PL Instrukcja obsługi Zmywarka FAVORIT 66702 M0P FAVORIT 66702 W0P
www.aeg.com SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA................................................. 3 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA.................................................. 4 3. OPIS URZĄDZENIA................................................................................................. 6 4. PANEL STEROWANIA.............................................................................................7 5. PROGRAMY.............................................................
POLSKI 1. 3 INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA Przed instalacją i rozpoczęciem eksploatacji urządzenia należy uważnie zapoznać się z załączoną instrukcją obsługi. Producent nie odpowiada za uszkodzenia i obrażenia ciała spowodowane nieprawidłową instalacją i eksploatacją. Należy zachować instrukcję wraz z urządzeniem do wykorzystania w przyszłości. 1.
www.aeg.com • Urządzenie należy podłączyć do instalacji wodociągowej za pomocą nowego zestawu węży dostarczonych w komplecie z urządzeniem. Nie wolno używać starego zestawu węży. 1.
POLSKI • • • • • • • Należy używać wyłącznie prawidłowo zamontowanego gniazda elektrycznego z uziemieniem. Nie stosować rozgałęźników ani przedłużaczy. Należy zwrócić uwagę, aby nie uszkodzić wtyczki ani przewodu zasilającego. Wymiany przewodu zasilającego można dokonać wyłącznie w naszym autoryzowanym centrum serwisowym. Podłączyć wtyczkę do gniazda elektrycznego dopiero po zakończeniu instalacji. Należy zadbać o to, aby w zainstalowanym urządzeniu wtyczka przewodu zasilającego była łatwo dostępna.
www.aeg.com • Wymontować zatrzask drzwi, aby uniemożliwić zamknięcie się dzieci lub zwierząt w urządzeniu. 3.
POLSKI 4. PANEL STEROWANIA 1 2 3 8 1 2 3 4 5 4 7 Przycisk wł./wył. Przycisk Program Wskaźniki programów Wyświetlacz Przycisk Delay 5 6 6 Przycisk Option 7 Wskaźniki 8 Przycisk Start 4.1 Wskaźniki Wskaźnik Opis Faza zmywania. Włącza się podczas fazy zmywania. Faza płukania. Włącza się podczas fazy płukania. Faza suszenia. Zapala się podczas fazy suszenia. Wskaźnik zakończenia programu. Wskaźnik funkcji Multitab. Wskaźnik soli. W trakcie programu wskaźnik ten jest zawsze wyłączony.
www.aeg.com 5.
POLSKI 9 5.1 Parametry eksploatacyjne Program1) Zużycie wody (l) Zużycie energii (kWh) Czas trwania (min) 11 0.961 225 7 - 14 0.6 - 1.4 40 - 150 12.5 - 14.5 1.4 - 1.6 154 - 164 12 - 14 0.7 - 0.9 75 - 85 10 0.9 30 9 - 10 1.0 - 1.2 219 - 229 1) Parametry eksploatacyjne mogą ulec zmianie w zależności od ciśnienia i temperatury wody, zmian w napięciu zasilania, użytych opcji oraz ilości naczyń. 5.
www.aeg.com Twardość wody jest mierzona w równoważnych skalach. lokalnym zakładzie wodociągowym można uzyskać informację na temat twardości wody. Istotne jest ustawienie właściwego poziomu zmiękczania wody, aby zapewnić dobre rezultaty zmywania. Zmiękczanie powinno być dostosowane do stopnia twardości wody doprowadzonej do urządzenia. W Twardość wody Stopnie nie‐ mieckie (°dH) Stopnie fran‐ cuskie (°fH) mmol/l Stopnie Clarka Poziom zmiękcza‐ nia wody 47 - 50 84 - 90 8.4 - 9.
POLSKI Regulacja dozowania płynu nabłyszczającego Urządzenie musi być w trybie wyboru programów. 1. Aby uruchomić tryb użytkownika, nacisnąć jednocześnie i przytrzymać przyciski Delay i Option, aż , i wskaźniki zaczną migać, a wyświetlacz będzie pusty. 2. Nacisnąć Delay. • Wskaźniki wyłączą się. • będzie nadal Wskaźnik migał. Na wyświetlaczu pojawi się • i aktualne ustawienie: np. = poziom 4. – Poziom dozowania płynu nabłyszczającego można ustawić od 0A do 6A.
www.aeg.com 7.1 Multitab Włączyć tę opcję w przypadku stosowania tabletek wieloskładnikowych z solą, płynem nabłyszczającym i detergentem. Mogą one zawierać także inne środki do mycia lub płukania. Opcja ta powoduje wyłączenie dozowania soli. Nie włącza się wskaźnik soli. Użycie tej opcji powoduje wydłużenie czasu trwania programu w celu poprawy efektów zmywania i suszenia podczas używania tabletek wieloskładnikowych. Multitab nie jest opcją stałą, dlatego należy ją włączać przy każdym cyklu.
