasserenthärters. Dieser Vorgang dauert ca. 5 Minuten. Es läuft kein Wasser in das Gerät. • Vergewissern Sie sich, dass der Wasserzulauf geöffnet ist.
DEUTSCH 39 Problem Mögliche Abhilfe Das Geschirr ist nass. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur. • Der Klarspülmittel-Dosierer ist leer. • Die Ursache kann in der Qualität des Klarspülmittels liegen. • Die Ursache kann in der Qualität der Multi-Reinigungstabletten liegen. Probieren Sie eine andere Marke aus oder schalten Sie den Klarspülmittel-Dosierer ein und verwenden Sie ihn zusammen mit den Multi-Reinigungstabletten.
117895750-A-372014 www.aeg.