POLSKI Napełnianie zbiornika soli 1. Obrócić pokrywkę zbiornika soli w lewo i ją zdjąć. 2. Wlać 1 litr wody do zbiornika soli (tylko za pierwszym razem). 3. Napełnić zbiornik soli solą do zmywarek. 13 8.2 Napełnianie dozownika płynu nabłyszczającego A B C 4. Usunąć sól rozsypaną wokół otworu zbiornika soli. 5. Obrócić pokrywkę zbiornika soli w prawo, aby zamknąć zbiornik soli. Podczas napełniania zbiornika soli może się z niego wydostawać woda i sól. Zagrożenie wystąpieniem korozji.
www.aeg.com 9.1 Stosowanie detergentu A B C UWAGA! Stosować wyłącznie detergent przeznaczony do zmywarek. 1. Nacisnąć przycisk zwalniający (A), aby otworzyć pokrywę (C). 2. Umieścić detergent, w postaci proszku lub tabletki, w przegródce (B). 3. Jeśli program przewiduje fazę zmywania wstępnego, umieścić niewielką ilość detergentu na wewnętrznej stronie drzwi urządzenia. 4. Zamknąć pokrywę. Upewnić się, że pokrywa jest zablokowana. 9.
POLSKI Anulowanie programu Nacisnąć jednocześnie i przytrzymać przyciski Delay i Option, aż urządzenie znajdzie się w trybie wyboru programów. Przed uruchomieniem nowego programu należy upewnić się, że w dozowniku znajduje się detergent. Zakończenie programu Po zakończeniu programu na wyświetlaczu pojawi się symbol 0:00 15 oraz zaświeci się wskaźnik zakończenia programu. Wszystkie przyciski są nieaktywne z wyjątkiem przycisku wł./wył. 1. Nacisnąć przycisk wł./wył.
www.aeg.com 10.3 Postępowanie w przypadku zaprzestania korzystania z tabletek wieloskładnikowych Przed rozpoczęciem stosowania oddzielnie dozowanego detergentu, soli i płynu nabłyszczającego należy wykonać poniższą procedurę. 1. Ustawić najwyższy poziom zmiękczania wody. 2. Upewnić się, że zbiornik soli oraz dozownik płynu nabłyszczającego są pełne. 3. Uruchomić najkrótszy program z fazą płukania. Nie dodawać detergentu ani nie umieszczać naczyń w koszach. 4.
POLSKI 17 11.1 Czyszczenie filtrów System filtrów składa się z 3 części. C B A 1. Obrócić filtr (B) przeciwnie do ruchu wskazówek zegara i wyjąć go. 5. Upewnić się, że wokół krawędzi osadnika nie znajdują się resztki żywności ani zanieczyszczenia. 6. Włożyć na miejsce filtr płaski (A). Upewnić się, że jest prawidłowo umieszczony pod 2 prowadnicami. 7. Włożyć filtry (B) i (C). 8. Włożyć filtr (B) do filtra płaskiego (A). Obrócić zgodnie z ruchem wskazówek zegara, aż się zablokuje. 2.
www.aeg.com UWAGA! Nieprawidłowe umiejscowienie filtrów może skutkować niezadowalającymi efektami zmywania i uszkodzeniem urządzenia. 11.2 Czyszczenie ramion spryskujących Nie wolno wyjmować ramion spryskujących. Jeżeli otwory w ramionach spryskujących są zatkane, zabrudzenia należy usunąć przy pomocy cienkiego i zaostrzonego przedmiotu. 11.3 Czyszczenie obudowy • • • Używać wyłącznie neutralnych detergentów. Nie używać produktów ściernych, myjek do szorowania ani rozpuszczalników. 11.
POLSKI Problem i kod alarmowy Możliwe rozwiązanie Urządzenie nie napełnia się • wodą. • Na wyświetlaczu pojawia się wskazanie . Sprawdzić, czy zawór wody jest otwarty. Upewnić się, że ciśnienie wody nie jest zbyt niskie. W tym celu należy skontaktować się z miejscowym za‐ kładem wodociągowym. Upewnić się, że zawór wody jest drożny. Upewnić się, że filtr w wężu dopływowym jest drożny. Upewnić się, że wąż dopływowy nie jest zagięty ani przygnieciony. • • • Urządzenie nie wypompo‐ • wuje wody.
www.aeg.com 13. DANE TECHNICZNE Wymiary Szerokość / Wysokość / Głębokość (mm) 596 / 850 / 610 Podłączenie do sieci elek‐ Napięcie (V) 220 - 240 trycznej 1) Częstotliwość (Hz) 50 Ciśnienie doprowadzanej wo‐ Min./maks. bar (MPa) dy 0.5 (0.05) / 8 (0.8) Dopływ wody Zimna lub ciepła woda2) maks. 60°C Pojemność Liczba standardowych nak‐ ryć 15 Pobór mocy Tryb czuwania (W) 0.99 Pobór mocy Tryb wyłączenia (W) 0.10 1) Pozostałe wartości znajdują się na tabliczce znamionowej.
POLSKI 21
www.aeg.
POLSKI 23
117904710-E-182014 www.aeg.